Ab initio calculations of the NO2 fission for CL-20 conformers

NO₂ fission is regarded to be the most important initial decomposition process of 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20). In this study, four CL-20 conformers based on the ε-CL-20 were obtained after the optimization at m062x/cc-pvtz level, and the bond length, bond order and bond dissociation energy of the N-N bonds were examined to investigate the stability of these bonds. In addition, the rate constants and activation energy of the NO₂ fission were evaluated using the microcanonical variational transition state theory (μVT). The calculation results have shown that N-N bonds in the case of pseudo-equatorial and axial of nitro groups are the most stable and the least stable, respectively, by evaluating the bond length, bond order and minimum energy path (MEP). The NO₂ fission rate constants are affected by not only the stability of N-N bonds but also the repulsion forces from the other nitro groups, and the fission process for pseudo-equatorial positioning of nitro groups is easier to be accelerated due to the increase of the repulsion forces. The decomposition of CL-20 conformer may mainly originate from the fission of the pseudo-equatorial positioning of nitro groups, especially for CL-20 III conformer because of the significant low activation energy.     

Study on Wettability and Corrosion Behavior of Al2O3 Doped Polyurea Coatings

Protection of Metals and Physical Chemistry of Surfaces - The Al2O3 powder was added as a filler to polyurea and the effect of doping amount on Shore hardness and wetting property were...     

离子液体水热法辅助合成稀土Ce掺杂ZnO纳米材料的制备及其应用研究

以1-甲基咪唑和氯代正丁烷为原料,合成1-丁基-3-甲基咪唑氯盐离子液体;以醋酸锌[Zn(Ac)2]、硫酸锌(ZnSO4)和氯化锌(ZnCl2)为锌源,在1-丁基-3-甲基咪唑氯盐离子液体和丙氨酸体系中与硝酸铈反应,经水热合成法制备得到Ce掺杂的纳米ZnO。采用扫描电子显微镜(SEM)、紫外-可见光吸收光谱(UV-Vis)、X射线衍射仪(XRD)、X射线光电子能谱分析(XPS)和红外光谱(FT-IR)对产品进行表征。以亚甲基蓝(MB)为目标降解物,采用UV-Vis检测,考察了Ce掺杂的纳米ZnO的光催化活性。研究表明,焙烧温度对光催化的晶体结构和光催化活性产生较大的影响;2%Ce/ZnO、焙烧温度为500℃、催化时间为30 min、亚甲基蓝用量0.05 g、pH值为10时降解率可达99.5%以上。     

Porous sunflower plate-like NiFe2O4/CoNi–S heterostructure as efficient electrocatalyst for overall water splitting

Constructing high-efficient and nonprecious electrocatalysts is of primary importance for improving the efficiency of water splitting. Herein, a novel sunflower plate-like NiFe₂O₄/CoNi–S nanosheet heterostructure was fabricated via facile hydrothermal and electrodeposition methods. The as-fabricated NiFe₂O₄/CoNi–S heterostructure array exhibits remarkable bifunctional catalytic activity and stability toward oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in alkaline media. It presents a small overpotential of 219 mV and 149 mV for OER and HER, respectively, to produce a current density of 10 mA cm^?2. More significantly, when the obtained electrodes are used as both the cathode and anode in an electrolyzer, a voltage of 1.57 V is gained at 10 mA cm^?2, with superior stability for 72 h. Such outstanding properties are ascribed to: the 3D porous network structure, which exposes more active sites and accelerates mass transfer and gas bubble emission; the high conductivity of CoNi–S, which provides faster charge transport and thus promotes the electrocatalytic reaction of the composites; and the effective interface engineering between NiFe₂O₄ (excellent performance for OER) and CoNi–S (high activity for HER), which leads to a shorter transport pathway and thus expedites electron transfer. This work provides a new strategy for designing efficient and inexpensive electrocatalysts for water splitting.     

Study on the Height of the Mining-Induced Water-Conducting Fracture Zone Under the Q 2l Loess Cover of the Jurassic Coal Seam in Northern Shaanxi,China

A method to calculate the height of a water-conducting fractured zone (HWCFZ) was developed based on the plate and shell theory, and the development of the HWCFZ in bedrock and Q2l loess strata is discussed in detail. First, the subsidence-deflection curve equation of the overlying stratum is theoretically derived, and then the ultimate deflection and free space height of rock strata are calculated. Moreover, the strata tensile strain is calculated by using integral calculus. In addition, the failure state of the rock is analyzed by comparing the theoretically calculated tensile strain with the experimentally measured yield tensile strain, allowing one to attain the maximum value of HWCFZ. This approach was tested at the Jinjitan coal mine; the theoretically predicted, experimentally measured, and numerically computed maximum HWCFZ values were 189.5, 187.3, and 188.5 m, respectively, demonstrating the accuracy of the proposed method. These results are highly significant for safe and environment-friendly coal mining in northwest Shaanxi, China.     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.