Crystallization of Li2O · Al2O3· 6SiO2 Glasses Containing Niobium Pentoxide as Nucleating Dopant

Niobium pentoxide (T form, orthorhombic system) was utilized to promote devitrification in Li₂O · Al₂O₃· 6SiO₂ glasses. Two or more mole percentage of this nucleating dopant enhanced crystallization in these glasses. Glasses containing 4.0 and 8.0 mol% T-Nb₂O₅ exhibited a high tendency to form dispersed TT-Nb₂O₅ (monoclinic system) precipitates during the glass quenching process. The crystallization process in glasses containing 2.0 or 4.0 mol% T-Nb₂O₅ occurred as microphase separation, followed by the formation of dispersed TT-Nb₂O₅ crystalline precipitates (760°C), followed by β-quartz solid-solution ( ss ) formation (850° to 900°C) heterogeneously nucleated from the precipitates. β-quartz( ss ) transformed to β-spodumene( ss ), along with a polymorphic transition from the TT-Nb₂O₅ to M-Nb₂O₅ (tetragonal system) crystalline phase.     

Behavior of high strength concrete with and without steel fiber reinforcement in triaxial compression

Based on an extensive experimental program, this paper studies the behavior of high strength concrete and steel fiber reinforced high strength concrete under uniaxial and triaxial compression. Triaxial stress-strain relations and failure criteria are used to evaluate the effect of steel fiber reinforcement on the mechanical properties of high strength concrete in triaxial compression, which is found to be insignificant.     

A novel synthesis method for the preparation of aromatic poly(imide benzoxazole) from trimellitic anhydride chloride and bis(o‐aminophenol)

A poly(imide benzoxazole) was prepared directly from trimellitic anhydride chloride and 2,2‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane (BisAPAF) monomers in a two‐step method. In the first step, a poly(hydroxyamide amic acid) precursor was synthesized by the low‐temperature solution polymerization in an organic solvent. Subsequently, thermal cyclodehydration of the poly(hydroxyamide amic acid) precursor at 350°C produced the corresponding poly(imide benzoxazole). The inherent viscosity of the precursor polymer was 0.22 dL/g. The cyclized poly(imide benzoxazole) showed a glass transition temperature (T_g) at 329°C and a 5% weight loss temperature at 530°C in nitrogen and at 525°C in air. The poly(imide benzoxazole) is amorphous as evidenced by the wide‐angle X‐ray diffraction measurement. The structures of the precursor polymer and the fully cyclized polymer were characterized by Fourier transform infrared (FTIR) and proton nuclear magnetic resonance spectroscopy (¹H NMR). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2388–2391, 2003     

纳米线/模板共构染料敏化二氧化钛太阳电池的制备

以清洁、制备过程简单、成本低廉的阴极电弧离子镀在低温成长染料敏化二氧化钛太阳能电池的二氧化钛模板,从模板上利用水热法生长出二氧化钛纳米线,形成理想的染料敏化太阳电池异质接面,具有高比表面积并利于染料的吸收,从而提升电池效率.最后加以封装成ITO glass/AIP-TiO2/[TiO2-nanowire(N3 dye)]/I2 LiI electrolyte/Pt/ITO glass太阳能电池组件,探讨了其微观结构对染料敏化二氧化钛太阳能电池光电转换效率的影响.     

1-甲基-3-(7-氟-4-炔丙基-1,4-苯并噁嗪-3-酮-6-基)-1,3-喹唑啉-2,4-二酮的合成及其除草活性

标题化合物(SYP-298)是沈阳化工研究院的试验除草剂,由邻硝基苯甲酸经5步反应制得。其结构经核磁共振谱和质谱分析确证。SYP-298在温室条件下38 g a.i./hm2可防多种阔叶杂草,在600 g a.i./hm2对玉米和水稻安全。     

Physical gelation of crystallizing metallocene and Ziegler-Natta ethylene-hexene copolymers

The effect of molecular architecture on the evolution of viscoelastic properties during crystallization was investigated using ethylene-hexene copolymers manufactured via metallocene (M-LLDPE) and Ziegler-Natta (ZN-LLDPE) processes. Differences in branching distribution were shown to have a drastic effect on the viscoelastic properties near the gel point. It is shown that the branching distribution rather than branch content is the determining parameter for the evolution of the rheological properties during isothermal and non-isothermal crystallization, and for the width of the solidification interval. We developed a partial melting technique for the preparation of stable critical gels of LLDPE whose viscoelastic properties correspond to the intermediate state between melt and solid. Local molecular conformation and crystallinity in these gels were characterized by Raman spectroscopy, which shows that the transition from melt-like to solid-like rheological behavior (physical gelation) in LLDPE occurs at a very low overall crystallinity of less than 5%.     

