Morphology,thermal, and mechanical properties of vinylester resin nanocomposites with various organo‐modified montmorillonites

New nanocomposites based on a vinylester resin (VER) and the organo‐montmorillonites (ODA‐M, BHL‐M, DEM‐M, BHLV‐M) modified with octadecylammonium, bis(2‐hydroxyethyl)lauryl ammonium, diethyl[2‐(methacryloyloxyl)ethyl]ammonium, and bis(2‐hydroxyethyl)lauryl(vinylbenzyl)‐ammonium chlorides, respectively, were prepared by dispersing the organoclays in VER, and subsequent crosslinking at finally 120°C. X‐ray diffraction studies and morphological studies using transmission electron microscopy revealed that exfoliation occurs for the VER/ODA‐M and BHL‐M composites, intercalation occurs for the VER/BHLV‐M composite, and neither intercalation nor exfoliation occur for the VER/DEM‐M and unmodified montmorillonite composites. On the whole, although the enhancement in flexural modulus was observed for the exfoliated ODA‐M and BHL‐M composites, the flexural strength was rather lowered. Dynamic viscoelastic measurement revealed that the ODA‐M, BHL‐M, and BHLV‐M nanocomposites have significantly higher storage modulus at the rubbery state than the other composites. Polym. Eng. Sci. 44:2041–2046, 2004. © 2004 Society of Plastics Engineers.     

Mechanical strengthening of Si cantilever by chemical KOH etching and its surface analysis by TEM and AFM

Mechanical strengthening of a Si cantilever by applying KOH wet etching was investigated. Two kinds of Si cantilever specimens having the different crystallographic orientations of the sidewall surfaces, i.e., Si{100} and Si{110}, were fabricated from the same SOI wafer by a Bosch process. The typical height and pitch of the scalloping formed on the sidewall were 248 and 917 nm, respectively. A 50 % KOH (40 °C) chemical wet etching was applied to increase the fracture stress of the Si cantilever. The fracture stress in the both of Si{100} and Si{110} cantilevers increased with the advance of the etching. The obtained maximum fracture stress in Si{100} and Si{110} were 4.2 and 3.7 GPa, respectively. Sidewall surface of the cantilever was analyzed to investigate the mechanical strengthening of Si cantilever by wet etching. The etched surface crystalline was analyzed by the transmission electron microscope (TEM), and confirmed that the thickness of the affected flow layer was less than 10 nm from the obtained TEM image. Then the change of the surface roughness by the KOH etching was analyzed by the atomic force microscope. The surface was smoothened with the advance of the KOH etching. The roughness value of Ra in Si{100} and Si{110} decreased to 12.1 and 37.7 nm, respectively.     

Specifying Real-Time Finite-State Systems in Linear Logic (Extended Abstract)

Abstract

Real-time finite-state systems may be specified in linear logic by means of linear implications between conjunctions of fixed finite length. In this setting, where time is treated as a dense linear ordering, safety properties may be expressed as certain provability problems. These provability problems are shown to be in pspace. They are solvable, with some guidance, by finite proof search in concurrent logic programming environments based on linear logic and acting as sort of model-checkers. One advantage of our approach is that either it provides unsafe runs or it actually establishes safety.     

Thermodynamic evaluation of the phase equilibria and glass-forming ability of the Fe–Si–B system

A thermodynamic study has been carried out on the Fe–Si–B ternary system, which is important in the development of transformer core materials and Ni-based filler metals. A regular solution approximation based on the sublattice model was adopted to describe the Gibbs energy for the individual phases in the binary and ternary systems. Thermodynamic parameters for each phase were evaluated by combining the experimental results from differential scanning calorimetry with literature data. The evaluated parameters enabled us to obtain reproducible calculations of the isothermal and vertical section diagrams. Furthermore, the glass-forming ability of this ternary alloy was evaluated by introducing thermodynamic quantities obtained from the phase diagram calculations into Davies–Uhlmann kinetic formulations. In this evaluation, the time–temperature-transformation (TTT) curves were obtained, which are a measure of the time required to transform to the minimum detectable mass of crystal as a function of temperature. The critical cooling rates calculated on the basis of the TTT curves enabled us to evaluate the glass-forming ability of this ternary alloy. The results show good agreement with the experimental data in the compositional amorphization range.     

Decoupling properties of singular LQ regulation problem

Some properties of a limiting solution derived from a standard LQ regulator problem are discussed in the case where the input weighting matrix tends to zero, for a discrete time system. The explicit limiting solution is given in some literature. It is shown that the limiting solution is closely connected with a disturbance decoupling problem. Moreover it is pointed out that the limiting feedback gain with the help of feedforward gain constructs the decoupled system with the maximum number of blocks.     

