Denatured-jacalin derivatives with selective recognition for O-linked glycosides (ST,T, Tn,and STn Type) on IgA1 hinge region

Immunoglobulin A1 (IgA1) concentration in the plasma of patients with IgA nephropathy (IgAN) as the cause of renal failure is higher than that in the plasma of normal controls. IgA1 with abnormal sugars is considered to deposit in the glomerular mesangium, aggravating nephritis in IgAN. Jacalin is a lectin that recognizes sugars on IgA1. However, its selective-recognition for normal-type (ST type, NeuAc-α(2,3)-Gal-β(1,3)-GalNAc) and abnormal-type (T type, Gal-β(1,3)-GalNAc; Tn type, GalNAc; STn type, NeuAc-α(2,6)-GalNAc) sugars α-O-linked to serine/threonine in IgA1 is weak. Therefore, jacalin cannot be used for recognizing specific sugar types on IgA1. We attempted to develop a new recognition method for specific sugar types on IgA1 by utilizing the multirecognition capability of jacalin. Its binding abilities were regulated by heat denaturation with suitable template sugar (galactose or N-acetylgalactosamine). Further, we successfully prepared denatured-jacalin derivatives, which recognized ST-/T-type sugars on IgA1, by sugar-immobilized affinity chromatography. Enzyme-linked immunosorbent assay of denatured-jacalin derivatives, showed the ratios of abnormal sugars on IgA1 in the plasma of IgAN patients and normal controls to be approximately 60% and 20%, respectively. The results proved that profiling of sugar types in IgAN can successfully be performed by solely using jacalin derivatives.     

Deposition of DLC film with adhesive W-DLC layer on stainless steel and its tribological properties

Tribological properties of a diamond-like carbon (DLC) coating with an adhesive tungsten-containing DLC (W-DLC) layer were investigated. The coatings were deposited onto AISI316L steel substrates and Si wafers using plasma enhanced chemical vapor deposition and tungsten co-sputtering of the metal target. Methane and argon gases were used as the precursor of the coatings. In this study, three types of coatings were evaluated: DLC/W-DLC on AISI316L (DLC-1), DLC/W-DLC on Si wafer (DLC-2), and DLC on Si wafer (DLC-3). The structural characterizations were performed by transmission electron microscopy and tapping mode atomic force microscopy. At the boundary between the W-DLC layer and the AISI316L substrate, microscopic decohesion or delamination was not observed. The surface roughness of the DLC-1 coating was greater than that of the DLC-2 coating. This feature was derived from the surface roughness of the initial surface of the AISI316L substrate. Friction tests were performed using a rotation-type ball-on-flat configuration tribometer. The observed friction of the DLC-1 coating was unstable compared with the DLC-2 or DLC-3 coatings. This was due to wear debris which had risen to the friction surface resulting in unstable friction on the DLC-1 coating. During the friction studies, the top DLC layer was removed from the adhesive W-DLC layer because the adhesive strength at this part was not enough. In order to achieve the low and stable friction of the DLC coating with the W-DLC layer on AISI316L, it is necessary to improve the smoothness of the surface and the adhesion between the DLC coating and the W-DLC layer.     

A 65 nm Single-Chip Application and Dual-Mode Baseband Processor With Partial Clock Activation and IP-MMU

Supporting both WCDMA with HSDPA and GSM/GPRS/EDGE, the 9.3 times 9.3 mm² SoC fabricated in triple-Vth 65 nm CMOS, has three CPU cores and 20 separate power domains. Unused power domains can be powered down to reduce the leakage power. Partial clock activation scheme especially focused on music playback scene dynamically stops a PLL and clock trees when not necessary and reduces power consumption from 33.6 mW to 19.6 mW. IP-MMU translates virtual address to physical address for 18 hardware-IPs and virtual address space can be allocated when necessary and can be freed after its operation, reducing external memory by 43 MB. Video performance of D1 (720 times 520) size with 30 frames per second for MPEG/AVC decoding and encoding can be achieved under mixed virtual and physical address usage.     

Study of drive system for linear induction motor using magnetic energy recovery switch

This paper proposes a power supply suitable for driving linear induction motors. The power supply consists of a voltage source inverter (VSI) and a magnetic energy recovery switch (MERS). Circuit configuration and operation principles of the power supply are described. Power factor correction by MERS can increase the output power. Technical advantages of using MERS compared with increasing the rated voltage of VSI are discussed. Some experiments with a linear induction motor were conducted. The results confirm that MERS can reduce the capacity of the VSI or increase the output with the same VSI capacity. The number of devices and magnitude of losses are evaluated on a large‐scale drive system. A half‐bridge type of MERS is provided and discussed. The half‐bridge MERS mitigates disadvantages of using MERS. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 169(4): 65–74, 2009; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20832     

Application of SPRT to an image data sequence for a remote monitoring system

Recently, remote monitoring camera systems have been widely used for security. In such systems, one important function is that the system automatically detects any change in the scenes from the monitoring cameras. In wireless remote monitoring camera systems, the images of the scenes are generally transmitted as compressed data (e.g., JPEG file), because of the capacity of the wireless channel. This article shows the automated detection of the change point in time-series data of compressed JPEG file quantity (Kbytes) from the monitoring camera by applying the sequential probabilistic ratio test (SPRT) and the Chow test, which is well known as a standard method for detecting structural change in time-series data.     

Coupling Analysis of GaAs-Based Microdisk Lasers With Different External Claddings

In this paper, we analyze the coupling of light from a GaAs microdisk laser into a waveguide. Starting from an air cladding, we examine several configurations to couple light into the waveguide with different cladding structures aimed to foster light coupling into the waveguide: photonic crystal and metallic (plasmonic cladding). In these coupling schemes, we tried to optimize the coupling of the emitted light into the waveguide, while maintaining a reasonable quality factor to allow the lasing operation of the device. We show that a plasmonic layer, introduced beside the waveguide can lead to a significant improvement in the coupling efficiency, reaching an efficiency close to 80%.     

Decay of material properties of degraded MEA caused by repeated cold starts under subzero conditions in polymer electrolyte fuel cells

This study investigated the characteristics of cell performance degradation, decline of component performance, and changes in the properties of membrane electrode assembly materials caused by repeated cold starts under a subzero condition of ?30 °C. It was made clear that functional decay appeared mainly at the cathode due to increased proton conductive impedance and reduction of reactivity of the electrode catalyst. Among the cathode components, an increase in proton conductive impedance in the cathode electrolyte was dominant. Furthermore, the application of ion chromatography and a newly developed proton‐induced gamma‐ray emission method to measure fluorine in the off‐gas drain revealed that decomposition of the electrolyte was dominant in the cathode catalyst layer. A decrease in fluorine in the cathode electrolyte measured by fluorine‐19 nuclear magnetic resonance confirmed this decomposition. A hypothesis is also presented concerning the cause of the performance degradation. © 2012 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20394