Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

APP软件性能效率研究

性能效率是APP软件的重要质量属性，但目前缺乏APP软件性能效率的通用模型。分析了APP软件的性能特征，基于ISO/IEC 25010标准提出了APP软件的性能效率模型，定义了APP软件性能效率的子特性和度量指标。基于提出的APP软件性能效率模型，通过实验对APP软件的性能效率进行了度量及相关分析。     

Influence of geosynthetic reinforcement on the stability of an embankment with rigid columns embedded in an inclined underlying stratum

Incompressible dipping substrata are commonly encountered in engineering practice. Compared to horizontal underlying strata, the inclined underlying stratum increase the risk of collapse of embankments reinforced with columns because it weakens the restraint of the column base. The objective of this study is to investigate the effectiveness of geosynthetics on improving the embankment stability when the underlying stratum is inclined. The influence of geosynthetic tensile stiffness on the ultimate surcharge and failure mechanism is studied. A deep-seated failure with column tilting occurs when the geosynthetic tensile stiffness is low, whereas a lateral sliding occurs when the geosynthetic tensile stiffness is high. To illustrate the contribution of geosynthetics, the distribution of the lateral pressures acting on the columns is analyzed.     

Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.     

Experimental Study of Oilfield Water Plugging with Organic Chromium Gel

Chemistry and Technology of Fuels and Oils - Application of water flooding technologies in the oilfield causes intensive heterogeneity of the oil reservoir and improper circulation of the injected...     

Structural,optical and electrical properties of indium doped Cu2ZnSn(S,Se)4 thin films synthesized by the DC and RF reactive magnetron cosputtering

Element doping into the Cu₂ZnSn(S,Se)₄ (CZTSSe) absorber is an effective method to optimize the performance of thin film solar cells. In this study, the Cu₂In_xZn_1-xSn(S,Se)₄ (CIZTSSe) precursor film was deposited by magnetron cosputtering technique using indium (In) and quaternary Cu₂ZnSnS₄ (CZTS) as targets. Meanwhile, the In content was controlled using the direct current (DC) power on In target (P_In). A single kesterite CIZTSSe alloy was formed by successfully doping a small number of In³⁺ into the main lattice of CZTSSe. The partial Zn²⁺ cations were substituted by In³⁺ ions, resulting in improving properties of CZTSSe films. Morphological analysis showed that large grain CIZTSSe films could be obtained by doping In. The well-distributed, smooth, and dense film was obtained when the P_In was 30 W. The band gap of CIZTSSe could be continuously adjusted from 1.27 to 1.05 eV as P_In increased from 0 to 40 W. In addition, the CIZTSSe alloy thin film at P_In = 30 W exhibited the best p-type conductivity with Hall mobility of 6.87 cm²V^?1s^?1, which is a potential material as the absorption layer of high-performance solar cells.