Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Mutagenicity of three agricultural soils

A chemical and biological testing protocol was employed to evaluate the mutagenic potential of the organic compounds extracted from three agricultural soils. The analytical procedures used included bioassays with Salmonella typhimurium and Aspergillus nidulans for the detection of point mutations and a gas chromatography/mass spectrometry/computer system to identify major organic constituents. The extracts of all three soils exhibited mutagenic response in the bioassays. At a dose level of 1000 micrograms per plate, the organic extract of the Bastrop clay induced 434 net revertants; while at the same dose level the Norwood sandy clay and the Sassafrass sandy loam induced 35 and 178 net revertants, respectively, in the Salmonella assay with metabolic activation. In the Aspergillus assay, the extract of the Norwood and Bastrop soils induced a positive response without metabolic activation; this effect was reduced or eliminated in the presence of metabolic activation. Chemical analysis identified a variety of initiators, promotors, inhibitors, and cocarcinogens; however, there were no mutagenic compounds identified in any of the soil extracts. The results of this combined testing protocol indicate that the agricultural soils tested had an inherent level of mutagenic activity, which was not detected by GC/MS analysis alone, and this activity may be related to the past history of agricultural practices, including biocide applications, fertilization, and cultivation.     

The Silicon Backplane Design for an LCOS Polarization-Insensitive Phase Hologram SLM

Polarization-insensitivity is achieved in a reflective spatial light modulator by laying a quarter-wave plate (QWP) at the incident wavelength directly over the mirror pixels of a silicon backplane, and forming a nematic Freedrickcz cell over the QWP to modulate the reflected phase. To achieve the highest drive voltage from the available silicon process, a switched voltage common front electrode design is described, with variable amplitude square wave drive to the pixels to maintain constant root-mean-square drive and minimize phase fluctuations during the dc balance refresh cycle. The silicon has been fabricated and liquid-crystal-on-silicon cells both with and without the QWP assembled; applications include optically transparent switches for optical networks, beam steering for add-drop multiplexers for wavelength-division-multiplexing telecommunications, television multicast, and holographic projection.     

Visual insights into high-resolution earthquake Simulations.

This study focuses on the visualization of a series of large earthquake simulations collectively called TeraShake. The simulation series aims to assess the impact of San Andreas Fault earthquake scenarios in Southern California. We discuss the role of visualization in gaining scientific insight and aiding unexpected discoveries.     

Exploiting ILP, TLP, and DLP with the polymorphous trips architecture

The Tera-op reliable intelligently adaptive processing system (TRIPS) architecture seeks to deliver system-level configurability to applications and runtime systems. It does so by employing the concept of polymorphism, which permits the runtime system to configure the hardware execution resources to match the mode of execution and demands of the compiler and application.     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.     

Prediction of Undrained Sinkhole Collapse

Sinkholes are surface depressions or shafts resulting from the collapse of a submerged cavity in soil. The cavities that lead to sinkholes form as a result of underlying geology in limestone areas, or as a result of human activity such as mining or leakage from a sewer. The formation of sinkholes is often sudden and can lead to extensive damage and loss of life, especially in urban areas. Much of the literature on the subject of sinkhole formation is empirical in nature, often being associated with specific locations. This paper presents the results of a study, using numerical modeling, of the undrained stability of the submerged cavities that lead to sinkhole formation. Finite-element limit analysis techniques (using programs developed at the University of Newcastle) are used to obtain upper and lower bound values of a suitable load parameter, which bracket the exact solution. The results are compared to analytical solutions, both from literature and derived independently.     

A Finite Element Computational Method for Gas Hydrate. Part I: Theory

A finite element scheme is presented to model the dissociation of gas hydrates in porous media by hot water injection. We show a complete derivation of the finite element formulation, including the associated mass and energy conservation equations capable of performing transient analysis of both conductive and convective heat transfer for gas and liquid flow in porous media. The scheme also includes the latent heat effect to accommodate the change of phase due to melting of hydrate. In the companion paper, Part II, this method is successfully applied to hydrate reservoirs.