Processing, Microstructure, and Wear Behavior of Silicon Nitride Hot-Pressed with Alumina and Yttria

Commercial silicon nitride powder with A1₂O₃ and Y₂O₃ additives was hot-pressed to complete density. The resulting microstructure contained elongated grains with no trace of remaining α-Si₃N₄. The aspect ratio of the elongated grains increased with increasing soak time at a fixed hot-pressing temperature. X-ray diffraction analysis showed that the crystalline phase in the hot-pressed samples was β-sialon (Si_6−zAl_zO_zN_8−z) with z values that increased with soak time. The fracture strength and fracture toughness of the samples increased as the aspect ratio of the grains increased. The Vickers hardness decreased slightly as the soak time was increased, which was attributed to a grain size effect. Wear tests of silicon nitride against silicon nitride were conducted on a reciprocating pin-on-disk apparatus with paraffin oil as a lubricant. Correlation studies of wear with microstructure and mechanical properties were performed. The wear rate increased rapidly with increasing soak time in spite of the increased strength and toughness. This was attributed to increased third-body wear caused by pullout of pieces from the wear surface. The pullout mechanism was not conclusively identified. However, TEM examination showed clear evidence of dislocation motion under the wear scar. Grain boundary microstresses caused by the anisotropic thermal expansion and elastic properties of the elongated grains may have contributed to the observed pullout.     

Effects of molecular weight and molecular structure of low profile additives on the properties of bulk molding compound (BMC)

The effects of molecular weight and molecular structure of styrene(St)‐based and vinyl acetate(VAc)‐based low‐profile additive (LPA) on the curing kinetics and compatibility of unsaturated polyester (UP)/LPA system and linear shrinkage, water absorption rate, surface gloss and pigmentability of bulk molding compound (BMC) were investigated. Results show that the curing reaction rate decreases with an increase of the molecular weight of LPA due to the chain entanglement effect. The plasticizing effect of LPA on the (UP) network was reduced with an increase of the molecular weight of LPA. Water absorption of BMC increases as the molecular weight of LPA increases, implying that more microvoids were formed inside the BMC, resulting a lower linear shrinkage rate, and worse pigmentability. However, good shrinkage control LPA does not necessarily lead to a smoother surface and better surface gloss. Furthermore, modified LPAs possess better compatibility with UP, the final curing conversion of UP is elevated, and both better shrinkage control and surface properties are also observed.     

Phase behavior of ternary polymer blends with favorable interactions

Atactic poly(methyl methacrylate) (aPMMA) and poly(vinyl pyrrolidone) (PVP) with a weight‐average molecular weight of 360,000 g/mol were found to be immiscible on the basis of preliminary studies. Poly(styrene‐co‐vinyl phenol) (MPS) with a certain concentration of vinyl phenol groups is known to be miscible with both aPMMA and PVP. Is it possible to homogenize an immiscible aPMMA/PVP pair by the addition of MPS? For this question to be answered, a ternary blend consisting of aPMMA, PVP, and MPS was prepared and measured calorimetrically. The role of MPS between aPMMA and PVP and the effects of different concentrations of vinyl phenol groups on the miscibility of the ternary blends were investigated. According to experimental results, increasing the vinyl phenol contents of MPS has an adverse effect on the miscibility of the ternary blends. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2064–2070, 2005     

Isothermal crystallization kinetics and melting behavior of nylon/saponite and nylon/montmorillonite nanocomposites

DSC thermal analysis and X‐ray diffraction have been used to investigate the isothermal crystallization behavior and crystalline structure of nylon 6/clay nanocomposites. Nylon 6/clay has prepared by the intercalation of ε‐caprolactam and then exfoliating the layered silicates by subsequent polymerization. The DSC isothermal results reveal that introducing saponite into the nylon structure causes strongly heterogeneous nucleation induced change of the crystal growth process from a two‐dimensional crystal growth to a three dimensional spherulitic growth. But the crystal growth mechanism of nylon/montmorillonite nanocomposites is a mixed two‐dimensional and three‐dimensional spherulitic growth. The activation energy drastically decreases with the presence of 2.5 wt % clay in nylon/clay nanocomposites and then slightly increases with increasing clay content. The result indicates that the addition of clay into nylon induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). The correlation among crystallization kinetics, melting behavior, and crystalline structure of nylon/clay nanocomposites is also discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2196–2204, 2004