Analysis and characterization of traveling-wave electrode in electroabsorption modulator for radio-on-fiber application

Comparing with a lumped electroabsorption modulator (EAM), we show the merits of a long EAM with traveling-wave electrode with high radio-frequency (RF) gain that could be used in high-frequency analog application. By terminating the RF output port with the characteristic impedance of 30 /spl Omega/, the device exhibited a large enhancement of 6 dB above 10 GHz in the electrical-to-optical response and a wide fractional bandwidth as estimated from simulation. In addition, an input impedance matching circuit of stub embedded on the device chip was found to be very effective for improving RF characteristics in the narrow band of frequency.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

Spectrally stable Er-fiber laser for application in phase-sensitive optical time-domain reflectometry

A high degree of frequency stability in an Er-fiber laser with the Fabry-Perot configuration was achieved using a long (25-km) optical-feedback loop. The frequency-drift rate was determined to be <1 MHz/min by observing temporal fringes in an unbalanced Mach-Zehnder interferometer. Instantaneous linewidth measured with a delayed self-heterodyne interferometer was less than the 3-kHz resolution limit. The laser was utilized in an optical time-domain reflectometry experiment to detect and locate a time-varying phase perturbation applied to an optical fiber.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Accurate higher-order analytical approximate solutions to nonconservative nonlinear oscillators and application to van der Pol damped oscillators

In general, this paper deals with general nonlinear oscillations of a nonconservative and single degree-of-freedom system with odd nonlinearity and, in particular, it presents accurate higher-order analytical approximate solutions to van der Pol damped nonlinear oscillators having odd nonlinearity and the Rayleigh equation. By combining the linearization of the governing equation with harmonic balancing and the method of averaging, we establish accurate analytical approximate solutions for the general weakly damped nonlinear systems. Unlike the classical harmonic balance method, simple linear algebraic equations instead of nonlinear algebraic equations are obtained upon linearization prior to harmonic balancing. The combination of these two methods results in very accurate transient response of the periodic solution. In addition and for the first time, this paper also presents a method for deducing fourth-, fifth- and higher-order linearized governing equations from the lower-order equations without the requirement of formulating the problem from the first principle. Three examples including the van der Pol damped nonlinear oscillator are presented to illustrate the excellent agreement with approximate solution using the exact frequency.     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

Friction and wear of Inconel 690 and Inconel 600 for steam generator tube in room temperature water

In the steam generators of nuclear power plants, the flow of cooling water can cause the tubes to vibrate, resulting in fretting wear damage due to contacts between these tubes and their supports. The tubes are made of Inconel 690 and Inconel 600 and the supports are made of STS 304. In this paper, fretting wear tests in water were performed using the materials Inconel 690 and Inconel 600 in contact with STS 304. Fretting tests using a cross-cylinder type set up were conducted under various vibrating amplitudes and applied normal loads in order to measure friction forces and wear volumes. Also, conventional sliding tests using a pin-on-disk type set up were carried out to compare these test results.In the fretting tests, friction force was found to be strongly dependent on normal load and vibrating amplitude. Coefficients of friction decreased with an increase in the normal load and a decrease in the vibrating amplitude applied. Also, the wear of Inconel 600 and Inconel 690 was predicted using a work rate model. Depending on the normal load and vibrating amplitude applied, distinctively different wear mechanisms and often drastically different wear rates occurred. It was found that the fretting wear coefficients for Inconel 600 and Inconel 690 were 9.3×10⁻¹⁵ and 16.2×10⁻¹⁵ Pa⁻¹, respectively. This study shows that Inconel 690 can result in lesser friction forces and exhibits less wear resistance than Inconel 600 in room temperature water.