Rheological study on O−carboxymethylated chitosan/cellulose polyblends from LiCl/N,N‐dimethylacetamide solution

An O?carboxymethylated chitosan (O? CMCh) water solution (I) and N,N‐dimethylacetamide (DMAc) emulsion (II) were blended with a cellulose LiCl/DMAc solution, and corresponding polyblends (Polyblends I and II) were obtained. The rheology of the three fluids, that is, the cellulose solution and Polyblends I and II, was investigated. The cellulose solution was characterized by a power‐law fluid. When an O‐CMCh water solution or DMAc emulsion was added to the cellulose solution, the power‐law curve was preserved. The power‐law indexes (n) of all three fluids increased along with the temperature. Polyblend I displays an n close to but a little higher than that of the cellulose solution, while Polyblend II shows a much higher power index than those of the other two fluids. The values of the apparent viscosity (η_a) for all the three fluids are close and decrease along with an increase in the temperature. Adding O‐CMCh microparticles into Polyblends I and II results in a decrease in the structural viscosity index (Δη) in comparison to that of the cellulose solution, and this effect is very obvious for Polyblend I. A cellulose solution's Δη declines with the augmentation of temperature, while the Δη's of both Polyblends I and II show minimum values at about 323 K. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1719–1725, 2003     

基体树脂对长玻璃纤维增强PP力学性能的影响

采用在线混合设备制备了长玻璃纤维(LGF)增强聚丙烯(PP)复合材料(LGF-PP),研究了基体性质及界面相容剂对LGF-PP力学性能的影响。基体树脂熔体流动速率的增加,使最终LGF-PP中的玻璃纤维长度从5.63 mm增至8.56 mm,提高了力学性能。与均聚PP比较,以共聚PP为基体树脂的LGF-PP冲击强度高出约10%,但其他性能略差。界面相容剂有利于增强玻璃纤维与PP的界面结合,拉伸强度和拉伸模量明显增加,但是冲击强度降低了20%～30%。     

不同处理方式对稻瘟病菌丝致畸作用的比较

用清水、链霉菌D–2的复合诱变菌株和农药春雷霉素3种方式对稻瘟病菌丝进行了处理。结果表明,清水处理对稻瘟病菌丝无任何影响,复合诱变菌株对稻瘟病菌丝的致畸作用主要表现在导致菌丝扭曲和膨大,农药处理对菌丝的致畸作用是使菌丝伸长受抑制,导致菌丝呈颗粒状。     

水解-水热体系中同质异构TiO2纳米晶生成机理的分子模拟研究

在实验研究的基础上,采用分子模拟的方法,对在水解-水热体系中TiO2纳米颗粒晶相生成原理进行了系统的模拟计算和建模研究,文章介绍了分子模拟软件Hyperchem的计算方法,建立了钛离子水解过程和能量分布模型,利用模拟计算和模型,直观和定量分析了水解中间产物、水热晶化过程以及最终产物间的关系。研究了pH值对同质异构相成因的影响机理;静电场作用对同质异构相生成的影响。考察了水合络离子的连接方式,指出顶角连接与棱边连接保持到最终产物的结构中。从能量的角度揭示了同质异构TiO2晶型成因。     

Anisotropic geodesics for live‐wire mesh segmentation

We present an interactive method for mesh segmentation that is inspired by the classical live‐wire interaction for image segmentation. The core contribution of the work is the definition and computation of wires on surfaces that are likely to lie at segment boundaries. We define wires as geodesics in a new tensor‐based anisotropic metric, which improves upon previous metrics in stability and feature‐awareness. We further introduce a simple but effective mesh embedding approach that allows geodesic paths in an anisotropic path to be computed efficiently using existing algorithms designed for Euclidean geodesics. Our tool is particularly suited for delineating segmentation boundaries that are aligned with features or curvature directions, and we demonstrate its use in creating artist‐guided segmentations.     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.     

Phase evolution and thermophysical properties of high-entropy RE2(Y0.2Yb0.2Nb0.2Ta0.2Ce0.2)2O7 oxides

Pursuing novel thermal barrier–coating materials with lower thermal conductivity and high-temperature stability can simultaneously improve the working efficiency and service temperature of a gas turbine. In this study, a series of high-entropy RE₂(Y_0.2Yb_0.2Nb_0.2Ta_0.2Ce_0.2)₂O₇ (RE = La, Nd, Sm, Gd, Dy, and Er) oxides were prepared though solid-state reaction. Through tuning the rare-earth cations, an order–disorder transition occurs from certain partially ordered weberite structure (C222₁) to disordered defective fluorite structure (Fm$\overline{3}$m). All the high-entropy RE₂(Y_0.2Yb_0.2Nb_0.2Ta_0.2Ce_0.2)₂O₇ oxides possess low thermal conductivity in the range of 0.91–1.34 W m⁻¹ K⁻¹ at room temperature, which can be attributed to increased lattice anharmonicity and disorder, resulting in additional phonon scattering. Herein, we proved that the incorporation of heterovalent cations at B-sites in high-entropy A₂B₂O₇ crystals is an effective strategy to reduce the thermal conductivity without compromising the decrease of oxygen vacancy. Moreover, the high-entropy RE₂(Y_0.2Yb_0.2Nb_0.2Ta_0.2Ce_0.2)₂O₇ oxides show the relatively higher thermal expansion coefficients of 10.3–10.7 × 10⁻⁶°C⁻¹ and excellent phase stability at elevated temperatures.     

剖析10 kV及以下电力线路设计

电力线路是电力系统的重要组成部分,其设计质量与电力系统的供电质量有着直接的关系。在设计电力线路时,需要综合考虑地形地貌、气候环境等各种因素。因此,加强电力线路的设计管理是十分必要的。     

凝结水再循环管道振动原因及减振措施

对比了福建省内某电厂一期、二期工程600 MW发电机组凝结水再循环管道的设计和布置,经过分析,得出了一期管道振动的原因。在二期设计中做出了一些改进,基本解决了凝结水再循环管道的振动问题。     

改性聚酰亚胺在摩托车中的应用

本研究选择了改性聚酰亚胺、改性聚甲醛、改性尼龙三种材料应用于摩托车衬套制品,进行了对比试验,结果表明:采用改性聚酰亚胺的衬套具有强度高、耐磨损、尺寸稳定性好等特点,完全达到该产品设计的要求。