Biochemical Conversion of Microalgae Biomass into Biofuel

Biofuel production via microalgae is a promising and sustainable alternative to replace the typical fossil fuel that is the main contributor to the global warming. However, for a cost‐effective biofuel production, further advanced research is still needed for large‐scale operation. This article is a tutorial review on conversion processes of microalgae into biofuel, with emphasis on biochemical conversion. The following topics are discussed: (i) microalgae biomass and its composition, (ii) thermochemical conversion, (iii) chemical conversion, and (iv) biochemical conversion. In addition, various aspects of anaerobic digestion, digester designs, and effects of operating conditions on the production of methane, bioethanol, and biohydrogen are discussed. The general kinetics of biomass conversion into biofuel is presented. This study suggests, if that biomass contains less than 50 % moisture, then it is recommended to use the direct combustion method; otherwise, biochemical conversion is the most suitable process to biofuel production.     

Effect of gamma irradiation on structural,morphological and optical properties of thermal spray pyrolysis deposited CuO thin film

This study reports the influences of gamma irradiation (GI) in the range of 20–100 kGy on CuO thin films via thermal spray pyrolysis technique on the glass substrates. The results demonstrate significant influences of GI on the crystallographic, microstructural and optical characteristics of CuO thin films. The obtained XRD results showed that the crystallinity of the films deteriorates by gradually decreasing crystallite size (from 59.13 to 46 nm) as applied gamma doses increases. However, the basic monoclinic crystal structure remains same. The dislocation density and lattice strain increased with the rise of GI absorbed dose due to the creation of defects. The values of number of crystallites per unit surface area increased as dose increased indicating the abundance of crystallization of nano CuO thin films. A UV–Vis–NIR spectrophotometer was utilized to determine the optical properties and obtained results indicated that the optical energy band gap (OBG) energies reduced from 2.00 to 1.72 eV as the doses increased from 0 to 100 kGy. No distinctions of the monoclinic phase of virgin CuO thin film have been perceived under applied absorbed doses, notwithstanding the slight deterioration of the crystallinity and narrowing the OBG.     

Radiation crosslinked polyvinyl alcohol/polyvinyl pyrrolidone/acrylic acid hydrogels: swelling,crosslinking and dye adsorption study

Iranian Polymer Journal - Hydrogels were produced from mixtures of polyvinyl alcohol (PVA), polyvinyl pyrrolidone (PVP), and acrylic acid (AAc) using γ-radiation at doses of 3, 7, and...     

System performances analysis of reservoir optimization–simulation model in application of artificial bee colony algorithm

In reservoir system operation, optimization is very much essential and the compatibility of different optimization techniques is essential to be checked by some performance checking indices. In this study, various types of performance-measuring index are used and compared to provide a complete knowledge on adopting different approaches. Here, the considered performance-measuring indicators will check the operation policy in terms of three different scenarios—how the method is efficient in achieving best results (reliability); how vulnerable the method is for different critical situation (vulnerability); and how capable it is to handle a failure of the model (resiliency). Therefore, the study proposed the artificial bee colony (ABC) optimization technique to develop an optimal water release policy for the well-known Aswan High Dam, Egypt. Particle swarm optimization, genetic algorithm and neural network-based stochastic dynamic programming are also used in a view of comparing model performances. A release curve is developed for every month as a guidance to the decision maker. Simulation has been done for each method using historical actual inflow data, and reliability, resiliency and vulnerability are measured. All model indicators proved that the release policy provided by ABC optimization outperforms in terms of achieving minimum water deficit, less waste of water and handling critical situations.

     

Network-level flexible pavement structural evaluation

The Kansas Department of Transportation has a comprehensive pavement management system known as network optimisation system (NOS). Annual condition surveys are conducted for NOS. Currently, the structural number (SN) of flexible pavements is computed using the American association of state highway and transportation officials equation based on the centre and fifth sensor deflections of a falling weight deflectometer (FWD). However, a rolling wheel deflectometer (RWD) can be used to collect deflection data at the network-level. This study was conducted to see whether the SN of flexible pavements can be obtained from this RWD deflection and NOS condition survey results. In this study, FWD deflection data, collected from 1998 to 2006, were analysed. Multiple regression analysis was done. The results showed that there is a negative relationship between SN and centre deflection. Equations can be used to calculate SN based on FWD (or RWD) centre deflections and network-level condition survey results. The SN is more sensitive to centre deflection than the total pavement thickness.     

Effects of metal support interaction on dry reforming of methane over Ni/Ce-Al2O3 catalysts

Dry (CO₂) reforming of methane is conducted over two newly synthesized Ni20/Ce-γAl₂O₃ and Ni20/Ce-meso-Al₂O₃ catalysts. The x-ray diffraction (XRD) patterns indicated that Ni20/Ce-meso-Al₂O₃ exhibits a better dispersion of nickel, while Ni20/Ce-γAl₂O₃ has larger amounts of nickel crystallites. The temperature programmed desorption (TPD) kinetics analysis indicated that Ni20/Ce-meso-Al₂O₃ had a lesser metal-support interaction than the Ni20/Ce-γAl₂O₃. The thermal gravimetric analysis (TGA) indicated that the incorporation of ceria into the Al₂O₃ matrix helps to stabilize Ni20/Ce-meso-Al₂O₃ during dry reforming of methane. The temperature programmed reduction (TPR) indicated that the synthesized catalysts were sufficiently reducible below 750 °C. A fixed bed reactor evaluation (at 750 °C) showed that both catalysts can facilitate methane reforming to syngas with minimal coking throughout the 30 hours time-on-stream (TOS). However, Ni20/Ce-meso-Al₂O₃ is more promising in terms of prolonged stability for dry reforming applications. Moreover, the syngas yield for Ni20/Ce-γAl₂O₃ is close to equilibrium prediction during the first 1 hour of reaction time.     

A Rapid Determination of Ergosterol in Grains Using Gas Chromatography–Mass Spectrometry Method Without Derivatization

Food Analytical Methods - A simple, rapid and sensitive GC-MS method using on-column injection was developed and validated to determine ergosterol (ERG) levels in maize and wheat. In this method,...     

Structural,mechanical, and electrical properties of carbon nanoparticles synthesized from diesel

We studied the elemental analysis, structural morphology, mechanical, and electrical properties of carbon nanoparticles synthesized from diesel. The spherical carbon particle size in the range of about 10 to 80 nm in diameter was observed in scanning electron microscope (SEM) studies that were identified by Atomic force microscopy (AFM) study as an aggregation of carbon particles of average size 2.5 nm. The surface rms of carbon nanoparticle thin film (CNTF) was measured directly by AFM and found 0.22 nm. The Derjaguin–Muller–Toporov (DMT) elastic modulus of carbon nanoparticles (CNPs) was measured by PeakForce QNM mode of AFM. The minimum and maximum elastic modulus was measured of 0.40 GPa and 43.89 GPa, respectively. The resistivity, conductivity, magneto resistance, mobility, and average Hall co-efficient were measured by “Ecopia Hall-effect measurement system” by four-point Van der Pauw approach at ambient condition. We demonstrated I–V characteristic at the Indium/CNTF thin film interface, which is accompanied by rectifying behavior.