Visible light-activated degradation of microcystin-LR by ultrathin g-C3N4 nanosheets-based heterojunction photocatalyst

Microcystins (MCs) is a harmful toxin generated by blue-green algae in water, which has seriously threatened the ecological safety of water and human body. It is urgent to develop new catalysts and techniques for the degradation of MCs. A feasible electrostatic self-assembly method was carried out to synthesize BiVO₄/g-C₃N₄ heterojunction photocatalyst with highly efficient photocatalytic ability, where BiVO₄ nanoplates with exposed {010} facets anchored to the g-C₃N₄ ultrathin nanosheets. The morphology and microstructure of the heterojunction photocatalysts were identified by XRD, SEM, TEM, XPS, and BET. The g-C₃N₄ nanosheets have huge surface area over 200 m²/g and abundant mesoporous ranging from 2-20 nm, which provides tremendous contact area for BiVO₄ nanoplates. Meanwhile, the introduction of BiVO₄ led to red-shift of the absorption spectrum of photocatalyst, which was characterized by UV-vis diffuse reflection spectroscopy (DRS). Compared with pure BiVO₄ and g-C₃N₄, the BiVO₄/g-C₃N₄ heterojunction shows a drastically enhanced photocatalytic activity in degradation of microcystin-LR (MC-LR) in water. The MC-LR could be removed within 15 minutes under the optimal ratio of BiVO₄/g-C₃N₄. The outstanding performance of the photocatalyst is attributed to synergetic effect of interface Z-scheme heterojunction and high active facets {010} of BiVO₄ nanoplates, which provides an efficient transfer pathway to separate photoinduced carriers meanwhile endows the photocatalysts with strong redox ability.     

胶片导切机旋转刀的有限元分析

基于有限元分析方法,对密炼机上辅机系统的胶片导切机旋转刀刀片强度进行分析,并根据分析结果优化旋转刀刀片的结构设计和材料选择。结果表明:传统机械破碎强度(P_b)理论不适用于胶片导切机旋转刀的胶片切割;在剪切力(F_2)一定的条件下,减小胶片导切机旋转刀刀片安装偏角或者增大刀刃宽度(W)可以降低旋转刀刀片的应力,从而减少刀片崩裂,延长刀片的使用寿命,也可以通过更换材料和改变热处理的方法来降低刀片制造成本;在F_2和P_b一定的条件下,适当增大W可以减小胶片导切机投产后的磨刀频率,降低维护成本。     

YSZ/MoS2 self-lubricating coating fabricated by thermal spraying and hydrothermal reaction

Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS₂ composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS₂ powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS₂ powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS₂ flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10^?7 mm³ N^?1 m^?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS₂ transfer films and the ultra-smooth of the worn surfaces of hybrid coatings.     

Corrosion resistance of Al–Cr-slag containing chromium–corundum refractories to slags with different basicity

Al–Cr slag is the solid waste generated by the smelting of Cr metal. It presents a range of environmental hazards. This study addressed the corrosion resistance of Al–Cr slag containing chromium–corundum refractories to slags with different basicity. Herein, we provide suggestions for the use of Cr–corundum of different basicity in kilns. Al–Cr slag, brown fused Al₂O₃, and chrome green were used as the raw materials, with pure calcium aluminate cement being used as a binder. The brick samples, prepared using different blends of chrome green and corundum, were fired at 1600?°C, and subsequently subjected to a slag corrosion test. After corrosion by slag of different basicity, the phase composition and microstructure of the sample were analyzed by X-ray diffraction, energy dispersive spectrometer and scanning electron microscopy. There were two major findings. First, Cr–corundum brick made from Al–Cr slag has a better slag corrosion resistance than that made from Cr₂O₃ and brown fused Al₂O₃. Second, Cr–corundum brick made from Al–Cr slag has superior corrosion resistance to slag with a CaO:SiO₂ ratio of 2:1.     

Computational Fluid Dynamics Study on a Top-Blown Smelting Process with Lance Failure in an Isa Furnace

JOM - The Isa/Ausmelt smelting technology with a top submerged lance (TSL) has been extensively used in copper smelting processes. However, the TSL is extremely vulnerable to damage and failure...     

In-situ crystal growth and photoluminescence properties of YBO3: Tb3+ microstructures

Three-dimensional (3D) YBO₃:Tb³⁺ flower-like and dense flower-like hierarchitecture constituted of nanoflakes are solvothermally synthesized in the presence of polyborate precursors in the mixture of ethanol and water. The growth process of the YBO₃:Tb³⁺ flowers and dense flowers was explored based on the time-dependent experiment and the results showed that the growth mechanism follows an in situ growth rather than self-assembly process as reported previously. YBO₃:Tb³⁺ morphologies composed of nanoflakes are achieved by controlling the concentration of ethanol and dependence of photoluminescence on morphology was studied. Remarkable photoluminescence enhancement was observed for YBO₃:Tb³⁺ with flower-like morphology demonstrating the potential of the microstructure in future applications as a green phosphor. Such a synthetic method and growth mechanism may be applied to fabricate complex 3D architectures of other materials.