Solutions of Falkner–Skan equation with heat transfer by Fourier series

In this paper, we solve the Falkner–Skan equation with heat transfer through an expansion in Fourier series, results are improved by incorporating an asymptotic analysis for the Fourier series coefficients. The results show that the classical expansion in Fourier series together with the incorporation of an asymptotic analysis for coefficients of the series delivers a solution with very good accuracy and rapid convergence when it is compared with other methods of solution found in the literature as finite difference and shooting method.     

Physicochemical,crystallinity, pasting and thermal properties of heat‐moisture‐treated pinhão starch

The effect of heat‐moisture treatment (HMT) on the properties of pinhão starches under different moisture and heat conditions was investigated. The starches were adjusted to 15, 20 and 25% moisture levels and heated to 100, 110 and 120°C for 1 h. The X‐ray diffractograms, swelling power, solubility, gel hardness, pasting properties and thermal properties of the native and HMT pinhão starches were evaluated. Compared to native starch, there was an increase in the X‐ray intensity and gel hardness of HMT starches, with the exception of the 25% moisture‐treated and 120°C heat‐treated starch. HMT reduced the swelling power and solubility of the pinhão starches when compared to native starch. There was an increase in the pasting temperature, final viscosity and setback and a decrease in the peak viscosity and breakdown of HMT pinhão starches compared to native starch. HMT increases the gelatinisation temperature of native pinhão starch and reduces gelatinisation enthalpy.     

Antimicrobial effects of silver nanoparticles against bacterial cells adhered to stainless steel surfaces

Given the increasing number of antibiotic-resistant bacteria and the need to synthesize new antimicrobials, silver has attracted interest in the scientific community because of its recognized antimicrobial activity. This study aimed to evaluate the antimicrobial effects of silver nanoparticles (NP) obtained by a new method and tested at concentrations of 6 μg/ml and 60 μg/ml against the species Staphylococcus aureus, Listeria innocua, Salmonella Choleraesuis, Pseudomonas aeruginosa, Escherichia coli, and Bacillus cereus. The ability of these nanoparticles to remove or kill vegetative cells adhered to stainless steel surfaces was also evaluated. We observed that the NP obtained with the new method, concentrated silver nanoparticles (CNP), and silver nanoparticles with added sodium chloride (NPNaCl) had high antimicrobial activities (P < 0.05). We also verified that the most effective condition for the removal of P. aeruginosa cells on stainless steel coupons (10 by 10 mm) was immersion of the surfaces in CNP. The CNP treatment produced a 5-log reduction of the microbial population after 30 to 60 min of immersion. The CNP treatment also performed better than water and sodium carbonate, a compound commonly applied in clean-in-place procedures in the food industry, in removing adherent B. cereus cells from stainless steel cylinders. Therefore, these results suggest that NP synthesized by a new procedure may be used as antimicrobials in the food industry, for example, for the sanitization of utensils that come into contact with foods.     

Resistant starch and thermal,morphological and textural properties of heat‐moisture treated rice starches with high‐, medium‐ and low‐amylose content

This study investigated the effects of heat‐moisture treatment (HMT) on the resistant starch content and thermal, morphological, and textural properties of rice starches with high‐, medium‐ and low‐amylose content. The starches were adjusted to 15, 20 and 25% moisture levels and heated at 110°C for 1 h. The HMT increased the resistant starch content in all of the rice starches. HMT increased the onset temperature and the gelatinisation temperature range (T_finish–T_onset) and decreased the enthalpy of gelatinisation of rice starches with different amylose contents. This reduction increased with the increase in the moisture content of HMT. The morphology of rice starch granules was altered with the HMT; the granules presented more agglomerated surface. The HMT affected the textural parameters of rice starches; the high‐ and low‐amylose rice starches subjected to 15 and 20% HMT possessed higher gel hardness.     

