Dissolution of phase-separated domains after a jump to a temperature in the single-phase region

Phase-separated domains prepared in the two-phase region were dissolved at a temperature in the single-phase region, and their dissolution dynamics was studied by using the time-resolved light scattering (TRLS) technique and a scanning electron microscope (SEM). The time t_ps of preparation of domains was chosen to be long enough for phase separation to proceed into the late stage. The scattered light intensity at small wavenumbers increased before it attenuated. As t_ps increased, the increase at smaller wavenumbers became more significant and the peak intensity decreased only slightly with dissolution time. The characteristic wavenumber q_m evaluated from TRLS and SEM followed the power-law relation q_mt^−0.3.     

Furnace grown gate oxynitride using nitric oxide (NO)

Gate oxynitride was grown in NO for the first time. This approach can provide a tight N accumulation near the Si/SiO₂ interface. Much lower thermal budget is required for an NO process than for an N₂O process to produce an oxynitride with useful properties. Submicron MOSFET's with NO oxynitride showed superior current drive characteristics and comparable hot carrier immunity to those with N₂O oxynitride     

Superconductivity in W-containing diamond-like nanocomposite films

Superconductivity in a tungsten-containing carbon-oxide film was reported. The film with 500 nm thickness was deposited onto polycrystalline silicon oxides using chemical vapor deposition and the co-sputtering of a tungsten metal target. The bonding state of the carbon atoms and the macroscopic and microscopic crystal structure of the film were investigated by Raman spectroscopy, X-ray diffraction and transmission electron microscopy measurements. From the experimental results, we determined that this film essentially had an amorphous structure. The temperature dependence on resistivity was measured in the temperature range of 2–300 K. Resistive superconducting transition was observed at 3.8 K. The dc magnetizations were measured in the temperature range of 1.8–6.5 K. The diamagnetism resulting from a superconductive state was observed below 3.75 K, which is consistent with a resistive superconducting transition. It is thought that the finite sized clusters of the different superconductive transition temperatures cooperatively produce a macroscopic superconducting phenomenon.     

Improvements of the T-Ω method for 3-D eddy currentanalysis

An improved T-Ω method that can analyze magnetic fields produced not only by eddy currents but also by magnetizing currents is proposed. The method is applied to the analysis of 3-D eddy-current models with holes. The usefulness of the method is investigated by comparing calculated results with measured results and with results obtained by the A-Φ method. The T-Ω method has the advantage that the CPU time can be considerably reduced when most of the analyzed region is current-free and the eddy current flows two-dimensionally. The method is especially effective when the shape of the winding is simple and the distribution of magnetizing current is known beforehand. It is not effective when most of the analyzed region is current-carrying     

水平管气力输送数值模拟

本文采用粒子追踪理论对水平管中粒子流动状态进行了数值模拟.文中提出了一种新的粒子碰撞模型,并忽略粒子的旋转和扬力,仅考虑气流阻力和重力对粒子的影响,在输送量为9.13×10~3kg/s,混合比约0.3的条件下,通过数值计算得知:由于粒子间的碰撞,使得异径粒子的速度趋向平均化;粒子间的碰撞是粒子悬浮的原因之一;粒子的浓度沿管轴向是随时间而发生变化的.     

Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.     

Characterization of C-S-H from Highly Reactive β-Dicalcium Silicate Prepared from Hillebrandite

β-dicalcium silicate synthesized by thermal dissociation of hydrothermally prepared hillebrandite (Ca₂(SiO₃)(OH)₂) exhibits extremely high hydration activity. Characterization of the hydrates obtained and investigation of the hydration mechanism was carried out with the aid of trimethylsilylation analysis, ²⁹Si magic angle spinning nuclear magnetic resonance, transmission electron microscopy selected area electron diffraction, and XRD. The silicate anion structure of C-S-H consisted mainly of a dimer and a single-chain polymer. Polymerization advances with increasing curing temperature and curing time. The C-S-H has an oriented fibrous structure and exhibits a 0.73-nm dreierketten in the longitudinal direction. On heating, the C-S-H dissociates to form β-C₂S. The temperature at which βC₂S begins to form decreases with increasing chain length of the C-S-H or as the Ca/Si ratio becomes higher. The high activity of β-C₂S is due to its large specific surface area and the fact that the hydration is chemical-reaction-rate-controlled until its completion. As a result, the hydration progresses in situ and C-S-H with a high Ca/Si ratio is formed.     

Optical bistability and set-reset operation of a Fabry-Perotsemiconductor laser amplifier with two detuned light injections

Optical bistability in a Fabry-Perot semiconductor laser amplifier when two optical inputs detuned from the resonant wavelength of a semiconductor laser amplifier are injected is discussed. A split branch is found in the optical output versus input characteristics in addition to conventional optical bistability behavior. It is shown analytically and experimentally that set and reset can be achieved in the optical output of the semiconductor laser amplifier for each wavelength by applying two detuned optical pulses and using the split branch