Scintillation Properties of 6LiI(Eu) in Cryogenic Temperatures

We measured emission wavelength spectra, scintillation decay time and scintillation light yield of ⁶LiI(Eu) in the temperature range from 4.2?K to 300?K. We observed that the scintillation decay time was almost constant (1.3?μs) below 100?K. At 4.2?K the light yield was found to increase to 6 times higher than that at 300?K. The ⁶LiI(Eu) is expected to be utilized for spectroscopic measurement of fast neutrons by operating at 4.2?K.     

Structural,mechanical, and electrical properties of carbon nanoparticles synthesized from diesel

We studied the elemental analysis, structural morphology, mechanical, and electrical properties of carbon nanoparticles synthesized from diesel. The spherical carbon particle size in the range of about 10 to 80 nm in diameter was observed in scanning electron microscope (SEM) studies that were identified by Atomic force microscopy (AFM) study as an aggregation of carbon particles of average size 2.5 nm. The surface rms of carbon nanoparticle thin film (CNTF) was measured directly by AFM and found 0.22 nm. The Derjaguin–Muller–Toporov (DMT) elastic modulus of carbon nanoparticles (CNPs) was measured by PeakForce QNM mode of AFM. The minimum and maximum elastic modulus was measured of 0.40 GPa and 43.89 GPa, respectively. The resistivity, conductivity, magneto resistance, mobility, and average Hall co-efficient were measured by “Ecopia Hall-effect measurement system” by four-point Van der Pauw approach at ambient condition. We demonstrated I–V characteristic at the Indium/CNTF thin film interface, which is accompanied by rectifying behavior.     

Possibility of Japanese Cedar Pollen Causing False Positives in the Deep Mycosis Test

Because Japanese cedar pollen (JCP) contains beta-1,3-d-glucan (BG), there is concern that its lingering presence in the atmosphere, especially during its scattering period, may cause false positives in the factor-G-based Limulus amebocyte lysate (LAL) assay used to test for deep mycosis (i.e., G-test). Hence, we examined whether the LAL assay would react positively with substances contained in JCP by using the G-test to measure JCP particles and extracts. BG was purified from the JCP extract on a BG-specific affinity column, and the percentage extractability was measured using three different BG-specific quantitative methods. The G-test detected 0.4 pg BG in a single JCP particle and 10 fg from a single particle in the extract. The percentage extractability of JCP-derived BG was not significantly different among the three quantitative methods. As the JCP particles should technically have been removed during serum separation, they should be less likely to be a direct false-positive factor. However, given that the LAL-assay-positive substances in the JCP extract were not distinguishable by the three BG-specific quantitative methods, we conclude that they may cause the background to rise. Therefore, in Japan false positives arising from JCP contamination should be considered when testing patients for deep mycosis.     

Trend Curve Optimal Control Model for Optimizing Pavement Maintenance Strategies Consisting of Various Treatments

Abstract: Most literature on pavement maintenance optimization for the case of continuous time assumes only one type of maintenance treatment, such as overlay, to be applicable and demonstrates solution procedures with simple cases of limited scopes. However, as overlays may not always be appropriate, depending on traffic loading/pavement situations, the objective of this article is to propose an optimization approach based on the trend curve optimal control model, to obtain optimal strategies possibly consisting of overlay, resealing, and reconstruction. The applicability of the solution procedure is demonstrated with several cases representing a variety of traffic loading/pavement situations. The solutions indicate that an optimal maintenance strategy can consist of multiple types of treatments depending on the situation, illustrating the versatility of the proposed procedure.     

Properties of Hopfield model with the zero-order synaptic decay

In this paper, we investigate the effect of synaptogenesis on memories in the brain, using the abstract-associative memory model, Hopfield model with the zero-order synaptic decay. Using the numerical simulation, we demonstrate the possibility that synaptogenesis plays a role in maintaining recent memories embedded in the network while avoiding overloading. For the network consisting of 1000 units, it turned out that the minimum decay rate to avoid overloading is 0.02, and the optimal decay rate to maximize the storage capacity is 0.08. We also show that the average numbers of replacement synapses at each learning step corresponding to these two values are 1187 and 21024, respectively.     

