机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

Ni,Cr, and Fe surfaces corroded by molten ZnCl2

Understanding the corrosion of molten ZnCl₂ on metal surfaces is significant for the corrosion protection of metals, sustainable use of molten salts, preparation of ZnO coatings, and so on. In this paper, surfaces of pure Ni, Cr, and Fe corroded by molten ZnCl₂ were investigated. The results show that Ni suffered very slight corrosion, while Cr experienced more serious corrosion than Ni, but lighter corrosion than Fe. The morphology of the corrosion of Cr and Fe, respectively, presented pitting and intergranular corrosion characteristics. Furthermore, nanostructured ZnO coatings were obtained on the surfaces of Ni and Fe, but not on the surface of Cr. The ZnO coating on the Ni surface was doped with a small amount of Zn₅(OH)₈Cl₂, and the ZnO coating on the Fe surface was doped with ZnFe₂O₄ and Zn₂OCl₂. The coatings on the Ni and Fe surfaces had an average thickness of 1.5 and 50 μm, respectively.     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

不同煤阶煤孔隙特征及其吸附能力响应

我国是煤炭资源大国，煤层气储量规模相当可观，但煤储层又具有低孔、低渗的不足，照搬国外或常规石油天然气的开采程序和方法已被证实是走不通的。应结合实际，根据不同地质条件、不同煤阶的开采程序，进行孔隙特征研究。煤孔隙特征、连通性和吸附能力对煤层气开采影响尤为重要，为研究煤孔隙结构特征随煤变质程度的变化关系及其吸附能力的响应特点，采取不同地区不同变质程度煤样，进行压汞测试和等温吸附实验。实验结果表明，煤孔隙度和平均孔径均随变质程度增加呈现降低—升高—降低的趋势；煤中孔隙连通性随煤变质程度增加逐渐变差；随煤变质程度增加，其最大吸附能力也呈现降低—升高—降低的总体趋势。     

基于儒可夫斯基变换的涡轮钻具叶片设计及性能分析

为提高涡轮钻具叶片使用性能和创新叶片设计理论,提出了基于儒可夫斯基保角变换法与经典水力翼型相结合的涡轮钻具叶片设计新方法,以?127涡轮钻具叶片为研究对象,运用搭建的涡轮钻具叶型参数化设计平台和自主设计的涡轮钻具性能测试台架,完成了5种翼型的造型设计,研究了5种叶片流场性能,开展了设计叶片的性能测试实验,对比分析了设计叶片与塔里木油田某型在役?127涡轮叶片的实际效能。实验及仿真结果表明,基于新方法设计的NACA-0012翼型加厚叶片在600 r/min转速及15 L/s流量的设计工况下,其单级扭矩达5.83 N·m,较相同条件下某在役?127涡轮的单级扭矩提高约6.4%,级效率提高约1.16%,整体性能有了实质提升。     

砖混再生粗骨料混凝土力学性能及工程应用研究

采用城市砖混结构拆除建筑垃圾加工制成的再生粗骨料,用不同配合比设计方法制备了砖混再生粗骨料混凝土,研究了砖混再生粗骨料对混凝土工作性、抗压强度、弹性模量、峰值应力、峰值应变以及应力应变关系的影响.结果 表明,相比较天然骨料和废弃混凝土制备的再生骨料,砖混再生骨料空隙率大,吸水率大,压碎指标高.使用附加用水量配合比方法制备的砖混再生粗骨料混凝土在力学性能上低于标准配合比方法制备的砖混再生粗骨料混凝土,但工作性能较好.随着砖混再生粗骨料取代率的增加,再生混凝土的力学性能呈现不同程度的降低.当取代率为100％时,使用标准配合比和附加用水量方法制备的再生混凝土28 d抗压强度分别降低了26.1％和11.9％,弹性模量分别降低了23.9％和22.9％,峰值应力分别降低了13.0％和21.9％,峰值应变分别增大了25.3％和14.9％.工程实践表明,采用砖混再生粗骨料配制的再生混凝土可以满足中低强度等级泵送混凝土的性能要求.     

Application of Mono‐ and Disaccharides in Drug Targeting and Efficacy

Carbohydrates and their conjugates play important roles in many biological processes including fertilization, differentiation, development, immune response, and infection. Their activities are largely dependent on the properties of terminal mono‐ or disaccharides. Galactose, mannose, fucose, glucose, sialic acid, etc., are commonly used as powerful scaffolds installed on drug molecules for targeting specific tissues including brain, liver, and cancers, and as epitopes for enhancing the targeting of various vaccines. This review focuses on the influence of their structural variations, including changes in sugar type, substituent groups and their positions, as well as length of linker portion, on the targeting of drugs or their efficacy. Particular attention is paid to the targeting properties of mono‐ and disaccharides applied in drug design and discovery.     

Enhanced piezoelectric strain of BiFeO3–Ba(Zr0.02Ti0.98)O3 lead-free ceramics near the phase boundary

The xBiFeO₃-(1-x)Ba(Zr_0.02Ti_0.98)O₃ + 1.0 mol% MnO₂ (xBF-BZT) lead-free piezoelectric ceramics were prepared by conventional solid-state reaction method. The structure, dielectric, and piezoelectric properties were studied. X-ray diffraction (XRD) analysis showed that xBF-BZT ceramics exhibited pure perovskite structure with the coexistence of tetragonal and rhombohedral phases (0.66 ≤ x ≤ 0.74). The Curie temperature T_c, the dielectric constant ε_r (1 kHz), dielectric loss tanδ (1 kHz), piezoelectric constant d₃₃, coercive field E_c (80 kV/cm), and remnant polarization P_r (80 kV/cm) of 0.7BF-0.3BZT-Mn ceramics were 491°C, 633, 0.044, 165 pC/N, 35.6 kV/cm, and 22.6 μC/cm², respectively. The unipolar strain of 0.7BF-0.3BZT reached up to 0.20% under the electric field of 60 kV/cm, which is larger than that (0.15%) of BiFeO₃–BaTiO₃ ceramics. These results indicated that the xBF-BZT ceramics were promising candidates for high-temperature piezoelectric materials.     

铝合金热轧板锭熔铸技术及设备

本文概述了近年来铝合金热轧板锭的熔铸设备和熔铸技术的发展和最新成就，重点介绍晶粒细化、熔体净化、检测及铸造新技术，为国内铝板带企业跟踪国际铝合金板锭熔铸技术、开展技术攻关和进行技术创新提供有益的参考。     

Synthesis and Characterization of Pr0.6-xNdxCa0.4FeO3-δ with Pechini Method

Pr0.6-x NdxCa0.4 FeO3-δ （ x = 0.0, 0.2, 0.3, 0.4, 0.5, 0.6） were synthesized using Pechini method. A number of studies were conducted concerning composition, specific area, crystalline structure and microstructure of the samples by means of FT-IR, BET, XRD TG-DTA and SEM. The results show that all the samples with different doping amounts of Pr^3＋ and Nd^3＋ on A-site are fine dispersed, and mean particle size less than 100 nm. The powders have good sinterability, and the relative density is 95% after sintered at 1200 ℃ for 2 h. It is found that all specimens are entirely single phase solid solutions with orthorhombic perovskite structure, the stable perovskitetype phase is formed completely after calcination at 900 ℃.