Self-assembled monolayers of p-toluene and p-hydroxymethylbenzene moieties adsorbed on iron by the formation of covalent bonds between carbon and iron atoms for protection of iron from corrosion

An iron electrode was modified by electrolytic reduction in deaerated acetonitrile solution of p-toluenediazonium tetrafluoroborate CH₃C₆H₄N₂BF₄ (TDFB) or p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄ (HOTDFB) below 10 °C to form a self-assembled monolayer (SAM) of toluene CH₃C₆H₄- or hydroxymethylbenzene HOCH₂C₆H₄- (HOMB) moiety, probably adsorbed on the electrode by the formation of a covalent bond between carbon and iron atoms, as shown in references. The protective ability of the layer was examined by polarization measurement of the electrode in an aerated 0.5 M NaCl solution. The protective efficiencies of these two SAMs were not high, around 30%, a little higher than that of the toluenethiol CH₃C₆H₄SH SAM which was anchored on iron via a coordinate bond between sulfur and iron atoms. The iron surfaces modified with TDFB and HOTDFB were characterized by contact angle measurement, FTIR reflection spectroscopy and X-ray photoelectron spectroscopy. The persistence in protection of iron against corrosion by coverage with the HOMB SAM was confirmed by polarization measurements after immersion in 0.5 M NaCl for a long period of the time.     

超声波功率对铸锭内的气孔及组织细化的影响

研究了超声波功率对铝合金铸锭内气孔的影响,同时也考察了超声波功率对铝合金铸锭组织细化的影响,分析了超声波对铝合金铸锭内气孔影响的原因。研究结果表明,超声波在金属熔体内产生的空化效应可分为亚空化效应阶段和发展-发达阶段,只有在发展-发达阶段才具有良好的除气效果。     

Activity measurement of gallium in the B2 phase of the CoGa–Sb system by the EMF method with zirconia-based solid electrolyte

Gallium activity in the B2 phase regions of both binary Co–Ga and ternary Co–Ga–Sb systems was measured by EMF method with stabilized zirconia solid electrolyte The temperature range was 1073–1273 K and Sb concentrations were 1, 2 and 3 mol fractions. Ga activity at 1173 and 1273 K increases sharply in Ga rich region and the addition of Sb to the CoGa phase increases Ga activity. Activity change corresponds to the lattice parameter change with Sb addition to the CoGa phase.     

Cylindrical coils created with 3D X-ray lithography and metallization

The demand for microactuators is increasing recently. The key technology to realizing practical microactuators is microfabrication process. In the production of microminiature components, the technologies for processing high-aspect-ratio structures are essential. As one of these technologies, the LIGA process is widely known. Our laboratory researches the LIGA process to three-dimensional microfabrication and established the cylindrical-microcoil production process. In this paper, we have fabricated the cylindrical-microcoil for the solenoidal electromagnetic type microactuator. We designed and analyzed microactuators, and fabricated and evaluated microactuator coils produced by the combination of three-dimensional X-ray lithography and level copper plating. We succeeded in creating threaded groove-shaped structures with 10 μm line width, 20 μm pitch, and aspect ratio of 5 on the surface of an acrylic pipe by means of three-dimensional X-ray lithography. As a measure to suppress void generation, which is one of the shortcomings of electrolytic plating processes, the sputtering apparatus and plating equipment were improved, a pretreatment process was additionally provided, and the actual electrolytic plating method was improved. As a result, a void-free metallic deposit could be formed on a thin coil line. The processing technology enables the formation of thin-wire coil lines whose current paths feature a large allowable current-carrying capacity, enabling the production of miniature, high-output microactuators.     

Fabrication of large area diffraction grating using LIGA process

X-ray imaging is a very important technology in the fields of medical, biological, inspection, material science, etc. However, it is not enough to get the clear X-ray imaging with low absorbance. We have produced a diffraction gratings for obtaining high resolution X-ray phase imaging, such as X-ray Talbot interferometer. In this X-ray Talbot interferometer, diffraction gratings were required to have a fine, high accuracy, high aspect ratio structure. Then, we succeeded to fabricate a high aspect ratio diffraction grating with a pitch of 8 μm and small area using a deep X-ray lithography technique. We discuss that the diffraction gratings having a narrow pitch and an large effective area to obtain imaging size of practical use in medical application. If the pitch of diffraction gratings were narrow, it is expected high resolution imaging for X-ray Talbot interferometer. We succeeded and fabricated the diffraction grating with pitch of 5.3 μm, Au height of 28 μm and an effective area of 60 × 60 mm².     

