Influence of mixing cycle on the degree of mixing of calcite‐filled polyethylene upon stretching

The mixing cycle‐dependent degree of dispersion and degree of mixing of a calcite (calcium carbonate) agglomerate in high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), and linear low‐density polyethylene (LLDPE) matrices upon stretching was investigated using three different techniques: mechanical property, morphological behavior, and image analyzer analyses. The mechanical properties analyzed in terms of the tensile strength and maximum elongation resulted in that the second mixing was the best for giving a better property for all systems except the LDPE system, which exhibited no significant difference between the second and third mixings. The morphological behavior of the three compounds were different, but no distinctive difference was observed to differentiate the degree of mixing from system to system. The number‐, weight‐, and z + 1‐average diameters of the air hole and the aspect ratio upon the stretching and mixing cycle were calculated to analyze the degree of mixing of the calcite‐filled composites. As a consequence, no difference in the average diameter of the air hole was obtained among the three systems, but the aspect ratios of the air hole varied significantly. Thus, the degree of dispersion and the degree of mixing may be influenced by the average calcite agglomerate size, the average diameter of the air hole, and the aspect ratio upon stretching and mixing cycles. Those factors would be formed by the difference in chemical characteristics upon various microstructures of polyethylene and its molecular weight and molecular weight distribution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 311–321, 2003     

The influence of filler on the emission properties and rheology of carbon nanotube paste

CNT paste consists of organic solution, inorganic binder and filler. Organic solution contains organic resins and solvent including surfactants which finely disperse CNTs. Filler affects surface morphology, electron emission property, viscosity, and rheological characteristics of CNT paste. We used different fillers such as silver and alumina in CNT paste for special function. The emission properties of CNT paste with silver are similar to those of CNT paste with alumina if filler portion is the same. From the scanning electron microscope (SEM) different morphologies of CNTs was observed depending on the type of filler. CNT paste which showed good emission property had vertically well-aligned CNTs on the surface after surface treatment using adhesive tape. We measured viscosity and rheological properties with rheometer RS600 from HAAKE. Emission property of CNT paste was evaluated in vacuum chamber of 10^{− 6} Torr with pulse generator and duty was 1/500.     

Cure kinetics and mechanical properties of the blend system of epoxy/diaminodiphenyl sulfone and amine terminated polyetherimide-carboxyl terminated poly(butadiene-co-acrylonitrile) block copolymer

The cure kinetics of blends of epoxy resin (4,4’-tetraglycidyl diaminodiphenyl methane; TGDDM)/curing agent (diaminodiphenyl sulfone; DDS) with ATPEI (amine terminated poly-etherimide) -CTBN (carboxyl terminated poly (butadiene-co-acrylonitrile)) block copolymer (AB type) were studied using differential scanning calorimetry under isothermal conditions to determine the reaction kinetic parameters such as activation energy and reaction constants. Final cure conversion decreased with increasing amount of AB in the blends. A diffusion controlled reaction was observed as the cure conversion increased, and the curing reaction was successfully analyzed by incorporating the diffusion control term in the rate equation for the epoxy/DDS/AB blends. The fracture toughness was improved to about 350% compared to that of the unmodified resin at 30% of AB block copolymer. This is attributed to the formation of co-continuous morphology between the epoxy phase and AB block copolymer phase. By increasing the amount of AB, the modulus of the cured blends decreased, which was due to the presence of CTBN rubbery phases.     

Effect of precipitation from tweed matrix on the mechanical properties in a metastable beta alloy of Ti-15-3

The effects of aging treatment on the microstructures and mechanical properties of a metastable beta titanium alloy Ti-15-3 (Ti−15V−3Al−3Sn-3Cr) have been investigated with hardness measurements, tensile test, and optical and electron microscopy. Precipitate-free beta structure with average grain size of about 56 μm was obtained after solution treatment at 800°C for 15 min followed by air cooling. Solution treated specimens were aged up to 800 h in the temperature range between 350 and 600°C. The morphology of the precipitates was varied significantly, depending on the aging temperature. The fine aggregates of α precipitates were dominant above 450°C. Peak hardness values were maintained up to 800 h at 500°C, which showed the superior thermal stability of α precipitates. Tensile strength increased up to 1600 MPa along with the decrease of elongation after aging at 350 and 400°C.     

Combined salience based person re-identification

Human eye perceives an object as the entity with global information and local information. Human salience is distinctive local information in matching pedestrians across disjoint camera views, and matching on overall foreground guarantees reliable and robust identification. In this paper, we propose a strategy for the matching of mean salience to identify pedestrians. Also, we consider that person re-identification based on the local single directional matching suffers from the variations of pose, illumination and overlapping, and propose a global bi-directional matching to solve the challenging problems of person re-identification. Furthermore, our matching of mean salience is tightly combined with the global bi-directional matching. Patch matching is utilized to handle the misalignment problem in pedestrian images. We test our feature and matching approaches in person re-identification scenario. Experimental results demonstrate that the mean salience and the global bi-directional matching have promising discriminative capability in comparison with other ones.     

Random Accessible Mesh Compression Using Mesh Chartification

Previous mesh compression techniques provide decent properties such as high compression ratio, progressive decoding, and out-of-core processing. However, only a few of them supports the random accessibility in decoding, which enables the details of any specific part to be available without decoding other parts. This paper proposes an effective framework for the random accessibility of mesh compression. The key component of the framework is a wire-net mesh constructed from a chartification of the given mesh. Charts are compressed separately for random access to mesh parts and a wire-net mesh provides an indexing and stitching structure for the compressed charts. Experimental results show that random accessibility can be achieved with competent compression ratio, which is only a little worse than single-rate and comparable to progressive encoding. To demonstrate the merits of the framework, we apply it to process huge meshes in an out-of-core manner, such as out-of-core rendering and out-of-core editing.