Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Impact on the photothermal emission from single wall nanotubes by some alkali halide salts

We demonstrate that alkali-halide salts, particularly potassium bromide, can reduce the photothermal emission (PTE) from single walled carbon nanotubes (SWNT). PTE is a prominent spectral feature in Raman spectroscopy when a near infrared laser is used to analyze a dark colored sample. We subsequently show that trapping salts inside SWNT and coating SWNT with the salt has a more pronounced impact on not only reducing PTE, but also enhancing the intensity of the Raman spectral features. The effect, which we have called nanotube enhanced Raman spectroscopy (NERS), has differences and similarities to the widely studied surface enhanced Raman spectroscopy (SERS).     

Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

An MPEG‐4 Compliant Interactive Multimedia Streaming Platform Using Overlay Networks

This paper presents a multimedia streaming platform for efficiently transmitting MPEG‐4 content over IP networks. The platform includes an MPEG‐4 compliant streaming server and client, supporting object‐based representation of multimedia scenes, interactivity, and advanced encoding profiles defined by the ISO standard. For scalability purposes, we employ an application‐layer multicast scheme for media transmission using overlay networks. The overlay network, governed by the central entity of the network distribution manager, is dynamically deployed according to a set of pre‐defined criteria. The overlay network supports both broadcast delivery and video‐on‐demand content. The multimedia streaming platform is standards‐compliant and utilizes widespread multimedia protocols such as MPEG‐4, real‐time transport protocol, real‐time transport control protocol, and real‐time streaming protocol. The design of the overlay network was architected with the goal of transparency to both the streaming server and the client. As a result, many commercial implementations that use industry‐standard protocols can be plugged into the architecture relatively painlessly and can enjoy the benefits of the platform.     

On the Feasibility of Growing Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 Single Crystals

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by two methods: from solution using PbO as a self‐fluxing agent (SC method) and directly from the melt without fluxing (MC method). In both growth methods, an allomeric Pb[(Mg_1/3‐Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal was used as a seed. X‐ray diffraction patterns of ground crystals showed that phase‐pure perovskite PZNT91/9 single crystals were successfully fabricated by the above two methods. The composition of the crystals obtained by both the SC and MC methods was analyzed using X‐ray fluorescence, which confirmed that the crystal composition is close to the nominal value, although volatilization of PbO and segregation during crystal growth are inevitable. The MC PZNT91/9 crystals exhibit excellent piezoelectric properties, with the piezoelectric constant, d₃₃, in the range of 1800–2200 pC N^–1. This value is comparable to that of the SC crystals. However, the MC crystals show an abnormal dielectric behavior. In contrast with the SC crystals, in the MC crystals a much broader dielectric peak appears in the dielectric response curves, accompanied by a much lower peak temperature of around 105 °C. Furthermore, frequency dispersion is apparent over a much wider temperature range (even more apparent than in pure relaxors), where a large, i.e., about 70 °C, full width at half maximum (FWHM) for the dielectric peaks is observed in the dielectric response. It is speculated that such an unusual phenomenon correlates with defects, microinhomogeneities, and polar regions in the as‐grown MC crystals. The origins of this abnormality have not been interpreted in detail until now. However, optical observation of the domain structure confirms that both the SC and MC crystals possess complex structural states.     

Finite element analysis of advanced multilayer capacitors

We establish a systematic methodology to design and analyse electromagnetic components such as advanced multilayer ceramic capacitors (MLCCs) using the finite element (FE) method. We employ a coupled formulation to compute the interaction between the electric and magnetic fields. Unlike a linear distribution of current assumed in the circuit model, an accurate electrostatic solution to model the entire advanced MLCCs (4 × 4 × 27 = 432 cells) is presented. The FE solution is used to compute the lumped parameters for a range of frequencies. These lumped parameters are then used to compute the parasitic elements of the MLCCs. We introduce two algorithms to efficiently analyse the behaviour of a capacitor with changing frequency. The lower frequency (much below the self‐resonant frequency of the capacitor) algorithm separates the effect of the electric and magnetic fields and reduces the computational effort required to solve the FE problem, whereas, the high‐frequency algorithm couples the effect between the electric and the magnetic fields. We use these algorithms in conjunction with a new multiple scale technique to effectively determine the small values of R, L and C in MLCCs. The formulation, the implementation, and the numerical results demonstrate the efficacy of the present FE formulation and establish a systematic methodology to design and analyse advanced electromagnetic components. Copyright © 2003 John Wiley & Sons, Ltd.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Flammenpyrolytische Silikatbeschichtung bei Normaldruck als Alternative zu Vakuumverfahren. Combustion CVD of silica as an alternative method to vakuum treatment

In advancement of Pyrosil®‐technology a new kind of precursor delivery was developed, build and tested on real substrates. A Lab‐demonstrator was build to demonstrate the resources of the technology.