Three-dimensional medical image recognition of cancer of the liver by a revised radial basis function (RBF) neural network algorithm

In this study, we propose a revised radial basis function (RBF) neural network algorithm and apply this algorithm to computer-aided diagnosis (CAD) of the liver. First, the revised RBF neural network algorithm is applied to recognition of the liver regions, and the recognition results are compared with those obtained using the conventional RBF neural network and the conventional multilayered neural network trained using the back-propagation algorithm. It is shown that the revised RBF neural network is accurate, and is a useful method because the parameters are automatically determined. Then, the revised RBF neural network is applied to CAD of the liver cancer called hepatocellular carcinoma (HCC).     

Multiphase composites of tetragonal zirconia agglomerate dispersed into alumina and alumina-zirconia matrices

Multiphase composites of yttria- and ceria-doped tetragonal zirconia agglomerates (10–50 m) dispersed into an alumina or alumina-zirconia matrix were sintered at 1500–1600 °C in air, followed by post-Hot Isostatic Pressing (HIP) at 1450°C and 150 MPa in an Ar gas atmosphere. The relative density of the recovered composites was above 98% of the theoretical density. By chemically etching on the surface of zirconia agglomerates, the sinterability of composites was apparently improved; and no microcracks nor pores were observed at the interface of agglomerate and matrix. According to scanning electron microscopy (SEM) observation, tetragonal and tetragonal-monoclinic zirconia agglomerates were highly dispersed into the alumina or alumina-zirconia matrix. The multiphase composites containing 10 vol% spherical agglomerates demonstrate the relatively low value of bending strength, < 400 MPa, and a high value of fracture toughness, > 11 MPa m^1/2. The crack propagation introduced by Vickers indentation was efficiently suppressed and deflected by the agglomerates.     

Two-step design of critical control systems using disturbance cancellation integral controllers

An efficient critical control system design is proposed in this paper. The key idea is to decompose the design problem into two simpler design steps by the technique used in the classical loop transfer recovery method (LTR). The disturbance cancellation integral controller is used as a basic controller. Since the standard loop transfer recovery method cannot be applied to the disturbance cancellation controller, the nonstandard version recently found is used for the decomposition. Exogenous inputs with constraints both on the amplitude and rate of change are considered. The majorant approach is taken to obtain the analytical sufficient matching conditions. A numerical design example is presented to illustrate the effectiveness of the proposed design.     

Design of discrete time adaptive PID control systems with parallel feedforward compensator

This paper deals with the design of an adaptive PID control system with a parallel feedforward compensator (PFC) for discrete-time SISO systems and its application to water level control of a 3-tank system. The proposed method utilizes the characteristics of almost strict positive realness (ASPR) of the controlled plant. A conventional design scheme of a PFC which realizes an ASPR augmented controlled plant is also proposed. Further it is shown that the introduction of an internal model improves the control performance of the control system with the PFC. The effectiveness of the proposed method is confirmed through water level control experiments on a three-tank SISO system.     

Fabrication of X-rays mask with carbon membrane for diffraction gratings

We have produced diffraction gratings for obtaining high resolution X-ray phase imaging, such as X-ray Talbot interferometer. These diffraction gratings were required to have a fine, high accuracy, high aspect ratio structure. Therefore, we decided to use the X-rays lithography technique that used synchrotron radiation of the directivity for a manufacture process. The accuracy of the completed structure depends largely on the accuracy of the X-ray mask. In our group, a resin material is conventionally used for the membrane of large X-ray masks. However, X-ray masks comprising a resin membrane have the disadvantage that, after several cycles of X-ray exposure, they crease and sag due to X-ray-derived heat. As a substitute for the conventional resin membrane, we experimentally fabricated a new X-ray mask using a carbon wafer membrane. The newly fabricated X-ray mask was subjected to X-ray exposure experiment. We succeeded in making the structure body which was almost shape. And the experimental results verified that the new mask did not deteriorate even when used repeatedly, demonstrating that it was highly durable.