On a posteriori estimates of inverse operators for linear parabolic initial-boundary value problems

We present numerically verified a posteriori estimates of the norms of inverse operators for linear parabolic differential equations. In case that the corresponding elliptic operator is not coercive, existing methods for a priori estimates of the inverse operators are not accurate and, usually, exponentially increase in time variable. We propose a new technique for obtaining the estimates of the inverse operator by using the finite dimensional approximation and error estimates. It enables us to obtain very sharp bounds compared with a priori estimates. We will give some numerical examples which confirm the actual effectiveness of our method.     

Numerical simulation of pharyngeal bolus flow influenced by bolus viscosity and apparent slip

Pharyngeal bolus flow was simulated numerically using a finite element method. The bolus liquids were X-ray medium, glucose, and thickener solutions. For a low-viscosity bolus, the simulation showed a reasonable agreement of bolus velocity with X-ray measurements. The influence of bolus density on swallowing velocity was investigated numerically. Although a higher density resulted in a higher bolus velocity, the increase in velocity was modest. When the bolus viscosity was high, it was necessary to apply the slip boundary condition to obtain an agreement for bolus velocity between the simulation and X-ray measurements. The simulations also showed that the method of characteristic shear rate proposed by Zhu et al., Journal of Texture Studies, 2014, 45, 430–439 is effective for predicting the bolus velocity for shear-thinning fluids. In order to discuss the effect of saliva lubrication and the physical meaning of the characteristic shear rate, an immiscible two-layer flow of the core and wall layer was analyzed theoretically by analogy with mesopharyngeal bolus flow. The characteristic shear rate enabled us to correlate the macroscopic flow behavior and the viscosity of the core layer fluid. Lubrication due to the wall layer caused the apparent slip and enhanced the transfer of viscous core fluid. For viscous fluid that presented a large apparent slip in the two-layer model, the slip boundary condition was needed in the swallowing simulation. The numerical simulation and model flow analysis revealed the usefulness of characteristic shear rate and the importance of saliva-layer lubrication in swallowing.     

Computed tomographic evaluation of gas hole formation and structural quality in Gouda‐type cheese

Computed tomography (CT) was performed on Gouda‐type cheese during ripening to evaluate gas hole formation and structural quality. The cheese was exposed to different ripening conditions, including variations in ripening temperature and concentration of butyric acid bacteria. Computed tomography images were obtained every 2 weeks for 16 weeks to assess the volume, shape and location of gas holes. The results demonstrate that CT makes the nondestructive monitoring of cheese gas hole formation and evaluation of the structural features of cheese possible throughout the ripening period.     

Thermal and mechanical properties of bio-based polymer networks by thiol-ene photopolymerizations of gallic acid and pyrogallol derivatives

Allylated pyrogallol (A3PG) and acrylated pyrogallol (Ac3PG) as bio-based trienes, and allylated gallic acid (A4GA) and acrylated allyl gallate (Ac3A1GA) as bio-based tetraenes were synthesized from pyrogallol and gallic acid, respectively. Thiol-ene photopolymerizations of the bio-based polyenes and a pentaerythritol-based primary tetrathiol (pS4P) at the allyl/SH ratio of 1/1 produced photo-cured resins (A3PG-pS4P, Ac3PG-pS4P, A4GA-pS4P and Ac3A1GA-pS4P). The FT-IR spectral analysis revealed that thiol-ene reactions of thiol/allyl and thiol/acryloyl groups smoothly proceeded. Gel fractions of acryl-based cured resins were a little higher than those of allyl-based cured resins. The swelling test and dynamic mechanical analysis revealed that GA- and acryl-based cured resins exhibited higher crosslinking densities than PG- and allyl-based cured resins, respectively. A higher order of tan δ peak temperature was Ac3PG-pS4P (48.3 ° C) > Ac3A1GA-pS4P (24.1 ° C) > A4GA-pS4P (22.1 ° C) > A3PG-pS4P (?7.8 ° C). Ac3PG-pS4P displayed the highest 5 % weight loss temperature, tensile strength and tensile modulus among all of the cured resins.     

Droplet-based biochemical assay by magnetic wire manipulation between multiple droplets

Reaction performance of a droplet-based biochemical assay technique that uses magnetic wires as sample carriers is evaluated. Wires 2.0 mm in length, 0.05 mm in width, and 0.02 mm in thickness are fabricated by chemical etching, introduced into a droplet immersed in oil, and manipulated by the magnetic force of a moving magnet. Alkaline-phosphatase as an enzyme is immobilized on the wire surfaces by applying Au and self-assembled monolayer coatings, and the method’s on-chip reaction performance is evaluated. The enzymatic reaction is found to increase linearly as the number of wires and the reaction time increase. Relatively high performance reproducibility for enzymatic reactions is obtained; on average, the reaction absorbance, standard deviation, and coefficient of variance are found to be respectively 1.14, 0.103, and 9.1 %. The conductivity change in a fused droplet is used to evaluate the absolute volume of liquid transferred with the extracted wires and a value of 0.33 μl is obtained.