Optimization of reinforcement layout of scissor‐type bridge using differential evolution algorithm

Scissors mechanisms are commonly used in safety engineering during the construction of temporary structures, owing to their inherent advantages of foldability, transformability, and reusability. We effectively utilized these scissors mechanism features to develop a lightweight, deployable emergency Mobile Bridge (MB) based on optimization, and control of the folding structure. Here, we discuss the problems of optimal reinforcement layout for the MB by formulating and solving three optimization problems, namely: (a) the load capacity maximization problem, (b) the weight minimization problem, and (c) coupling the load capacity maximization problem and the weight minimization problem. The potential benefits resulting from the application of reinforcement were evaluated using a combination of finite element analysis and an optimization algorithm based on the differential evolution method. The results demonstrate the significant positive influence of the additional reinforcing members. In particular, the limit load was increased by over 10 times, while the weight was decreased to approximately half. The proposed methodology enabled the development of a substantially improved version of the MB characterized by a higher load capacity and lower weight in comparison to the initial bridge design.     

Reduction of Vibration in Concentrated Winding Permanent Magnet Synchronous Motor by Means of Skew Effects of Rotor

Global warming and the problem of successfully incorporating environmental safeguards are promoting the need for a more power‐efficient motor. Therefore, as a driving source, permanent magnet synchronous motors (PMSMs) with concentrated winding are widely used in a variety of fields. However, a PMSM with a concentrated winding generates more vibration than one with a distributed winding because of the radial electromagnetic force. This paper describes the effect of a new skewed rotor on the characteristics of a concentrated winding PMSM. We investigated this effect by three‐dimensional finite element method (3D FEM) analysis and measurement. We also demonstrate that the proposed rotor is effective in reducing the radial electromagnetic force without decreasing motor efficiency. © 2014 Wiley Periodicals, Inc. Electr Eng Jpn, 187(2): 33–43, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22400     

Enhanced catalytic activity of nanoshell carbon co-doped with boron and nitrogen in the oxygen reduction reaction

The use of carbon cathode catalysts in polymer electrolyte fuel cells instead of the current platinum catalysts is attracting increasing attention. We claim that two factors are important for enhancing the activity of carbon cathode catalysts in the oxygen reduction reaction (ORR): the formation of a nanoshell structure and co-doping with boron and nitrogen. Herein, we investigate the preparation and characterization of active ORR carbon catalysts that combine the above factors. Boron and nitrogen (BN)-doped nanoshell-containing carbon (BN-NSCC) was prepared by carbonizing a mixture of poly(furfuryl alcohol), cobalt phthalocyanine, melamine, and a trifluoroborane–methanol complex at 1000 °C. Transmission electron microscopy and X-ray photoelectron spectroscopy revealed the formation of nanoshell structures with distorted graphitic layers and the introduction of boron and nitrogen atoms, respectively. The ORR activity was evaluated in oxygen-saturated 0.5 mol dm^?3 H₂SO₄ using Koutecky–Levich analysis. The BN-NSCC showed an eight to ten times higher ORR activity than undoped NSCC, with an increased number of electrons participating in the reaction. Tafel analysis revealed a change in the rate-determining step caused by BN-doping. Thus, the combination of a nanoshell structure and co-doping with boron and nitrogen was found to improve the ORR activity of carbon catalysts.     

Fabrication of octacalcium phosphate block through a dissolution-precipitation reaction using a calcium sulphate hemihydrate block as a precursor

Although octacalcium phosphate (OCP) powder and a collagen/gelatin composite demonstrate good potential as bone substitutes, an OCP block has not been fabricated to date. In this study, the feasibility of fabricating an OCP block was evaluated through a dissolution-precipitation reaction using a calcium sulfate hemihydrate (CSH) block as a precursor. When the block was immersed in a phosphate salt solution, its composition changed to that of OCP, while its structure was maintained. The diametral tensile strength (DTS) of the OCP block was 1.0?±?0.2?MPa. The macroporosity and microporosity of the OCP block were 33.4?±?4.5% and, 69.0?±?1.6%, respectively. New bone attached well to the OCP block, and this block was partially replaced by bone 2 weeks after implantation. Four weeks after implantation, the surface of the OCP block was nearly covered with new bone and ~30% of the block was replaced by new bone, while no replacement by bone was observed in the case of a hydroxyapatite (HAp) block used as a control. It is concluded that OCP blocks are potentially suitable for their use as artificial bone substitutes.     