Rupture nucleation on an interface with a power-law relation between stress and displacement discontinuity

We consider rupture initiation and instability on a displacement-weakening interface. It is assumed to follow a power-law relation between a component of displacement discontinuity (whether tensile opening in mode I or shear slippage in modes II or III) and the reduction from peak strength of a corresponding component of stress (normal or shear stress) on the interface. That is, the stress decrease from peak strength, as the interface discontinuity develops, is assumed to be proportional to displacement-discontinuity to some exponent n > 0. The study is done in the 2D context of plane or anti-plane strain, for an initially coherent interface which is subjected to a locally peaked “loading” stress which increases quasi-statically in time. We seek to establish the instability point, when no further quasi-static solution exists for growth of the ruptured zone along the interface, so that dynamic rupture ensues. We have previously addressed the case of linear displacement-weakening (n = 1), and proven the remarkable result that for an unbounded solid, the length of the displacement-weakening zone along the interface at instability is universal, in the sense of being independent of the detailed spatial distribution of the locally peaked loading stress. Present results show that such universality does not apply when n differs from 1. Also, if n < 2/3, there is no phase of initially quasi-static enlargement of the rupturing zone; instead instability will occur as soon as the maximum value of the loading stress reaches the peak strength. We first employ an energy approach to give a Rayleigh–Ritz approximation for the dependence of quasi-static rupture length and maximum displacement-discontinuity on the loading stress distribution of a quadratic form. Results, depending on curvature of the loading distribution, show that qualitative features of the displacement-discontinuity development are significantly controlled by n, with the transition noted at n = 2/3. Predictions of the simple energy approach are in reasonable quantitative agreement with full numerical solutions and give qualitative features correctly.     

Reappraisal of loading rate effects on sand behavior in view of seismic design for pile foundation

This study re-visits the effects of loading rate on sand behavior in view of seismic design of pile foundation. Based on an extensive literature review covering both element testing and model testing, the paper summarizes the current understanding of the loading rate effects. The paper then describes the development of test apparatus used in this study and presents the data obtained from a series of monotonically increasing triaxial compression tests on Toyoura sand, varying the strain rate in the range of 0.005%/s to 250%/s. A total of 36 tests were conducted on dry and saturated sand, both under drained and undrained conditions with two confining pressures. The experimental results confirm that the soil strength and the soil stiffness increase as the strain rate increase. This paper also concludes that the internal friction angle and deformation modulus increase when the strain rate is high. The implications of the loading rate effect on pile foundation design are then presented.     

Advantage of Sodium Polyoxyethylene Lauryl Ether Carboxylate as a Mild Cleansing Agent

Five anionic surfactants widely used in commercial skin cleansers were studied: sodium polyoxyethylene lauryl ether carboxylate (EC), sodium polyoxyethylene alkyl ether sulfate (ES), sodium dodecyl sulfate, potassium laurate, and N-cocoyl-l-glutamic acid monosodium salt. The amount of surfactant from aqueous solution adsorbed into the stratum corneum (SC), the degree of SC swelling, the change of the secondary structure of SC proteins (denaturation). The surface tension of surfactant–zein mixed solutions, and the solubilization behavior of zein were measured. Results showed that EC had the lowest adsorption into SC, the lowest SC swelling, and lowest denaturation of SC proteins. Low interactions between surfactants and SC proteins were also observed for EC/ES mixture solutions as well as. Mixing EC with ES good foaming performance. The EC/ES mixture, at about 1:1 ratio, is an excellent surfactant system for skin cleanser applications having cleansing characteristics and mildness to the skin.     

Basic information on new regulatory criteria requiring on-site emergency preparedness for accelerator facilities in Japan

For basic information on new regulatory criteria, the dose rate around a thick target bombarded by proton, electron, or carbon beam having incident energy of 10 MeV–50 GeV (per nucleon in case of carbon) was simulated using the PHITS Monte Carlo code. Based on this simulation, the benchmark which is ‘1 Sv/h at 1 m away from the beam line’ assuming 1% beam loss was evaluated, and compared with the criteria in France and Canada. Based on this evaluation, a new regulatory criteria has been established for requiring on-site emergency preparedness for accelerator facilities in Japan, which is required for the ion accelerator beyond the ion beam of 100 MeV/nucleon and 0.5 kW beam power, and the electron accelerator beyond the electron beam of 50 MeV energy and 1 kW beam power.