Assessment of the relative agronomic effectiveness of phosphate rocks under glasshouse conditions

Six phosphate rocks (PRs) of varying reactivities were compared with monocalcium phosphate (MCP) in a glasshouse experiment growing perennial ryegrass (Lolium perenne cv. Nui) as the test plant on four soils of contrasting P sorption capacity and exchangeable Ca. The cumulative dry matter yield over 10 harvests showed a significant response to P application in all soils. Based on relative yield and P uptake, MCP was the most effective P fertilizer followed by the reactive phosphate rocks, which were superior to the unreactive rocks in all soils. The relative agronomic effectiveness (RAE) and substitution ratio (SR) of individual PR fertilizers, calculated with respect to MCP using the methods of vertical and horizontal comparison, respectively, were similar over a range of fertilizer rate. There was a decline or slight increase in the performance of PRs with time in the low P sorption soils but a consistent increase in the high P sorption soils. Some initial influence of exchangeable Ca content of the soils on the relative performance of PRs was also observed. Generally the PRs performed better in high P sorption soils than low P sorption soils and in low exchangeable Ca soils than high exchangeable Ca soils.     

Development and evaluation of an improved soil test for phosphorus: 1. The influence of phosphorus fertilizer solubility and soil properties on the extractability of soil P

The objective of this work was to develop and evaluate a soil test suitable for estimating the phosphorus status of soils whether they were fertilized with soluble or sparingly soluble P fertilizers or both. Four New Zealand soils of contrasting P sorption capacity and exchangeable Ca content were incubated alone or with monocalcium phosphate (MCP), reactive North Carolina (NC) phosphate rock or unreactive Florida (FRD) rock, at 240 mg P kg^–1 soil, to allow the P sources of different solubilities to react with each soil and provide soil samples containing different amounts of extractable P, Ca and residual phosphate rock. The phosphorus in the incubated soils was fractionated into alkali soluble and acid soluble P fractions using a sequential extraction procedure to assess the extent of phosphate rock dissolution. Eight soil P tests [three moderately alkaline — Olsen (0.5M NaHCO₃) modified Olsen (pretreatment with 1M NaCl) and Colwell; three acid tests — Bray 1, modified Bray 1 and Truog; and two resin tests — bicarbonate anion exchange resin (AER) and combined AER plus sodium cation exchange resin (CER)] were assessed in their ability to extract P from the incubated soils.The 0.5M NaHCO₃ based alkaline tests could not differentiate between the Control and FRD treatments in any soil nor between the Control, NC and FRD treatments in the high P sorption soils. The acid extractants appeared to be affected by the P sorption capacity of the soil probably because of reabsorption of dissolved P in the acid medium. The AER test gave results similar to Olsen. Only the combined AER + CER test extracted P in amounts related to the solubility of the P sources incubated with each soil. Furthermore, when soil samples were spiked with FRD and NC and extracted immediately, the P extracted by the AER + CER test, over and above the control soils, increased with the amount and chemical reactivity of the rocks. There was no extraction of rock P by any of the alkaline extractions.Increases in the amounts of P extracted (P) by each soil test from the fertilized soils, over and above the control soils were compared with the amounts ofP dissolved from the fertilizers during incubation (measured by P fractionation). Soil P sorption capacity had least influence on the amounts of P extracted by the AER + CER and Colwell tests. However, the Colwell test was unable to differentiate between all P sources in all four soils and suffered from the disadvantage of producing coloured extracts. The AER + CER test appeared to have the potential to assess the available P status of soils better than the other tests used because of its ability to extract a representative portion of residual PR (in accordance with the amount and reactivity) and dissolved P, and thus to differentiate between fertilizer treatments in all four soils.     

Fatigue of viscoelastic polymers: 2. Fractography

The results of a fractographic study of fatigue failure in viscoelastic polymers is presented. Tests were conducted on a spherulitic low-density polyethylene in reversed loading using non-symmetrical deformation conditions. The microfractographic features have been found to depend on the deformation programme, the temperature of the test and the position on the fracture surface. The latter has been related to the different stages of growth revealed by plotting crack-growth propagation data. As well as interspherulitic fracture, other mechanisms that are sometimes prevalent involve cold-drawing, (fibrillation), and/or lamellar reorientation. The appearance of fatigue fracture surfaces of a non-spherulitic low-density polyethylene, a high-density polyethylene and a plasticized poly(vinyl chloride) corroborate the structural interpretations proposed to account for the observations with the spherulitic low-density polyethylene.     

Melting aspects of filled compounds in a modular co‐rotating twin screw extruder

In the polymer industry, precompounded materials are widely used. Carefully designed melting experiments were carried out to investigate melting mechanisms in master batched polymer compounds, using an intermeshing co‐rotating twin screw extruder. Calcium carbonate or aluminum powder was master batched with linear low‐density polyethylene (LLDPE). The calcium carbonates, which were used in the compounds, have differences in weight fraction and particle size. The compounds containing filler have higher thermal conductivities and viscosities than neat polyethylene. We observed melting initiation and propagation mechanisms of LLDPE compounds by removal and characterization of polymer compound carcasses in the melting region. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1990–2012, 2006     

Solvent fractionation of petroleum pitch for mesophase formation

Petroleum pitch (Ashland A240) has been subjected to thermal treatment and solvent fractionation to produce refined pitches to be evaluated as impregnants for C-C composites. The solvent fractions were obtained by sequential Soxhlet extraction with solvents such as hexane, benzene, and pyridine. Thermal treatment to 408 °C produced a mesophase pitch (≈50% mesophase); an appreciable portion of the mesophase was soluble in strong solvents. There were substantial differences in chemical composition and in pyrolysis behaviour of the fractions. As the depth of fraction increased, the pyrolysis yield and bloating increased, and the microstructure of the coke became finer until glassy microconstituents were formed in the deepest fractions.     

