Preparation and properties of branched polybutylenesuccinate

To obtain long branched polybutylene succinate (PBS), modified PBSs were prepared by introducing a branching agent, trimethylol propane (TMP), to the polycondensation system of succinic acid and 1,4‐butanediol. Molecular parameters such as absolute molecular weight and root‐mean‐square (RMS) radius of the modified PBSs were measured by gel permeation chromatography (GPC) with a multiangle laser light‐scattering (MALLS) detector. The RMS radius of TMP05, PBS prepared by incorporating 0.5 wt % TMP during polycondensation, was the smallest of all PBSs tested at the same molecular weight. The notable shear thinning and much reduced loss tangent for TMP05 qualitatively supported the difference in their molecular structures predicted by GPC. The analytical results indicated that introducing 0.5 wt % TMP produced PBS with chain branches long enough to produce molecular entanglements. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1388–1394, 2001     

Full-rate cooperative communications with spatial diversity for half-duplex uplink relay channels

This paper proposes a full-rate cooperative communication technique with spatial diversity for single-carrier transmissions. In order to achieve both the spatial diversity and the full-rate, data streams are simultaneously transmitted through all direct and relay channels with different phase rotation and cyclic delay patterns. The phase rotation and cyclic delay patterns are derived in the sense of minimizing interlayer interference and a corresponding destination structure is presented for decoupling each layer at the destination. Simulation results show that the proposed technique achieves spatial diversity without sacrificing spectral efficiency and outperforms conventional full-rate cooperative communication techniques.     

CdSe-sensitized inorganic–organic heterojunction solar cells: The effect of molecular dipole interface modification and surface passivation

CdSe-sensitized heterojunction solar cells composed of mesoscopic TiO₂/CdSe/P3HT (poly-3-hexylthiophene) were constructed, and the negative molecular dipole of 4-methoxybenzenethiol (MBT) and the ZnS passivation layer were used as interface modifiers to improve device performance. Through the interface modification between TiO₂/CdSe and P3HT using MBT and by ZnS surface passivation, the power conversion efficiency of the modified solar cell was greatly enhanced from 1.02% to 1.62% under 1 sun illumination.     

In-Flight Particle Measurement of Alkali-Free Glass Raw Materials in 12-Phase AC Arc Plasma

In-flight particle measurements of the surface temperature and velocity are important for understanding of melting behavior of glass particles during in-flight melting by multi-phase AC arc plasma. However, the use of optical pyrometry for particle surface temperature has inevitable uncertainties due to non-thermal emissions signals from the plasma plume. This work presents spectroscopic measurements of the non-thermal signals which were found to be caused mainly by the plasma emissions scattered by the particles and the radiation emitted by vapor. After that, the accuracy of thermal radiation measurement was estimated and surface temperature of in-flight glass particle was corrected.     

Shape-controlled fabrication of polypyrrole microstructures by replicating organic crystals through electrostatic interactions

Polypyrrole (PPy) microstructures with diverse shapes were synthesized in an aqueous inorganic salt medium including organic crystals and pyrrole (Py). A series of sulfobenzoic acid salt forms with various cations (K⁺, Na⁺, Li⁺, NH₄⁺) in different positions (para, meta, ortho) of the sulfonate group on the benzene ring were used to form organic crystals as sacrificial templates. Using these crystals, we produced five different shapes of PPy microstructures (hexagonal microplates, curled nanofibers, lozenge-shaped microplates, rigid rods, parallelogram microplates), which replicated the shapes of the organic crystal templates through electrostatic interaction between the anionic crystal surfaces and the cationic PPy chains. In contrast, PPy that was polymerized without crystals showed bulky agglomerates of 200-500 nm size. The electrical properties were dictated by the molecular structures of the organic salt molecules used. While the highest conductivity (200.3 Scm⁻¹) was observed in PPy using crystals of para-linked 4-sulfobenzoic acid monopotassium salt, the lowest conductivity (0.8 Scm⁻¹) was observed in PPy prepared in the presence of crystals of ortho-linked 2-sulfobenzoic acid monoammonium salt.     

The electrochemical behavior of an enzyme biosensor electrode using an oxyfluorinated pitch-based carbon

A glucose sensor electrode was prepared by thermally treating a pitch-based carbon material. Oxyfluorination was used to modify the surface of the prepared carbon to induce the formation of hydrophilic functional groups. A glucose oxidase enzyme was effectively loaded onto the surface of the oxyfluorinated carbon and was more sensitive in glucose sensing because of the effects of the improved interfacial affinity between the electrode and the glucose oxidase. The introduced hydrophilic functional groups were examined using XPS analysis. In current–voltage measurements, a higher current was observed in the samples prepared with a higher oxygen content. In addition, a clear redox peak was observed in the surface modified samples. These results can be attributed to efficient electrical resistance measurement by easy electron transfer during glucose sensing. An efficient glucose sensor electrode was prepared using pitch-based carbon, which has beneficial electrical properties, and oxyfluorination, which improves the surface interface.     

Synthesis of ultra-thin polypyrrole nanosheets for chemical sensor applications

Ultra-thin polypyrrole nanosheets (UPNSs) are fabricated by organic crystal surface-induced polymerization (OCSP) of pyrrole in an aqueous suspension containing hydrated crystals of sodium decylsulfonate (C₁₀SO₃Na) below the Krafft temperature using FeCl₃ as an oxidant. The hydrated C₁₀SO₃Na crystals are used as templates through electrostatic binding of the cationic polypyrrole (PPy) chains oxidized by Fe(III) ions on the anionic C₁₀SO₃Na crystal surface. The resulting UPNSs have a single layer thickness of ∼21 nm, widths between 2 and 6 μm, and lengths greater than 10 μm. The UPNSs are composed of a single continuous PPy domain. Moreover, the UPNSs exhibit higher conductivity (30.6 Scm⁻¹) and longer conjugation lengths than the PPy nanoparticles (2.4 Scm⁻¹) prepared using emulsion polymerization. We systematically investigate the UPNSs as gas sensors for detecting and quantifying toxic gases such as HCl and NH₃. The UPNSs exhibit much higher gas sensitivity and faster response times compared with the PPy nanoparticles.     

Effects of Two-stage Heat Treatment on Delayed Coke and Study of Their Surface Texture Characteristics

In the present study, surface texture features and chemical properties of two types of cokes, made from coal tar by either 1-stage heat treatment or 2-stage heat treatment, were researched. The relationship between surface texture characteristics and the chemical properties was identified through molecular weight distribution, insolubility of coal tar, weight loss with temperature increase, coking yield, and polarized light microscope analysis. Rapidly cleared anisotropy texture in cokes was observed in accordance with the coking temperature rise. Quinoline insolubility and toluene insolubility of coal tar increased with a corresponding increases in coking temperature. In particular, the cokes produced by the 2-stage heat treatment (2S-C) showed surface structure of needle cokes at a temperature approximately 50°C lower than the 1-stage heat treatment (1S-C). Additionally, the coking yield of 2S-C increased by approximately 14% in comparison with 1S-C.