Off-line multiresponse optimization of electrochemical surface grinding by a multi-objective programming method

The objective of this study is to optimize electrochemical grinding (ECG) process responses simultaneously by an off-line multiresponse optimization methodology. The responses considered as objectives are side and bottom overcuts, surface finish, spindle load, total metal removal rate, and wheel wear. Materials of 304 Stainless Steel are ground by the ECG process. The process variables optimized for the above objectives include electrolyte type, wheel material, grit size, grit concentration, d.c. voltage, electrolyte flow rate, wheel speed, feed rate, and ripple effect. A simple weighting method transforms the multi-objective problem into a single-objective programming format and then, by parametric variation of the weights, the set of non-dominated optimum solutions are obtained. It is shown in this paper that the multi-objective optimization methodology can be applied for an ECG operation, and that the optimal operating conditions for any given set of weights can be obtained depending upon the objectives.     

伊犁盆地生成发展概述

本文对伊犁盆地的生成和发展做了初步探讨,认为它是在前震旦纪结晶基底之上经历了较长时间的抬升之后形成和发展起来的双层结构盆地,即石炭纪体内裂谷盆地,石炭纪后山间陆相盆地。     

改进型的动态矩阵控制

本文在分析了七十年代出现的动态矩阵控制算法的基础上,发现该算法在克服干扰的定值调节方面质量不高,从而提出了变预估修正系数的改进算法。并且通过理论分析和实际应用证实了这种改进的正确性和优越性。在过程控制实验室的温度装置上进行的实时控制试验,表明了这种改进算法有较大的实用价值。     

High-temperature hydrothermal systems in West Yunnan Province, China

There are more than 660 thermal springs in West Yunnan Province, 30 of which are high-temperature hydrothermal systems with reservoir temperatures above 150°C.All thermal springs in West Yunnan are under the control of the tectonics, most of them being distributed at anticlinoria of metamorphic rocks and granites. This paper discusses the relationship between thermal areas and tectonics, the correlation between thermal springs in West Yunnan and North Thailand, and the geothermal prospects in West Yunnan.     

Simulation of programmable logic controller

The development and test of a PLC control program takes time, increases equipment down-time, and might damage hardware due to program errors. All of these problems can be eliminated if there is a computer simulation system for testing control programs off line. This paper presented a new method, called Direct Sequential Method, for simulating PLCs. This method resolves a ladder logic sequentially by applying a series of logic deductions. This simulation system has been implemented in C and tested successfully.     

Surgical navigation by autostereoscopic image overlay of integral videography

This paper describes an autostereoscopic image overlay technique that is integrated into a surgical navigation system to superimpose a real three-dimensional (3-D) image onto the patient via a half-silvered mirror. The images are created by employing a modified version of integral videography (IV), which is an animated extension of integral photography. IV records and reproduces 3-D images using a microconvex lens array and flat display; it can display geometrically accurate 3-D autostereoscopic images and reproduce motion parallax without the need for special devices. The use of semitransparent display devices makes it appear that the 3-D image is inside the patient's body. This is the first report of applying an autostereoscopic display with an image overlay system in surgical navigation. Experiments demonstrated that the fast IV rendering technique and patient-image registration method produce an average registration accuracy of 1.13 mm. Experiments using a target in phantom agar showed that the system can guide a needle toward a target with an average error of 2.6 mm. Improvement in the quality of the IV display will make this system practical and its use will increase surgical accuracy and reduce invasiveness.     

光纤Bragg光栅监测钢筋混凝土结构应变的实验研究

研究了光纤Bragg光栅在钢筋混凝土结构应变监测中的应用。对其应变、温度灵敏系数进行标定,将其埋设在钢筋混凝土梁内,实现对结构内部应变的监测,并对其工作状态做出评价。实验结果与理论值、传统监测手段监测结果一致。研制出一种钢管封装Bragg光栅温度传感器监测温度,对光纤Bragg光栅的应变与温度的同时测量进行了研究。     

Development of an end-point detector for parylene deposition process

Parylene is an emerging material for MEMS. It is an organic material that is grown by using the chemical vapor deposition method at room temperature. The deposition thickness is commonly controlled by the amount of solid-phase dimer loaded in a sublimation chamber. In a conventional deposition machine, the end point of the process is designated by the moment the dimer is exhausted. However, this end-of-process criterion does not offer precise, repeatable control of film thickness. We present the results of the development of an in situ end-point detector for a Parylene chemical vapor deposition process. The detector is based on the thermal transfer principle and can be implemented on commercial parylene deposition systems with minimal system modification. Such a sensor enables a user to stop the deposition when a targeted thickness is reached. The end point detector is very simple to implement on existing parylene deposition systems. A series of such sensors with different target deposition thickness would allow extraction of the actual deposition rate within a deposition run.     

A Study of the Compatibility Between Asphalt and SBS

In this article, the compatibilities between different components of a base asphalt and styrene butadiene styrene (SBS) have been analyzed from microscopic structures. Specifically, the asphalt was separated into three components: saturates, aromatics, and resins, by Solvent Recycled Absorption Chromatography Separation Technology (SRACST). The compatibilities between these different components and the polymer were compared with the help of Fluorescence Microscope (FM) with which the existing state of the polymer SBS in these different components could be examined obviously. The modified effects indicated that aromatics could cause SBS swollen and, resins dissolved SBS better than saturates, though both the two components could partially dissolve SBS and the two mixtures presented two immiscible phase systems. In order to further investigate the compatibility between aromatics and SBS, from macroscopic properties, an additive rich in aromatics was added to the SBS/asphalt mixture, and the result was satisfactory.     

Chosen plaintext attack on a cryptosystem with discretized skew tent map

An encryption system with discretized skew tent map has been proposed recently by N. Masuda . However, there is a fundamental weakness with this chaotic cryptographic scheme. In this paper, a chosen plaintext attack requiring only two plaintexts is proposed. An improved version of this attack that narrows the key space need to be searched is also suggested. The test results demonstrate that this encryption cryptosystem is easily broken under the proposed chosen plaintext attack.