Numerical simulation and experimental validation of a multi-step deep drawing process

This paper presents the numerical simulation of an industrial multi-step deep drawing process. A large strain finite element formulation including a hyperelastic elastoplastic constitutive model and a contact-friction law is used to this end where the steel sheet material parameters considered in the analysis are previously derived through a characterization procedure of its mechanical response. The numerical predictions of the final shape and thickness distribution of the blank are compared and discussed with available experimental values measured at the end of three successive drawing steps. In addition, a plastic work-based damage index is used to assess failure occurrence during the process. The damage values computed at the end of the drawing process are found to be lower than that corresponding to rupture in the tensile test, considered here as the threshold of failure, confirming, as observed experimentally, that neither fracture nor necking is developed in the blank during the whole drawing process. Finally, the possibility to carry out a reduced two-step drawing process, obtained by merging the second and third steps of the three-step process, is precluded since the damage criterion predicts in this case excessively large values that indicate that failure may occur in specific zones of the sheet.     

Assessment of intradialysis calcium mass balance by a single pool variable‐volume calcium kinetic model

Introduction: A reliable method of intradialysis calcium mass balance quantification is far from been established. We herein investigated the use of a single‐pool variable‐volume Calcium kinetic model to assess calcium mass balance in chronic and stable dialysis patients. Methods: Thirty‐four patients on thrice‐weekly HD were studied during 240 dialysis sessions. All patients were dialyzed with a nominal total calcium concentration of 1.50 mmol/L. The main assumption of the model is that the calcium distribution volume is equal to the extracellular volume during dialysis. This hypothesis is assumed valid if measured and predicted end dialysis plasma water ionized calcium concentrations are equal. A difference between predicted and measured end‐dialysis ionized plasma water calcium concentration is a deviation on our main hypothesis, meaning that a substantial amount of calcium is exchanged between the extracellular volume and a nonmodeled compartment. Findings: The difference between predicted and measured values was 0.02 mmol/L (range ?0.08:0.16 mmol/L). With a mean ionized dialysate calcium concentration of 1.25 mmol/L, calcium mass balance was on average negative (mean ± SD ?0.84 ± 1.33 mmol, range ?5.42:2.75). Predialysis ionized plasma water concentration and total ultrafiltrate were the most important predictors of calcium mass balance. A significant mobilization of calcium from the extracellular pool to a nonmodeled pool was calculated in a group of patients. Discussion: The proposed single pool variable‐volume Calcium kinetic model is adequate for prediction and quantification of intradialysis calcium mass balance, it can evaluate the eventual calcium transfer outside the extracellular pool in clinical practice.     

Fast Quadtree/Octree adaptive meshing and re-meshing with linear mixed elements

Engineering with Computers - In this paper, we will focus on adaptive meshing and re-meshing. We present an original approach, based on Quadtree and Octree, to construct the initial mesh and refine...     

A new prefabricated external thermal insulation composite board with ceramic finishing for buildings retrofitting

Given the high energy consumption connected to old buildings and their large environmental impact, there is a strong need for effective solutions for the building envelope retrofitting. Among these solutions, external thermal insulation composite systems (ETICS) have found large application in recent decades. In this paper a new kind of large-size thermal insulation composite boards, prefabricated using porcelain stoneware slab finishing, was developed. Different thermal insulating materials and adhesives, with and without glass fibre mesh, were tested by both current methodologies and purposely designed tests, in order to assess their physical–mechanical properties and durability performance, finally selecting the most suitable materials for the composite board. The strong points of this composite board are mainly: (i) its short placing time and improved execution quality, due to prefabrication; (ii) its high aesthetical value; (iii) its high durability, as the finishing layer is mostly insensible to weathering. The results highlight the good performances of the prefabricated composite board developed in this study (generally higher than current ETICS). The testing procedure followed in this study is also meant to give a contribution to the establishment of methodologies for the selection and durability assessment of materials for the building envelope retrofitting.     

Mapping inland water carbon content with Landsat 8 data

Landsat 8 is the first Earth observation satellite with sufficient radiometric and spatial resolution to allow global mapping of lake CDOM and DOC (coloured dissolved organic matter and dissolved organic carbon, respectively) content. Landsat 8 is a multispectral sensor however, the number of potentially usable band ratios, or more sophisticated indices, is limited. In order to test the suitability of the ratio most commonly used in lake carbon content mapping, the green–red band ratio, we carried out fieldwork in Estonian and Brazilian lakes. Several atmospheric correction methods were also tested in order to use image data where the image-to-image variability due to illumination conditions would be minimal. None of the four atmospheric correction methods tested, produced reflectance spectra that matched well with in situ measured reflectance. Nevertheless, the green–red band ratio calculated from the reflectance data was in correlation with measured CDOM values. In situ data show that there is a strong correlation between CDOM and DOC concentrations in Estonian and Brazilian lakes. Thus, mapping the global CDOM and DOC content from Landsat 8 is plausible but more data from different parts of the world are needed before decisions can be made about the accuracy of such global estimation.     

Partial replacement of sodium chloride with potassium chloride in marinated rabbit meat

This study was aimed at evaluating the consequences of sodium chloride reduction by potassium chloride up to 50% on technological, sensorial and microbiological traits of marinated rabbit meat. In total, 226 rabbit loin meat samples were obtained and subjected to vacuum tumbling using solutions with different NaCl/KCl ratios. Replacing of sodium chloride up to 30% by potassium chloride did not change microbiological traits (total aerobic mesophilic and lactic acid bacteria maximum cell loads), sensorial acceptability (perceived saltiness and overall liking) and technological traits (pH, colour, texture, cooking loss and yield). Otherwise, reduction in sodium chloride to 50% significantly decreased perceived saltiness (4.15 vs. 4.73; P < 0.05) and reduced microbial shelf life by 1 day when compared to control, even if there was still no effect on technological traits. In conclusion, it is feasible imparting an added value for processed rabbit meat products by reduction in sodium content that could increase market interest.     

Organic Design of Massively Distributed Systems: A Complex Networks Perspective

The vision of Organic Computing addresses challenges that arise in the design of future information systems that are comprised of numerous, heterogeneous, resource-constrained and error-prone components. The notion organic highlights the idea that, in order to be manageable, such systems should exhibit self-organization, self-adaptation and self-healing characteristics similar to those of biological systems. In recent years, the principles underlying these characteristics are increasingly being investigated from the perspective of complex systems science, particularly using the conceptual framework of statistical physics and statistical mechanics. In this article, we review some of the interesting relations between statistical physics and networked systems and discuss applications in the engineering of organic overlay networks with predictable macroscopic properties.