一种新型排液方法——对井口实施降压

论述了在南得克萨斯州某油田的21口井安装井口压缩机装置取得了很好的排液效果。这些井安装了这种局部区域型低压集输系统后,气体的产量有了显著的提高,直接使油田获得了经济效益。还介绍了选井的条件和现场试验得到的经验与结论,可以对未来的工程起到预测和分析的作用。     

结合RDF实现对XML文档的RBAC

文章提出了一种面向XML文档的基于XMLschema并结合RDF的访问控制模型,它实现了对XML文档的细粒度的安全访问控制,同时提供了对XML文档中associationsecurityobject的安全访问控制。     

Laterally coupled buried heterostructure high-Q ring resonators

All-buried InP-InGaAsP ring resonators laterally coupled to bus waveguides are demonstrated. The buried configurations offer a lower built-in refractive index step along the resonator periphery, which affords enhanced optical coupling coefficients between the waveguides and reduced scattering losses caused by the resonator sidewall imperfections. Very low optical intensity attenuations of 0.4 cm/sup -1/ and coupling-limited quality factors of greater than 10/sup 5/ are observed from 200-/spl mu/m-radii ring resonators. The measured spectral linewidth is as narrow as 0.0145 nm.     

复合材料层合曲梁分层问题的解析解法

根据叠加原理将含有分层的复合材料层合曲梁在横向载荷作用下的受力状态分解为在面受力状态与出面受力状态,再将出面受力状态分解为无分层曲梁受横向载荷状态与含分层曲梁承受附加剪切载荷状态。将分层问题归结为在附加剪切载荷状态中,层合梁附加位移与附加应力的分析,并据此建立了一个简单的力学模型。最后得到了由分层引起的附加位移与应力的解析解答,并用能量释放率方法确定了应力强度因子。     

Wavelength and Waveband Assignment for Ring Networks Based on Parallel Multi‐granularity Hierarchical OADMs

In this paper we study the optimization issues of ring networks employing novel parallel multi‐granularity hierarchical optical add‐drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off‐line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large‐scale OADM networks.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

梯度材料电场辅助自蔓延燃烧合成机理研究

采用电场辅助自蔓延高温合成技术制备了SiC-TiC-xNi梯度功能材料.利用电场的焦耳加热效应,使那些通过单一自蔓延高温合成(SHS)技术难以进行或不能进行的反应物的制备得以实现;电场加快离子的扩散与迁移速度,减少晶体缺陷,使反应更加充分.实验发现,随着电场强度的增大,反应体系的温度升高、电流值变大.     

双相各向异性介质中的拟慢纵波研究

通过双相各向异性介质理论,利用弹性波传播方程,推导出三维双相各向异性介质中弹性波的Christoffel方程。在Christoffel方程基础上,分别计算并分析了频率、固流相耦合密度、渗透率对双相各向异性介质中拟慢纵波的相速度、衰减的影响。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。