Plasmonic propagations distances for interferometric surface plasmon resonance biosensing

A surface plasmon resonance (SPR) scheme is proposed in which the local phase modulations of the coupled plasmons can interfere and yield phase-sensitive intensity modulations in the measured signal. The result is an increased traceability of the SPR shifts for biosensing applications. The main system limitation is the propagation distance of the coupled plasmon modes. This aspect is therefore studied for thin film microstructures operating in the visible and near-infrared spectral regions. The surface roughness of the substrate layer is examined for different dielectrics and deposition methods. The Au layer, on which the plasmonic modes are propagating and the biosensing occurs, is also examined. The surface roughness and dielectric values for various deposition rates of very thin Au films are measured. We also investigate an interferometric SPR setup where, due to the power flux transfer between plasmon modes, the specific choice of grating coupler can either decrease or increase the plasmon propagation length.     

Long‐range wireless sensor networks with transmit‐only nodes and software‐defined receivers

Wireless sensor networks for environmental monitoring and agricultural applications often face Long‐range requirements at low bit rates together with a large numbers of nodes. This paper presents the design and test of a novel wireless sensor network that combines a large radio range with very low power consumption and cost. Our asymmetric sensor network uses ultra‐low‐cost 40‐MHz transmitters and a sensitive software‐defined radio receiver with multi‐channel capability. Experimental radio range measurements in two different outdoor environments demonstrate a single‐hop range of up to 1.8 km. A theoretical model for radio propagation at 40 MHz in outdoor environments is proposed and validated with the experimental measurements. The reliability and fidelity of network communication over longer periods is evaluated with a deployment for distributed temperature measurements. Our results demonstrate the feasibility of the transmit‐only low‐frequency system design approach for future environmental sensor networks. Although there have been several papers proposing the theoretical benefits of this approach, to the best of our knowledge, this is the first paper to provide experimental validation of such claims. Copyright © 2011 John Wiley & Sons, Ltd.     

Reactive Processing of a ZrB2 / ZrC / Zr–Si Ceramic Composite with a Controlled Oxygen Potential

A Zr–Si liquid reacted with B₄C in a graphite enclosure was configured to control the oxygen potential (10^?45 kPa) to form a ZrB₂ / ZrC / Zr – Si ceramic composite. The graphite enclosure was placed in a temperature gradient with the hot zone at >2133 K to react Zr – Si with B₄C and with the opposite end approximating 933–1000 K at the position of an aluminum melt. A ZrB₂ / ZrC / Zr – Si composite forms with the scanning‐electron microscope (SEM), microstructures showing rectangular ZrB₂ precipitates and hexagonally shaped ZrC precipitates embedded in a Zr – Si matrix.     

Improved Thermal Behavior of Multiple Linked Arrays of Silicon Nanowires Integrated into Planar Thermoelectric Microgenerators

Low-dimensional structures have been shown to be promising candidates for enhancing the thermoelectric properties of semiconductors, paving the way for integration of thermoelectric generators into silicon microtechnology. With this aim, dense arrays of well-oriented and size-controlled silicon nanowires (Si NWs) obtained by the chemical vapor deposition (CVD)-vapor–liquid–solid (VLS) mechanism have been implemented into microfabricated structures to develop planar unileg thermoelectric microgenerators (μTEGs). Different low-thermal-mass suspended structures have been designed and microfabricated on silicon-on-insulator (SOI) substrates to operate as microthermoelements using p-type Si NW arrays as the thermoelectric material. To obtain nanowire arrays with effective lengths larger than normally attained by the VLS technique, structures composed of multiple ordered arrays consecutively bridged by transversal microspacers have been fabricated. The successive linkage of multiple Si NW arrays enabled the development of larger temperature differences while preserving good electrical contact. This gives rise to small internal thermoelement resistances, enhancing the performance of the devices as energy harvesters.     

A high energy Li-ion battery based on nanosized LiNi0.5Mn1.5O4 cathode material

The electrochemical performance of a Li-ion battery made from nanometric, highly crystalline LiNi_0.5Mn_1.5O₄ as positive electrode and mesoporous carbon microbeads (MCMBs) as negative electrode was assessed. The best performance was obtained by using a slight excess of spinel (a cathode/anode mole ratio of 1.3) and lithium bis-oxalate borate (LiBOB) instead of LiPF₆ as an electrolyte salt. Higher spinel contents caused the formation of metallic Li in the carbon and the rapid degradation of battery performance as a result. The calculated output energy was 322 Wh kg⁻¹ which is higher than the value reported for the LiMn₂O₄/C cell (250 Wh kg⁻¹).