A study of the corrosion properties of plasma nitrocarburized and oxidized AISI 1020 steels

Plasma nitrocarburized AISI 1020 steels were oxidized for 15, 30 and 60 min to evaluate their corrosion and microstructural properties. After plasma nitrocarburizing for 3 h at 570°C in a gas mixture comprising 85 vol.% N₂, 12vol.% H₂ and 3 vol.% CH₄, the compound layer composed of ɛ-Fe_2–3(N,C) and γ’-Fe₄(N,C) phases and the diffusion layer above the matrix were observed. The top oxide layer, consisting mainly of magnetite (Fe₂O₄) and hematite (Fe₂O₃) phases, forms after post-oxidation treatment at 500°C. However, the oxide layer was severely degraded by spallation as a result of increases in post-oxidizing time. The difference in corrosion resistance should be attributed to the thickness of the top oxide layer, which was governed by post-oxidizing time.     

New Process for the Preparation of Monodispersed, Spherical Silica Particles

A new method is presented for preparing highly monodispersed silica particles using a two-stage semibatch/batch hydrolysis reaction of Si(OC₂H₅)₄. The slower rate of hydrolysis of the tetraethylorthosilicate (TEOS) that occurred during the semibatch process resulted in larger silica particles with a higher yield and narrower size distribution. This was in direct contrast to the batch process. In addition, the ability of four different mixed processes to produce silica particles with good packing density, narrower particle-size distribution, and higher yield were evaluated. These were batch/batch (B-B), batch/semibatch (B-S), semibatch/batch (S-B), and semibatch/semibatch (S-S) processes. The S-S system produced the largest particles with the highest yields. The size of the silica particles obtained by the S-B method decreased with increasing reaction time, while the particles obtained by the B-S process had the best particle-size distribution and packing density. In conclusion, a mixed batch/semibatch system was the best way to produce an extremely narrow particle-size distribution and a good packing density.     

Oxidative stability of high-fatty acid rice bran oil at different stages of refining

The contents of natural antioxidants and the oxidative stability of rice bran oils at different refining steps were determined. Tocopherols and oryzanols were constant in crude and degummed oils but decreased in alkali-refined, bleached and deodorized oils. The process of degumming, alkali-refining, bleaching and deodorization removed 34% of the tocopherols and 51% of the oryzanols. During storage of deodorized oil for 7 wk, 34% of the tocopherols and 19% of the oryzanols were lost. The maximum weight gain, peroxide value and anisidine value were obtained from alkali-refined oil during storage. The order of oxidation stability was crude ≥ degummed > bleached = deodorized > alkali-refined oil.     

NO emission of oxygen-enriched CH4/O2/N2 premixed flames under electric field

This work investigates the electric field effect on nitrogen oxide (NO) pollutant formation and emission composition of premixed flames in order to provide better insight on the mechanism of controlling the combustion process by electro-physical means. The present study aims to investigate experimentally the effect of radial DC electric field on premixed laminar methane flame. The electric field effect on flame shape, emission composition and NO emission index of flame is investigated experimentally under the action of direct-current electric field under varying equivalence ratio and level of oxygen enrichment. The results show that ionic wind effects cause the distortion in flame shape. The ionic wind effects diminish with increasing flow rate and level of oxygen enrichment. Minimal effects on NO are measured for flames under the influence of electric field and vanished as the level of oxygen enrichment is increased. This was well supported by the temperature profile measurement in the post flame gas showing no field-induced modification also. It seemed that the action of an electric field on a flame with a geometry that remains practically undeformed produces very minimal effect on pollutant emission.     

An apparent kinetic model for the carbonation of calcium oxide by carbon dioxide

For the apparent kinetics of the carbonation reaction of calcium oxide by carbon dioxide, as a kind of noncatalytic gas–solid reaction, a model equation has been proposed as follows: X=kbt/(b+t), where X is the conversion of CaO; k, a kinetic rate constant (time⁻¹); b, a constant (time) equivalent to the time taken to attain half the ultimate conversion of CaO, and t, the time. As a result of analyses for some literature-reported data of CaO-carbonation conversion, it has been found that the rate of the carbonation can be well represented by dX/dt=k(1−X/X_u)², where X_u is the ultimate conversion of CaO, which is given by the product of two parametric constants, k and b. The constants k and b in the two rate control regimes of CaO-carbonation, chemical reaction control and diffusion control, have been determined as functions of temperature, respectively. The activation energy in the carbonation of surface CaO with CO₂ is estimated to about 72 kJ/mol regardless of the sources of CaO, however, that in the diffusion control regime appears differently as 102.5 (mesoporous CaO) or 189.3 kJ/mol (commercial-available CaO), possibly due to the morphological differences of the two CaO samples. From a practical point of view, the simple model equation proposed in this study deserves attention in that the CaO-carbonation behavior at working temperatures higher than 700 °C could be closely predicted.     

Feasibility of Sludge Ozonation for Stabilization and Conditioning

A pilot-scale sludge treatment plant was built to investigate the feasibility of ozonation processes for waste activated sludge treatment. Ozonation of wastewater sludge resulted in mass reduction by mineralization as well as by supernatant and filtrate recycle. Another advantage of sludge ozonation is a significant improvement of settleability and dewaterability. Experimental results showed that mass reduction of 70% and volume reduction of 85% compared with the control sludge was achieved through the sludge ozonation at a dose of 0.5?gO₃/gDS. It is also interesting to note that the filterability deteriorates up to ozone dose of 0.2?gO₃/gDS and then improves considerably at a higher ozone dose. The filterability could be improved by chemical conditioning even at a low ozone dose. The economic feasibility by cost analysis reveals that ozonation processes can be more economical than other alternative processes for sludge treatment and disposal at small-sized wastewater treatment plants.     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

Microwave Dielectric Properties of (1−x)(Na1/2Nd1/2)TiO3−xLa(Mg1/2Ti1/2)O3 via Ordering and Far IR Reflectivity Spectra

Microwave dielectric properties of (1− x )(Na_1/2Nd_1/2)TiO₃(NNT)− x La(Mg_1/2Ti_1/2)O₃(LMT) system have been investigated with focus on structural ordering and far IR reflectivity spectra. A single perovskite phase was found to exist with various superlattice reflections over the entire compositional range. 1:1 ordering observed in the (111) reflection of X-ray diffraction patterns was found to progress significantly in the specimens above x =0.8. The ordering characteristics that presumably related to B-site Mg/Ti ordering were assumed to affect favorably the quality factor at microwave frequencies. The increase of the quality factor also could be explained in terms of the decrease of lattice anharmonicity with LMT by analysis of far IR reflectivity spectra. As expected from the values of pure NNT and LMT, the dielectric constant and the temperature coefficient of frequency tended to gradually decrease with increasing LMT content.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

An Experimental Study of Fatigue Strength for Adhesively Bonded Tubular Single Lap Joints

In this paper, manufacturing technology of the tubular single lap adhesive joint was studied to obtain reliable and optimal joint quality. In addition, a surface preparation method and a bonding process for the joint were devised. The effect of the adhesive thickness and the adherend roughness on the fatigue strength of the joint was experimentally investigated. From experiments, it has been found that the fatigue strength of the joint increased as the adhesive thickness decreased and the optimal arithmetic surface roughness of the adherends was about 2 μm.