铜基化合物的可见光催化研究进展

与传统贵金属光催化剂相比，铜基光催化剂具有价格低廉、绿色环保、反应条件温和、光催化活性可调节等优势，受到合成化学家们广泛关注。本文简述了铜基催化剂的光催化历史，回顾了近五年来铜基化合物在可见光催化领域的研究成果与进展，总结了铜基催化剂的独立光催化机理与协同光催化机理；简要阐述了铜催化剂在不同类型反应中的应用，重点讨论了铜(Ⅰ)催化剂在烯烃官能化、碳-碳偶联、碳-杂偶联、原位催化等反应中的应用研究，表明铜基化合物在光催化合成领域具有很大的应用潜力。对未来的研究工作进行了展望，指出拓展催化剂的反应适用性、探索催化剂的氧化还原能力、进一步开发催化剂在手性合成中的应用将是该领域的研究重点。     

高密度聚乙烯/铅硼复合材料屏蔽性能和力学性能研究

研究了高密度聚乙烯/铅硼复合材料的屏蔽性能和力学性能，通过屏蔽仿真比较了密度及碳化硼（B4C）含量对屏蔽性能的影响，通过试验比较了B4C含量对屏蔽性能、弯曲强度及冲击强度的影响。仿真结果表明,随聚乙烯/铅硼复合材料密度升高，快中子屏蔽性能下降，热中子屏蔽性能和γ屏蔽性能提高；保持聚乙烯/铅硼复合材料密度不变，随B4C含量的提高，中子屏蔽性能提高而γ屏蔽性能下降;实验数据表明,随B4C含量的升高，高密度聚乙烯/铅硼材料的快中子屏蔽性能、热中子屏蔽性能升高，γ屏蔽系数下降，冲击强度和弯曲强度下降明显，屏蔽性能测试结果和仿真结果规律性相符；综合仿真结果和实验数据表明，含B4C 2 %左右的高密度聚乙烯/铅硼复合材料同时具有较好的屏蔽性能和力学性能。     

Image Encryption Application of Chaotic Sequences Incorporating Quantum Keys

Machine Intelligence Research - This paper proposes an image encryption algorithm LQBPNN (logistic quantum and back propagation neural network) based on chaotic sequences incorporating quantum...     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

餐厨污水就地处理与中水回用工艺的探索与实践

以无锡某厂食堂污水处理及中水回用为例,探讨采用"隔油+混凝沉淀+A^2/O+MBR"工艺就地处理餐厨污水,并将出水回用于厂区冲厕可行性。经过78 d的调试,该工艺实现了餐厨污水中污染物的去除,COD小于50mg/L,NH4^+-N质量浓度小于5 mg/L,总氮小于10 mg/L,总磷小于0.5 mg/L,大肠杆菌数小于2个/L,基本满足中水回用要求。经计算吨水处理成本9.83元,含电费、药剂费、人工费、污泥处理费及膜更换费用。结合中水回用节省自来水后计算吨水处理综合成本为5.23元,大幅降低公司对市政供水的依赖,降低公司用水成本。     

Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。