论制造企业的信息安全建设

阐述企业信息安全隐患及主要安全技术的阐述,结合本人工作的企业做案例分析。     

浅谈变频器供电条件下电动机的温升与对策

随着变频调速技术的蓬勃发展，变频器供电电机的温升问题已引起人们的广泛关注。本文首先讨论了电动机的温升限度；然后结合感应电机温升实验的相关数据分析了变频器供电对电动机温升的影响及其原因；最后从降低发热量和提高散热能力两方面提出缓解电机温升的措施，并指出了实际应用中应注意的问题。     

复肥生产过程中缩二脲的生成研究

采用国家化工行业标准(HG 2095-91) - 涂层尿素中缩二脲含量的测定方法系统研究了复混肥生产过程中缩二脲的生成,通过实验研究分析发现,在影响缩二脲生成率的4个因素:物料加热温度、加热时间、物料中水份含量、物料中尿素的质量分数中,影响最显著的是尿素的质量分数.     

超低碳奥氏体不锈钢00Cr18Ni10还原脱磷研究

在 2 5kg真空感应炉上用镁钙合金对超低碳奥氏体不锈钢 0 0Cr18Ni10进行了还原脱磷试验。通过充入工业纯氩使炉内压力为 6 6 .6 6kPa和精炼时的反应温度 14 5 0～ 15 0 0℃ ,加入镁钙合金 5 0kg t和助熔剂CaF2 11kg t,可使精炼后 0 0Cr18Ni10的磷含量进一步降低到 (5 0～ 6 0 )× 10 - 6 ,钢中氧、硫含量分别稳定降到(4～ 6 )× 10 - 6 和 15× 10 - 6 。     

Synthesis and aqueous solution behaviors of sodium sulfonate‐terminated dendritic poly(ester‐amine)

Sodium sulfonate‐terminated dendritic poly(ester‐amine) (SPEA) was synthesized by sulfonation of acrylic double bond‐terminated dendritic poly(ester‐amine) (APEA) with sodium hydrogen sulfite (NaHSO₃) in mixture of diglycol and 2‐butanone under normal pressure. The structure of SPEA was characterized by IR, ¹H‐NMR, and elemental analysis. SPEA was water‐soluble. 1.0–40.0% (mass) SPEA aqueous solutions appeared as dilatant fluid. When pH value varied from 1.5 to 12.0, the viscosity of 1–5% (mass) SPEA aqueous solutions changed very small, and the electric conductivity almost kept stable within pH 3.0–10.0. The relationship between the viscosity and the concentration of SPEA water solutions was similar to that of NaCl water solutions. The surface tension of SPEA water solutions was lower than that of polyethylene glycol 2000 water solutions with the same concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

用激光烧结法制备的SnO2薄膜的气敏性质

用溶胶-凝胶法制备SnO2前驱液,然后用提拉法分别在单晶Si和Al2O3基片表面制备出SnO2前驱膜,再用脉冲Nd:YAG激光烧结前驱膜使其转变为晶体SnO2薄膜.用XRD分析了单晶Si表面的SnO2薄膜,研究激光功率对SnO2薄膜相组成的影响.TEM观察表明,激光烧结后的薄膜SnO2颗粒均匀,直径约为10 nm.用激光烧结法制备的SnO2薄膜对浓度为1.80×10-4丙酮的最高灵敏度为30～40,明显高于用传统烧结法制备的SnO2薄膜的灵敏度.激光烧结能降低薄膜具有最高灵敏度的工作温度.     

Performance evaluation on a double‐layered satellite network

How to evaluate the performance of satellite networks is a prerequisite to the construction of satellite networks, and is also one of challenges in the researches on satellite networks. In this paper, generalized stochastic Petri net (GSPN) models are presented to carry out the performance analysis of a double‐layered satellite network. Firstly, the GSPN model of a double‐layered satellite network is simplified by proper analysis. Then, two sets of experiments are conducted to analyse the performance of the satellite networks, and show that the double‐layered satellite network outperforms single‐layered ones on the heavy traffic load. Finally, the feasibility and effectiveness of the proposed approach is verified by simulation experiments. Copyright © 2005 John Wiley & Sons, Ltd.     

饮用水中挥发性三卤甲烷(THM)_s测定方法的改进

本文使用吹扫捕集法来前处理水样,用带有电子捕获检测(ECD)的气相色谱仪来测定水中三卤甲烷(THM)_s。水样加标回收率在85%～115%之间,相对标准偏差在5%左右。实验结果表明,该法具有简单、快速、灵敏的特点。     

乙烯裂解炉辐射段炉顶密封结构优化设计

乙烯裂解炉的炉顶密封效果关系到装置的安全、稳定运行.针对现行的密封结构,进行了合理的技术改造和优化设计,并经实际投入使用,效果良好,也可进一步推广到类似的炉型上.