低应变动测与抽芯验桩结果对比分析

通过低应变反射波法与钻孔抽芯 2种检测方法的结果对比分析 ,验证低应变反射波法检测基桩的缺陷及位置的准确性 ,积累波形判别的经验。     

观测值序列的粗差探测方法

基于小波分析和未确知滤波理论，研究了对观测序列中粗差进行探测和剔除的方法，并结合实例进行了分析和比较，表明这2种方法得到的探测结果基本一致，均具备较好的应用价值。此外，进一步分析了2种方法的优点和局限性，为实际应用提供了有用的参考。根据2种处理方法的特点，提出了粗差探测的综合探测方法。     

一种PLC多参数现场设定与显示装置

在工业控制领域中,因生产工艺的改变需要现场修改一些控制参数才能满足实际控制要求.针对这种情况,本文介绍了一种基于三菱FX系列PLC的多参数设定与显示装置,对该装置的功能、硬件配置和实现方法进行了详细的讨论,采用结构化设计方法,完成了系统的设计,并给出了具体的梯形图程序.该装置操作简单、显示直观、运行稳定,不改变用户程序.对独立的PLC控制系统具有实际应用意义.     

Effect of Heat Treatment on Luminescent Properties of White Organic Light Emitting Device

The white organic light emitting device (OLED) with single-structure using a polymer blend as the light emitting layer is fabricated. Heat treatment is used to control the ratio between the intensities of main electroluminescent spectral peaks. The electroluminescent spectrum of our device is quite similar to that of white inorganic LED produced by Nichia Corporation after being annealed, and its turn-on voltage can be decreased by 1V.     

The Effect of the Charge Fluctuation of Dust Parti-cles on Ion-acoustic Wave Excited Through Ionization Instability

The effect of the charge fluctuation of dust particles on ion acoustic wave (IAW) excited through ionization instability was investigated. The hydrodynamic equations and linear time-dependent perturbation theory served as the starting point of theory, by which the dispersion relation and growth rate of the IAW were given. By comparing the results with the case of constant dust charges, it was found that the charge fluctuation of dust particles reduces the instability of the wave mode.     

Hydrogen Reduction and Microstructural Changes of ISF Sinter

The reduction rate and microstructural changes of imperial smelting furnace (ISF) sinter have been investigated by means of thermogravimetric analysis, X-ray difFraction (XRD), scanning electron microscope (SEM ), energy dispersive analysis of X-ray (EDAX) and optical microscope.It is demonstrated that the overall reaction rate of the reduction is influenced by temperature and hydrogen partial pressure in H2 /N2 gas mixtures. There are two distinct zones observed in the partially reduced sinter. The reduction of zincite proceeds predominantly in a narrow range between the two zones, while the reduction of tead oxide and silicate takes place throughout the sinter. The differences between zincite and lead oxide or silicate in reducibility are analysed by thermodynamlcs. The phase transformations and microstructural changes occurring during the reduction process are discussed     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。     

阻尼式限流器参数的设计选择

本文阐述阻尼式限流器参数设计选择和产品系列规划的依据原则，并结合实例说明实施步骤与方法，以有助于限流器的正确设计与选用。     

约束层阻尼夹芯板动态特性分析

本文给出了新的建立约束层阻尼薄板动力学模型的方法。粘弹性材料的本构关系随温度和频率变化,难以对粘弹结构进行动特性分析及控制研究,本文采用GHM方法描述弹性材料的本构关系,将粘弹性材料的动力特性描述与工程上最常用的有限元分析结合起来,建立了悬臂约束层阻尼板的动力学模型,计算了约束层阻尼夹芯悬臂板的模态参数,计算结果同其它方法相比,精度高且更接近于实验结果,同时与ANSYS5.5及NASTRAN70.7的计算结果基本一致,表明本文给出的方法是准确可靠的。