A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Formation of a protective layer against corrosion on Mg alloy via alkali pretreatment followed by vanillic acid treatment

Although Mg alloy possesses high specific strength, low density, and good biocompatibility, poor corrosion resistance hinders its further applications. In the present study, an innovative protective layer against corrosion was prepared on the AZ31 Mg alloy via alkali pretreatment followed by vanillic acid treatment. The alkali pretreatment supplied –OH for the AZ31 Mg alloy surface to react with vanillic acid. The vanillic acid treatment played a crucial role in enhancing the corrosion resistance due to the excellent ability to act as a barrier and retard aqueous solution penetration, which effectively isolated the underlying Mg alloy from the corrosive environment. The corrosion current density of alkali and vanillic acid-treated Mg alloy (AZ31V) almost showed two orders of magnitude lower values in comparison with that of the AZ31 Mg alloy, and the corrosion potential of AZ31V Mg alloy increased from −1.41 to −1.25 V. The immersion tests proved that there was no occurrence of severe corrosion. Hence, the alkali pretreatment and vanillic acid treatment may represent a promising method to improve the corrosion resistance of Mg alloy.     

高盐高有机制药废水污泥电渗透高干脱水

为研究高盐高有机制药废水污泥的电渗透脱水效果，深入认识化学污泥的电脱水过程，本文采用电渗透高干脱水技术对经抽滤脱水的高盐高有机制药废水化学污泥进行深度脱水，考察了泥饼初始pH的改变对污泥电渗透高干脱水过程中阴阳极污泥的含水率、电流、电导率、pH、zeta电位与能耗的影响，验证了对高盐高有机制药废水污泥实行电渗透高干脱水的可行性，解析了化学污泥电渗透脱水过程的机制。结果表明，泥饼pH为2、3、4时，zeta电位为正值，电渗流反向流动，无法脱水；pH增至5时，zeta电位为负值，电渗流从阴极脱除，污泥含水率从53.2%降至44.8%，脱水效果最好；但pH增至6时，脱水量有所降低。污泥电导率随pH的增加而降低。pH为5时初始电流最大。脱水15min时，即污泥含水率降至45.5%时，能源利用率最高。     

链轨节用钢15B36Cr的开发与试制

淮钢采用90 t顶底复吹转炉-LF-RH-200 mm×200 mm连铸-连轧工艺流程试生产了2炉Φ60 mm链轨节用钢15B36Cr(/%:0.30～0.37C、0.15～0.30Si、1.20～1.50Mn、≤0.040P、≤0.0505、0.20～0.40Cr、≤0.25Ni、≤0.35Cu、≤0.06Mo、0.0005～0. 0030B)。通过加严影响淬透性化学成分,控制出钢碳≥0.08%,转炉有效挡渣和下渣检测系统控制下渣,LF炉铝粒和电石渣面脱氧,RH最低真空度处理20～30 min,结晶器电磁搅拌、末端电磁搅拌和连铸低过热度保护浇铸等工艺措施,15B36Cr钢的化学成分稳定控制在内控范围内,除了B粗以外,其他类型非金属夹杂物级别全部控制在1.0以内,淬透性控制在较窄的范围内,试制钢种关键技术指标达到客户和预期设计要求。     

氧气底吹熔炼氧枪浅析

系统地论述了氧气底吹熔炼氧枪的结构、工作原理、设计计算方法、材质及蚀损机理．指出了延长氧枪使用寿命的措施。     

电路电磁兼容建模与仿真

提出了对暴露在任意外场中的传输线进行时频分析的新方法，这种方法非常稳定，它能够与任意的传输线模型和电路仿真方法兼容，并且使用这种方法得到的仿真值和实际值之间的差别小于1％。     

基于DTW改进算法的孤立词识别系统的仿真与分析

传统的DTW算法在进行孤立词语音识别时着重于时间规整和语音测度的计算，而没有对数据的可靠性和有效性进行分析。本文提出了一种改进的端点检测算法，并采用一种改进的DTW算法，在计算机上进行了仿真。实验结果表明采用改进后的DTW算法有效的降低了识别时间和存储数据量，提高了系统性能。