Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

切向结构永磁同步电机磁钢径向并联组合研究

针对低速大转矩切向结构永磁同步电机中磁钢尺寸对性能的影响进行研究.提出一种"工"字形排布的磁钢径向并联组合优化方案.在保证电机磁钢轴向长度和体积不变前提下,分析磁钢磁化方向长度变化对电机性能的影响.分析表明:磁钢的磁化方向长度在一定范围内增加可降低磁钢漏磁、增大反电动势和降低转矩波动;但磁钢的磁化方向长度过度增加会大大降低电机磁通面积,使得电机反电动势不增反降.在此基础上,提出一种降低磁钢漏磁、增大反电动势和降低转矩波动的三块磁钢径向并联组合的"工"字形排布方案:近气隙侧和近隔磁槽侧磁钢槽内分别插入磁化方向长度短、径向宽度窄的磁钢以降低近气隙侧和近隔磁套侧磁钢漏磁;近气隙侧磁钢和近隔磁槽侧磁钢之间采用磁化方向长度较短的磁钢以保证磁钢磁通面积降低得不多.通过仿真实验验证所提方案的可行性.     

Software assurance practices for mobile applications

Mobile software applications have to cope with a particular environment that involves small size, limited resources, high autonomy requirements, competitive business models and many other challenges. To provide development guidelines that respond to these needs, several practices have been introduced; however, it is not clear how these guidelines may contribute to solve the issues present in the mobile domain. Furthermore, the rapid evolution of the mobile ecosystem challenges many of the premises upon which the proposed practices were designed. In this paper, we present a survey of the literature on software assurance practices for mobile applications, with the objective of describing them and assessing their contribution and success. We identified, organized and reviewed a body of research that spans in three levels: software development processes, software product assurance practices, and software implementation practices. By carrying out this literature survey, we reviewed the different approaches that researchers on Software Engineering have provided to address the needs that raise in the mobile software development arena. Moreover, we review the evolution of these practices, identifying how the constant changes and modernization of the mobile execution environment has impacted the methods proposed in the literature. Finally, we introduced discussion on the application of these practices in a real productive setting, opening an area for further research that may determine if practitioners have followed the proposed assurance paradigms.     

Wear mechanism of a novel AlSiMgAl2O4Al2O3 composite used in the low vessel of an RH secondary refining furnace

A novel AlSiMgAl₂O₄Al₂O₃ composite brick was prepared and evaluated in the low vessel of an RH (the initials of Ruhrstahl and Hereaeus) secondary refining furnace; it was characterized by X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. The results show that after use, the AlSiMgAl₂O₄Al₂O₃ composite has a functional gradient with an erosion zone–reinforced zone–original zone phase distribution, in which the phases in the erosion zone (0–1.8?cm) are a Mg-hercynite spinel solid solution, α-Al₂O₃, and minor amount of Al₃Fe₅O₁₂. Furthermore, the phases in the reinforced zone (1.8–5.0?cm) are γ-AlON, 21RSiAlON, SiC, Mg_0.388Al_2.408O₄, and α-Al₂O₃; i.e., the Al and Si in the composite are completely converted into non-oxide reinforced phases. Finally, the phases in the original zone (>5.0?cm) show no change. The reaction mechanism is as follows. During operation, a Mg-hercynite spinel solid solution is formed in the erosion zone due to a reaction between MgAl₂O₄ and FeO from a refinery operation. Therefore, the slag erosion of the material is improved. The Al and Si metals undergo active oxidation, and 21RSiAlON flakes are subsequently formed from the products of the metastable Al₂O(g), SiO(g), and N₂(g) in the ambient. The γ-AlON is formed by a carbothermal reduction nitridation of the α-Al₂O₃ and residual active carbon from the resin binder. The 21RSiAlON and γ-AlON reinforce the composite brick and improve its high temperature performance accordingly. Its service life is 110% that of the magnesia-chrome bricks used in the same period. The reaction model was also established.     

Chest X-ray images super-resolution reconstruction via recursive neural network

Multimedia Tools and Applications - To address the problems of insufficient detail extraction and long training time in the super-resolution reconstruction of chest X-ray images, a method of chest...     

Intrinsic CFRP-metal-hybrids with rubber interface for the improvement of the damping behaviour

This paper presents an integrated passive damping approach in hybrid metal-CFRP parts for structural applications. In this concept a viscoelastic material is embedded in the joint zone of the hybrid component. To examine the connection strength single-lap-joint specimens were produced and tested and the influence of the used material combinations, different surface structures, and different process parameters i.e. the moment of cross-linking were evaluated. Afterwards, the metal-CFRP hybrids were tested in quasi-static tests to assess their connection strength and failure behaviour. Dynamic cyclic tensile tests with step-wise increased loading conditions were performed to determine the specimens damping behaviour and to estimate their fatigue performance. Finally, these results are compared to a state of the art metal-CFRP hybrid with rivets connecting both materials.     

多分量数据全波形反演在气藏检测中的关键问题——以苏里格气田为例

苏里格气田是中国典型的致密砂岩气藏，构造简单、平缓，横向非均质性强，有效储层与围岩声学特征差别小，地震响应不明显，常规地震监测方法预测难度大，但气田含气砂岩泊松比低，是地震气藏检测的有效参数。利用弹性全波形反演精度高和能处理复杂非均质介质的优势，反演地层拉梅常数、剪切模量和密度，并计算泊松比，从而进行气藏预测。重点阐述了苏里格气田多分量数据全波形反演初始模型建模、先验模型建模和地震数据预处理3个关键问题的处理方法。二维三分量数据反演和"甜点"预测结果表明：①对于具有强非均质性的苏里格气田，利用全波形反演获得精度较高的地层弹性参数能显著提高气藏预测的准确度；②苏里格地区构造简单、平缓，利用常规叠加速度并结合构造解释可以建立比较好的初始模型，从而有效地解决了周波跳跃和局部极小的难题；③先验知识的约束和地震数据的预处理是全波形反演成功应用于苏里格气田气藏检测的关键。     

Fabrication of dense nano-laminated tungsten carbide materials doped with Cr3C2/VC through two-step sintering

This work investigates the critical roles of two-step sintering (TSS) and laminated structure on the sintering behavior and mechanical properties of functionally graded WC-TiC-Al₂O₃ nanostructured composite materials doped with Cr₃C₂/VC. Results show that excellent mechanical properties are achieved for tailored TSS conditions with a hardness of 27.91?±?2.3?GPa and a flexural strength of 1423.3?±?23.5?MPa. The desirable mechanical properties are attributed to the suppressed grain growth without densification deterioration. TSS is more effective in facilitating the favorable dispersion of secondary phase toughening nano-particulates in a WC matrix than conventional sintering (CS). Cr₃C₂/VC dopant plays an important role in maximizing and shifting the temperature range of the kinetic window for WC-Al₂O₃ composites. Al₂O₃ crack deflection, transgranular Al₂O₃, microcracking, WC crack bridging and plate-like WC crack deflection are the major toughening mechanisms. Residual surface compressive stress induced by the graded structure is also an appreciated contribution to the improvement of mechanical properties.     

On stochastic comparisons of finite mixtures for some semiparametric families of distributions

In this paper, we consider the classical finite mixture model, which is an effective tool for modeling lifetime distributions for random samples from heterogeneous populations. We discuss new results on stochastic comparison for two finite mixtures when each of them is drawn from one of the following semiparametric families, i.e., proportional hazards, accelerated lifetime and proportional reversed hazards.