Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

水力旋冲钻井工具破岩影响因素模拟及应用

常规的冲击钻井工具不能满足井眼轨迹控制要求、使用寿命有限、缓解脱压不显著等问题,影响了在定向井钻井中的推广应用。建立ø215.9 mm PDC钻头和岩石的有限元模型,分析钻井参数对破岩效率的影响规律,结果表明:冲击频率为17.5 Hz和35 Hz时,破岩效率最优; 破岩效率随钻压增大而增加,而后变化逐渐平缓; 破岩效率随钻头转速增大而增加; 破岩效率随冲击载荷的增加变化平缓。据此研制了新型水力旋冲钻井工具。现场试验表明,该工具符合定向水平井“一趟钻”工艺要求,使机械钻速提高56%,使用寿命达150 h,MWD信号正常。     

100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

聚硅氧烷改性PBT的制备及其结构与性能研究

为了提高聚对苯二甲酸丁二醇酯(PBT)分子链段的柔顺性,选用聚硅氧烷(PDMS)对其改性。将PDMS母粒(PBT-b-PDMS)与PBT按一定质量配比进行熔融共混制得不同PDMS母粒含量的PBT-b-PDMS/PBT共混切片(简称共混切片),对共混切片的结构与性能进行了研究。结果表明:PDMS母粒中软链段PDMS质量分数约为50%,硬链段PBT质量分数约为50%;PDMS以微米级微球均匀分布于PBT连续相中形成海岛结构;PDMS母粒与PBT在共混改性过程中,不存在较强的分子作用力,两者为宏观上的相容, PDMS质量分数大于等于16%后相容性逐渐变差;随着PDMS的增加,共混切片的玻璃化转变温度逐渐降低,表面接触角先逐渐减小后增大;当PDMS添加质量分数小于16%时,共混切片的亲水性能较好。     

外部气体辅助注塑制品翘曲变形数值模拟

基于聚合物黏弹性理论与外部气体辅助注塑（EGAIM）的特点，构建了EGAIM气体保压阶段及脱模后自然冷却阶段制品内应力?应变的力学模型。在此基础上，采用耦合有限元法（FEM）对EGAIM平板制件的翘曲变形进行模拟计算，模拟结果与实验结果基本一致，验证了所建计算模型有效可靠。     

Potential Anti-Cancer Activities and Mechanisms of Costunolide and Dehydrocostuslactone

Costunolide (CE) and dehydrocostuslactone (DE) are derived from many species of medicinal plants, such as Saussurea lappa Decne and Laurus nobilis L. They have been reported for their wide spectrum of biological effects, including anti-inflammatory, anticancer, antiviral, antimicrobial, antifungal, antioxidant, antidiabetic, antiulcer, and anthelmintic activities. In recent years, they have caused extensive interest in researchers due to their potential anti-cancer activities for various types of cancer, and their anti-cancer mechanisms, including causing cell cycle arrest, inducing apoptosis and differentiation, promoting the aggregation of microtubule protein, inhibiting the activity of telomerase, inhibiting metastasis and invasion, reversing multidrug resistance, restraining angiogenesis has been studied. This review will summarize anti-cancer activities and associated molecular mechanisms of these two compounds for the purpose of promoting their research and application.