改性Kevlar纳米纤维对天然橡胶耐溶剂性能和交联密度的影响（英文）

制备了改性Kevlar纳米纤维(m-KNFs)填充天然橡胶硫化胶,研究了不同用量的m-KNFs对天然橡胶耐溶剂性能和交联密度的影响。结果表明,m-KNFs可有效增强天然橡胶的耐溶剂性能,当m-KNFs的用量为7份时,天然橡胶的溶剂吸附常数比未填充时降低了11. 7%。同时,天然橡胶的交联密度随着m-KNFs用量的增加而增大。     

3-三氟甲基-5,6,7,8-四氢-1,2,4-三唑[4,3-α]吡嗪盐酸盐的合成

乙二胺与氯乙酸乙酯经取代、环合反应制得2-哌嗪酮,2-哌嗪酮与Boc酸酐进行氨基保护反应后,再与五硫化二磷进行硫代反应制得4-(N-叔丁氧羰基)-2-哌嗪硫酮,其与三氟乙酰肼经取代、环合、脱叔丁氧羰基成盐,得标题化合物,总收率为45.7%(以氯乙酸乙酯计)。为磷酸西他列汀中间体的工业化生产提供了一条较理想的工艺路线。     

工艺参数对超声辅助脉冲电沉积镍-氮化钛复合镀层的影响

在45钢表面以超声波辅助脉冲电沉积制备Ni-TiN复合镀层。研究了平均阴极电流密度、脉冲占空比、超声功率和TiN粒子(平均直径20~30 nm)添加量对复合镀层的TiN粒子含量和显微硬度的影响。得到较优的工艺参数为:NiSO4ꞏ6H2O 300 g/L,NiCl2ꞏ6H2O 30 g/L,H3BO330 g/L,十二烷基硫酸钠0.3 g/L,TiN 25 g/L,pH 4.1~4.3,温度40°C,平均阴极电流密度4 A/dm2,脉冲占空比40%,脉冲频率1000 Hz,超声功率300 W,机械搅拌速率200 r/min,时间60 min。该条件下所得Ni-TiN复合镀层的TiN质量分数为8.35%,显微硬度为819 HV,表面平整、致密,晶粒尺寸均匀。     

一种装备反应时间测量装置设计与应用

为了对激光信号探测器输出的TTL信号和其他设备输出的差分信号时间间隔进行测量,设计了一种以AT89S2051单片机为主控制器,以CPLD复杂可编程逻辑器件EPM7128S为辅助控制器的反应时间测量装置。利用CPLD编程实现方便灵活的特点,简化电路设计,降低了成本。装置设置两路TTL信号输入接口、两路差分信号输入接口和两路脉冲信号输出接口,可按实际使用需要对反应时间起始与截止信号输入通道进行选择和设置,将测量结果显示输出。经检测和使用证明,装置操作简便、测量准确、运行稳定,能满足有关时间参数的测量使用,可向有关时间参数测量应用拓展。     

N,N'-二(2-羟丙基)哌嗪-硫酸钠-水三元体系相平衡测定与计算

采用等温溶解平衡法测定N,N′-二(2-羟丙基)哌嗪(HPP)?Na2SO4?H2O三元体系在273.15和298.15 K下的相平衡数据，采用湿渣法测定其平衡固相数据，绘制等温相图。用改进的单组分电解质Pitzer方程计算该体系中Na2SO4和Na2SO4?10H2O的溶解平衡常数，并对相平衡数据进行理论计算。结果表明，273.15 K时存在3个结晶区，298.15 K时存在4个结晶区。HPP的存在降低了Na2SO4和Na2SO4?10H2O的相转变温度，使298.15 K下的相图中存在Na2SO4的结晶区域，且273.15和298.15 K的相图中不存在纯HPP的结晶区域。理论计算与实验数据的均方根偏差不高于0.0290，表明相平衡数据计算值与实验值较吻合，证实了改进的单组分电解质Pitzer方程适用于该体系计算。     

齐大山铁矿南帮含水构造带探测研究

为解决采空区突发涌水给矿山安全生产带来的安全威胁,以齐大山铁矿为研究对象,以高密度电阻率法含水构造带理论模型的正演模拟研究为基础,运用高密度电阻率法对采场南帮含水构造带的异常范围进行了圈定;运用瞬变电磁法进行了二次探测,并对高密度电阻率法所圈定的异常范围进行了验证。研究表明:含水构造带显示为低阻异常特征,在高密度电阻率法探测成果图中显示的两处低阻异常与含水构造带理论模型的正演模拟结果一致;同时,在瞬变电磁法探测成果图中显示的低阻区域均在高密度电阻率法所圈定的低阻异常范围内,二者相互验证,这两处低阻异常均为含水构造带的地球物理异常特征的显示,表明采用高密度电阻率法和瞬变电磁法组合识别技术可实现对隐伏含水构造带的先导性探测。     

Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

喷雾干燥法制备材料论文的指导方案

喷雾干燥技术的突出特点是将液态物料瞬时干燥成固体粉末或者颗粒。我们课题组在指导本科生毕业论文中采用了喷雾干燥法制备碳包覆铌酸钛材料的实验,在实验过程中我们发现了一些问题,如喷雾干燥机需要适当预热、喷头容易堵赛和收集原料不干等问题。我们就以上问题进提出了相应的对策,这加深了本科生对喷雾干燥实验的体会和认识,培养了学生在独自实验时面对问题解决问题的能力。