Modelling of effects of ultrastructural morphology on the hygroelastic properties of wood fibres

Wood fibres constitute the structural framework of e.g. wood, paper, board and composites, where stiffness and dimensional stability are of importance. An analytical modelling approach has been used for prediction of hygroelastic response, and assessment of the stresses in thick-walled cylinder models of wood fibres. A wood fibre was idealised as a multilayered hollow cylinder made of orthotropic material with helical orientation. The hygroelastic response of the layered assembly due to axisymmetric loading and moisture content changes was obtained by solving the corresponding boundary value problem of elasticity. A simple solution scheme based on the state space approach and the transfer matrix method was employed. This was combined with an analytical ultrastructural homogenisation method, used to link hygroelastic properties of constituent wood polymers to properties of each layer. Predicted hygroelastic response captured experimentally measured behaviour. Fibres that were constrained not to twist showed a stiffer response than fibres allowed twisting under uniaxial loading. It was also shown that the ultrastructure, i.e. the microfibril angle, will control the hygroexpansion in the same way as it controls the compliance of the cell wall. Qualitative failure trends comparable with experimental observations could be established with stress analysis and a simple plane-stress failure criterion.     

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate have been carried out. The dielectric constant has been measured as a function of frequency in the range 2 kHz–1 MHz and temperature range 30–300 °C. The dielectric constant increases with temperature, attains a peak near 215 °C, and then decreases as the temperature exceeds 215 °C. The dielectric anomaly at 215 °C is suggested to be due to phase transition brought about in the material. The dielectric behaviour of the material is correlated with the results on thermal analysis. Thermogravimetric and differential thermal analysis have been used to study the thermal characteristics of the material. The experimental results show that the material is thermally stable up to 200 °C. The decomposition process occurs in two stages until ytterbium oxide is formed at 700 °C. The non-isothermal kinetic parameters e.g., activation energy and the frequency factor have been evaluated for each stage of thermal decomposition by using the integral method, applying the Coats–Redfern approximation.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

A review on the synthesis of in situ aluminum based composites by thermal,mechanical and mechanical–thermal activation of chemical reactions

The aim of the present paper is to review the recent progress in the synthesis of in situ particle reinforced aluminum composites using thermal, mechanical and combined mechanical-thermal activation of aluminothermic reduction reactions. The combination of combustion synthesis (CS) and mechanosynthesis (MS) is the most recent development in the processing of advanced materials like micro and nano aluminum based composites. The combined mechanical thermal synthesis (MTS) has widened the possibilities for both CS and MS. MTS holds great potential for commercial viability and offers exciting processing route for the synthesis of advanced materials. Enhanced reaction kinetics and extended concentration limits in MTS are demonstrated by illustrating the synthesis of aluminum based nanocomposite involving Al–CeO₂.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Preparation of gold nanoparticles (GNP) aqueous suspensions by a new method involving Tiron

A new method is proposed to produce gold nanoparticles (GNP) by in situ reduction of a gold salt dissolved in water. The reducing agent used is Tiron instead of the citrate anion most often mentioned in literature. The influence of various parameters has been investigated, such as the content of Tiron with respect to that of the precursor of gold HAuCl₄, or the initial pH of the solution after mixing of reactants. It is shown that Tiron also exerts a positive influence as a dispersant, which impedes agglomeration of gold nanoparticles. The typical average size of GNP synthesized in the present work is close to 7 nm.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.