爆炸箔起爆系统初始电阻对爆发电流和飞片速度影响的数值模拟

研究了电爆炸箔起爆系统起爆回路初始电阻对爆发电流和冲击片雷管飞片速度的影响规律，分析了影响电爆炸箔起爆系统体系的因素，为在可靠发火条件下降低起爆系统体积提供设计参考。     

横管初冷器液体喷洒系统的改进

介绍了横管初冷器液体喷洒系统存在的问题，改进方法及效果。     

带疏水泵加热器出口主凝结水焓的计算方法

以火电厂热力系统热力单元矩阵分析法为基础，提出了一种更为科学有效的带疏水泵加热器出口主凝结水焓分析计算的新方法，应用表明，其结论与常规算法完全一致，图2表1参3。     

A transmit/receive IF chip set for WCDMA mobiles in 0.35 /spl mu/m CMOS

An implementation of the IF section of WCDMA mobile transceivers with a set of two chips fabricated in an inexpensive 0.35-/spl mu/m two-poly three-metal CMOS process is presented. The transmit/receive chip set integrates quadrature modulators and demodulators, wide dynamic range automatic gain control (AGC) amplifiers, with linear-in-decibel gain control, and associated circuitry. This paper describes the problems encountered and the solutions envisaged to meet stringent specifications, with process and temperature variations, thus overcoming the limitations of CMOS devices, while operating at frequencies in the range of 100 MHz-1 GHz. Detailed measurement results corroborating successful application of the new techniques are reported. A receive AGC dynamic range of 73 dB with linearity error of less than /spl plusmn/2 dB and spread of less than 5 dB for a temperature range of -30/spl deg/C to +85/spl deg/C in the gain control characteristic has been measured. The modulator measurement shows a carrier suppression of 35 dB and sideband/third harmonic suppression of over 46 dB. The core die area of each chip is 1.5 mm/sup 2/.     

In—situ Composite Based on Poly （ethylene terephthalate）,Polyamide and Polyethylene with Microfibres Formed through Extrusion and Hot Stretching

In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA),and continuous Polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter.The extrudate was drawn at a drawing ratio of 3.1,and then quickly cooled in cold water.The specimens were obtained by injection molding at processing temperatures less than 190℃，far below the melting temperature of PET (265℃) and PA (230℃),which can maintain the solid state of PET and PA microfiber phase in the composites.Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0-20 wt pct PET or PA),and especially,PET and PA were almost deformed into fibers at the concentration of 15wt pct.Eensile strength and especially.PET and PA were almost deformed into fibers at the concentration of 15wt pct.Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results.The most noticeable improvement of the tensile properties occurred at 15wt pct of PET in PET/PE system,corresponding to the highest microfiber content,where the tensile strength reached 32.5 MPa,whereas only 19.5 MPa for the pure PE.     

轻钢结构屋面的应用

针对轻钢结构构屋面系统的性能、特点、构造和施工方法进行了论述，介绍了与传统建筑形成对照的一种新型结构形式，使传统的重盖、肥梁、胖柱、色彩单一的建筑状况得到改善。轻钢结构的优点将使它的生产规模、适用范围不断扩大，从而以其漂亮的外和合理的造价美化人类的生活环境。     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

环境因素对碳钢点蚀临界电势的影响

采用动电势扫描法测定了不同体系中碳钢发生点蚀的临界电势Eb。结果表明 :当Cl- 浓度 <0 .0 1mol/L时 ,随Cl- 浓度增加 ,临界电势负移并与Cl- 浓度成线性关系 ;pH值在 7～ 11之间 ,随pH值增加 ,临界电势正移并与pH值成线性关系 ;随温度增加 ,临界电势负移并与温度成线性关系。     

TOP开关电源的设计与制作

利用TOP开关器件设计了一种高精度，输出电压可调的开关电源，并介绍了制作方法。     

36 m 高砖砌水塔定向折叠爆破拆除

介绍了复杂环境中砖砌高大水塔的定向折叠爆破拆除.根据周围的环境情况,在施工中采用了开定向窗、挖定位坑等技术措施,确保爆破成功,达到了设计效果.