Modeling of quantitative relationships between physicochemical properties of active pharmaceutical ingredients and tensile strength of tablets using a boosted tree

Objectives: The aim of this study was to explore the potential of boosted tree (BT) to develop a correlation model between active pharmaceutical ingredient (API) characteristics and a tensile strength (TS) of tablets as critical quality attributes.

Methods: First, we evaluated 81 kinds of API characteristics, such as particle size distribution, bulk density, tapped density, Hausner ratio, moisture content, elastic recovery, molecular weight, and partition coefficient. Next, we prepared tablets containing 50% API, 49% microcrystalline cellulose, and 1% magnesium stearate using direct compression at 6, 8, and 10?kN, and measured TS. Then, we applied BT to our dataset to develop a correlation model. Finally, the constructed BT model was validated using k-fold cross-validation.

Results: Results showed that the BT model achieved high-performance statistics, whereas multiple regression analysis resulted in poor estimations. Sensitivity analysis of the BT model revealed that diameter of powder particles at the 10th percentile of the cumulative percentage size distribution was the most crucial factor for TS. In addition, the influences of moisture content, partition coefficients, and modal diameter were appreciably meaningful factors.

Conclusions: This study demonstrates that BT model could provide comprehensive understanding of the latent structure underlying APIs and TS of tablets.     

Colored amorphous silica-based powder with TiN nanocrystals precipitated by ammonolysis of Ti–Si–O ternary glass

Coloration of amorphous silica powder containing titania was investigated by nitridation in an ammonia flow. The oxide precursors were obtained by the hydrolysis of a mixture of tetraethyl orthosilicate (TEOS) and tetrabutoxy titanium (TBT). The color changed with the amount of TBT in the mixture, the hydrolysis pH and the ammonolysis temperature. The original white color of the 8 mol% TBT powder hydrolyzed under basic pH conditions changed to pale goldenrod at 700°C, then to dark olive green at 800°C, and further darkened with increasing ammonolysis temperature. A steel-blue color appeared at 900°C for the powder obtained with 3 mol% TBT, and increased in darkness at 1000°C. A similar bluish color was observed for powders obtained by acidic hydrolysis after ammonolysis above 900°C, and this was independent of the amount of titania, although the chroma decreased with increasing firing temperature for the powder with 3 mol% TBT. The ammonolysis powder products were characterized using X-ray diffraction (XRD), electron probe micro analysis (EPMA), transmission electron microscopy-electron energy-loss spectroscopy (TEM-EELS), scanning transmission electron microscopy-high-angle annular dark-field imaging (STEM-HAADF) and Ti–K edge X-ray absorption fine structure (XAFS). The color change was related to both precipitated TiN nanocrystals and residual titanium in the amorphous silica matrix. The TiN exhibited a goldish reflection and also plasmonic absorption from light blue to gray depending on the TiN crystallite size. The plasmonic absorption and resonance of nanocrystalline TiN will be useful similarly to that of gold in nanotechnology for various kinds of energy application.     

Multifunctional Composites of Chiral Valine Derivative Schiff Base Cu(II) Complexes and TiO2

We have prepared four new Cu(II) complexes containing valine moieties with imidazole ligands at the fourth coordination sites and examined their photo-induced reactions with TiO₂ in order of understanding the reaction mechanisms. Under a nitrogen atmosphere, the intermolecular electron transfer reactions (essentially supramolecular interactions) of these systems, which resulted in the reduction of Cu(II) species to Cu(I) ones, occurred after UV light irradiation. In this study, we have investigated the conditions of the redox reactions in view of substituent effects of aldehyde moieties. The results of cyclic voltammetry (CV) on an rotating ring-disk electrode (RRDE) suggested that the substitution effects and redox potentials were correlated. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were also performed to simulate the UV–Vis and circular dichroism (CD) spectra; the results revealed a reasonably good correlation between the substituent effects and the highest occupied molecular orbitals and the lowest unoccupied molecular orbitals (HOMO-LUMO) gaps associated with the most intense transition bands. In addition, we summarized the substitution effects of Cu(II) complexes for their corresponding UV light-induced reactions.