柴油机轴承盖螺栓断裂分析

柴油机发生多起轴承盖螺栓六角头与杆部过渡处断裂的故障,行驶里程为30000～70000 km.对故障件进行了断口分析、化学成分分析、力学性能检测、金相组织及硬度检验.结果表明,轴承盖螺栓属氢脆断裂.对库存件进行了氢含量检测,发现氢含量过高.提出了改进建议,取得了良好的效果.     

论高校开放式实验教学体系的构建

实施开放式实验教学已成为当前高校实验教学改革的突破口。实施开放式实验教学，必须构建科学的运行体系，主要包括教学目标体系、内容体系、保障体系和效能考评体系四个方面。     

中原油田水平井钻井液技术

根据中原油田地层高温、高盐、易塌、易漏失及水平井的特点,优选了适用于水平井的强抑制强封堵聚合物钻井液体系,并进行了现场应用.室内实验结果表明,优选的强抑制强封堵聚合物钻井液具有良好的井眼净化、摩阻控制、井壁稳定及油层保护等性能.现场应用时能满足钻井、录井、测井的需要,钻井施工顺利,取得了良好的经济和社会效益.     

沿江圩区排涝水文计算实例

设计排涝模数的计算是圩区排涝规划的主要内容之一,它的大小决定了排涝站的装机容量和涵闸尺寸.本文推求了安徽省马鞍山市大公圩地区的排涝模数,是沿江圩区排涝水文计算的一个应用实例.     

Determining stress intensity factors of composites using crack opening displacement

The main purpose of this paper is to find the mixed-mode stress intensity factors of composite materials using the crack opening displacement (COD). First, a series solution of the composite material with a crack was used to evaluate COD values. Then, the least-squares method was used to calculate mixed-mode stress intensity factors. This algorithm can be applied to any method that generates or measures COD values. The major advantage of this method is that COD values very near the crack tip are not necessary. Both finite element simulations and laboratory experiments were applied to validate this least-squares method with acceptable accuracy if the even terms of the series solution are removed.     

High-yield synthesis of single-crystalline 3C-SiC nanowires by a facile autoclave route

Single-crystalline 3C-SiC nanowires have been synthesized in large scale through a one-step autoclave route by the reaction of SiCl₄, (C₅H₅)₂Fe and metallic Na at 500 °C. Electron microscopy investigations show that the nanowires have typical diameters of 15-50 nm, lengths up to several tens of micrometers and grow along the [111] direction. The possible growth mechanism of the nanowires is discussed.     

N-Type Field-Effect Transistors Using Multiple Mg-Doped ZnO Nanorods

Nanorod field-effect transistors (FETs) that use multiple Mg-doped ZnO nanorods and a SiO₂ gate insulator were fabricated and characterized. The use of multiple nanorods provides higher on-currents without significant degradation in threshold voltage shift and subthreshold slopes. It has been observed that the on-currents of the multiple ZnO nanorod FETs increase approximately linearly with the number of nanorods, with on-currents of ~1 muA per nanorod and little change in off-current (~4times10^-12). The subthreshold slopes and on-off ratios typically improve as the number of nanorods within the device channel is increased, reflecting good uniformity of properties from nanorod to nanorod. It is expected that Mg dopants contribute to high n-type semiconductor characteristics during ZnO nanorod growth. For comparison, nonintentionally doped ZnO nanorod FETs are fabricated, and show low conductivity to compare with Mg-doped ZnO nanorods. In addition, temperature-dependent current-voltage characteristics of single ZnO nanorod FETs indicate that the activation energy of the drain current is very low (0.05-0.16 eV) at gate voltages both above and below threshold     

25mm厚钢板产生层间撕裂的原因和防治

层间撕裂并非是厚板独有的质量问题 ,结合工程实例 ,分析 2 5mm厚低合金钢板产生层间撕裂的原因。通过对钢材的超声波探伤检测、化学成分分析和Z向性能检测 ,指出层间撕裂主要与节点设计不当和钢材内非金属夹杂物偏析、分层有关 ,并提出了预防措施。对产生裂纹的构件视严重情况提出了不同的修补处理方法     

HPD-2型非临氢降凝催化剂工艺实验

利用HPD-2型非临氢降凝催化剂进行了中试实验。结果表明：HPD-2型非临氢降凝催化剂相对其他的同类催化剂产品液体收率较高，最高可达95％以上；在反应温度为380℃时，凝点降幅在50℃左右，降凝效果较好；产品性质稳定，具有很好的应用前景。     

钢锭零能少氧化均热轧制的研究

根据计算机的辅助分析,采用新的钢锭传搁、注后强制水冷却、垫铁脱模等工艺后,入炉钢锭的热焓已超过开坯轧制需要,利用普通均热炉代替钢锭保温车,可完全依靠到钢锭自身潜热与显热进行均热。对不同锭型与钢种采用经试验的最佳时间均热后再轧制,收与保温车均热钢锭直接轧制相同的效果。