Dense subgraph maintenance under streaming edge weight updates for real-time story identification

Recent years have witnessed an unprecedented proliferation of social media. People around the globe author, everyday, millions of blog posts, social network status updates, etc. This rich stream of information can be used to identify, on an ongoing basis, emerging stories, and events that capture popular attention. Stories can be identified via groups of tightly coupled real-world entities, namely the people, locations, products, etc, that are involved in the story. The sheer scale and rapid evolution of the data involved necessitate highly efficient techniques for identifying important stories at every point of time. The main challenge in real-time story identification is the maintenance of dense subgraphs (corresponding to groups of tightly coupled entities) under streaming edge weight updates (resulting from a stream of user-generated content). This is the first work to study the efficient maintenance of dense subgraphs under such streaming edge weight updates. For a wide range of definitions of density, we derive theoretical results regarding the magnitude of change that a single edge weight update can cause. Based on these, we propose a novel algorithm, DynDens, which outperforms adaptations of existing techniques to this setting and yields meaningful, intuitive results. Our approach is validated by a thorough experimental evaluation on large-scale real and synthetic datasets.     

Using Electrical Capacitance Tomography to Investigate Gas Solid Contacting

An ECT system has been shown to be useful in observing differences in particle behaviour in a bubbling fluidised bed. An image analysis technique is further described that utilises the construction of solids concentration profiles at three key values, x = 0.2, x = 0.5 and x = 0.8, which have been identified as important solids concentrations in a new Bubble Structure Model. Significant differences in the bubble structure are shown to result when the concentration of fine particles is slightly increased in a bubbling fluidised bed. Changes of this type would seriously alter the gas solid contact efficiency in the fluidised bed, which would significantly influence selectivity of in‐bed catalytic reactions and gas residence time.     

Rheological and extrusion characteristics of glass fiber-reinforced polycarbonate

An experimental investigation of the rheological properties of glass fiber-reinforced polycarbonate melts and the extrusion of such compounds through capillary and slit dies is presented. The viscosity–shear rate function seems independent of instrument for cone-plate and capillary investigations. The presence of fibers increases the level of the viscosity. Normal stresses at fixed shear stress are also increased by the presence of fibers. The extrudate swell is decreased by the presence of fibers and surface roughness is increased. Fiber orientation increases and surface roughness decreases with increasing extrusion rate.     

Structure development in melt‐spinning syndiotactic polystyrene and comparison to atactic polystyrene

Syndiotactic polystyrene (s‐PS) and atactic polystyrene (a‐PS) were melt‐spun into filaments. The s‐PS filaments exhibited increasing amounts of crystallinity and orientation with increasing drawdown ratio and spinline stress. The a‐PS filaments were amorphous but exhibited birefringence. The birefringence and Hermans orientation factors for a‐PS were proportional to this spinline stress. In ice water and at low drawdown ratios, the s‐PS is glassy or mesomorphic. At higher drawdown ratios and spinline stresses, it crystallized. The crystalline form was the zigzag TTTT hexagonal α‐form. The birefringence and orientation factors of the s‐PS filaments were higher than those of the a‐PS filaments and the difference of the birefringence increased with increasing spinline stress. Mechanical testing results showed that the Young's modulus and tensile strength generally increased with increasing spinline drawdown ratio for both a‐PS and s‐PS filaments. The elongation to break was enhanced for both materials by increased chain orientation. Polym. Eng. Sci. 44:2141–2147, 2004. © 2004 Society of Plastics Engineers.     

Oxidative stability of soybean oils with altered fatty acid compositions

The oxidative stabilities of one canola oil and six soybean oils of various fatty acid compositions were compared in terms of peroxide values, conjugated dienoic acid values and sensory evaluations. Two of the soybean oils (Hardin and BSR 101) were from common commercial varieties. The other four soybean oils were from experimental lines developed in a mutation breeding program at Iowa State University that included A17 with 1.5% linolenate and 15.2% palmitate; A16 with 2% linolenate and 10.8% palmitate; A87-191039 with 2% linolenate and 29.6% oleate; and A6 with 27.5% stearate. Seed from the soybean genotypes was cold pressed. Crude canola oil was obtained without additives. All oils were refined, bleached and deodorized under laboratory conditions with no additives and stored at 60°C for 15 days. The A17, A16, A87-191039 and A6 oils were generally more stable to oxidation than the commercial soybean varieties and canola oil as evaluated by chemical and sensory tests. Canola oil was much less stable than Hardin and BSR 101 oils by both chemical and sensory tests. The peroxide values and flavor scores of oils were highly correlated with the initial amounts of linolenate (r=0.95, P=0.001). Flavor quality and flavor intensity had negative correlations with linolenate, (r=−0.89, P=0.007) and (r=−0.86, P=0.013), respectively.