Improvement of RCA transistor using RTA annealing after theformation of interfacial oxide

A polysilicon emitter RCA transistor (an ultra-thin interfacial oxide layer exists between polysilicon and silicon emitter) is presented which can operate at 77 K for the first time. An ultra-thin (1.5 nm) interfacial oxide layer is grown deliberately between polysilicon and silicon emitter using RCA oxidation and excellent device stability is obtained after rapid thermal annealing (RTA) treatment in nitrogen atmosphere. The RCA transistor exhibits good electrical performance at very low temperature for an emitter area of 3 × 8 μm². The maximum toggle frequency of a 1:2 static divider is 1.2 GHz and 732 MHz at 300 K and 77 K, respectively     

An EM‐based adaptive multiple target tracking filter

Tracking targets of interest is one of the major research areas in radar surveillance systems. We formulate the problem as incomplete data estimation and apply EM to the MAP estimate. The resulting filter has a recursive structure analogous to the Kalman filter. The advantage is that the measurement‐update deals with multiple measurements in parallel and the parameter‐update estimates the system parameters on the fly. Experiments tracking separate targets in parallel show that tracking maintenance ratio of the proposed system is better than that of NNF and RMS position error is smaller than that of PDAF. Also, the system parameters are correctly obtained even from incorrect initial values. Copyright © 2001 John Wiley & Sons, Ltd.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

Monoacylglycerols derived from butter oil by Penicillium roquefortii in suspension cultures

Structural isomers of monoacylglycerols (monoglycerides, MAGs) were identified and compared after degradation of butter oil by two strains of Penicillium roquefortii and a commercial lipase from P roquefortii (EC 3.1.1.3) at pH 7.0 and 10 °C. The conditions were selected as they were comparable with those used in the manufacture of blue mould‐ripened cheese. The commercial lipase was selected to compare with the fungal strains in terms of acyl migration. Results showed that the main isomers formed by lipolysis with the commercial lipase were sn‐2 MAGs (64 mol%), whilst spores and emerging mycelia of P roquefortii produced mainly sn‐1(3) MAGs (83–90 mol%). The work reported here may lead to further assessment of different MAG structural isomers as natural preservatives in foods and dairy products. © 2002 Society of Chemical Industry     

Automatic conversion from lexical words to prosodic words for mandarin text-to-speech system

In real speech, not like lexical words (LWs), prosodic words (PWs) are basic rhythmic units. The naturalness of a Text-to-Speech (TTS) system is directly influenced by the segmentation of the PWs. Most of the PWs are the combination of several LWs. In this paper, three Lexical Combination Models are proposed to combine LWs into PWs, including a Directed Acyclic Graph Model, a Segmentation Model and a Markov Model (MM). To cope with the situation where some long LWs should be segmented into two or more PWs, a Lexical Split Model (LSM) is applied to the long LWs. Experimental results prove that relatively constant results with various training data can be obtained from a MM. The Transformation-Based Error Driven Learning (TBED) algorithm, for its high performance of individual property, is applied in combination with the MM to improve the precision of PW segmentation. Experiments show that among the three proposed models, the MM combined with TBED and LSM, leads to the best performance, in which a precision of 93.00% and a recall of 93.23% are achieved. The perception test indicates that by using PWs as the lowest prosodic units a speech sounds more natural and acceptable than by using LWs. This paper is supported by NSFC Project (60503071); 973 Natural Basic Research Program of China (2004CB318102); Postdoctor Science Foundation of P. R. China (20070420275).     

Improvement in hydrolytic procedure for GLC determination of non-indolyl glucosinolates in rapeseed as isothiocyanates

Some methods determine the non-indolyl glucosinolates content in rapeseed as their hydrolysates: the isothiocyanates and the oxazolidinethiones. These methods in their present form underestimate the amount of the glucosinolates content. In this investigation, a modified method was developed to give a better quantitative estimate, indicating a glucosinolate level five times that obtained by a typical existing method.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry