Crystal plasticity modeling of deformation and creep in polycrystalline Ti-6242

This paper develops an experimentally validated computational model based on crystal plasticity for the analysis of two-phase α/β Ti-6242 polycrystalline alloys. A rate-dependent elastic-crystal plasticity model is incorporated in this model to accommodate anisotropy in material behavior and tension-compression asymmetry inherent to this alloy. A combination of microtesting, orientation imaging microscopy, computational simulations, and minimization process, involving genetic algorithms, is implemented in this study for careful characterization and calibration of the material parameters. Size effects are considered in this analysis through a simple scaling process. A homogenized equivalent model of the primary α with transformed β colonies is developed for incorporation in the Ti-6242 FE model. The polycrystalline Ti-6242 computational model incorporates accurate phase volume fractions, as well as statistically equivalent orientation distributions to those observed in the orientation imaging microscopy scans. The effects of orientation, misorientations, and microtexture distributions are investigated through simulations by this computational model. The model is used to simulate constant strain rate and creep tests in compression and tension, and the results are compared with experiments. The effects of microstructure and creep-induced load-shedding on the localization of microstructural stresses and strains are studied for potential crack initiation criteria.     

A kinematic analysis of the modified flight telerobotic servicer manipulator system

A reverse analysis of a 6 degree of freedom (dof) subchain of a modified 7 dof flight telerobotic servicer (FTS) manipulator system is presented. The 6 dof subchain is designated as a TR-RT* chain. At the outset, it was considered that the reverse analysis would be similar to a TTT manipulator analyzed previously for which the third and fourth joints intersect at a finite point. This was not, however, the case and a sixteenth-degree tan-half-angle polynomial was derived for the TR-RT manipulator. The elimination procedure is interesting and much simpler than the procedures for the general case.     

Mössbauer effect studies and X-ray diffraction analysis of cobalt ferrite prepared in powder form by thermal decomposition method

Cobalt ferrite (Co_xFe_3?xO₄) is prepared in powder form by thermal decomposition of iron and cobalt salts and is analysed by X-ray diffraction and Mössbauer spectroscopic techniques. The variation of Mössbauer parameters, lattice parameters and crystallite size of the products formed with variation in the composition of Fe and Co ratios are studied. The studies confirm the formation of nano-size cobalt ferrite particles with defect structure and it is found to be maximum for the Fe : Co = 60 : 40 ratio of the initial precursor oxides.     

Efficient Computation of EXIT Functions for Nonbinary Iterative Decoding

The calculation of nonbinary extrinsic information transfer charts for the iterative decoding of concatenated index-based codes is addressed. We show that the extrinsic information at the output of a constituent a posteriori probability decoder can be calculated with very low complexity, where expensive histogram measurements are not required any more. An example for turbo trellis-coded modulation demonstrates the capabilities of the proposed approach     

The slot-coupled hemispherical dielectric resonator antenna with a parasitic patch: applications to the circularly polarized antenna and wide-band antenna

The aperture-coupled hemispherical dielectric resonator antenna (DRA) with a parasitic patch is studied rigorously. Using the Green's function approach, integral equations for the unknown patch and slot currents are formulated and solved using the method of moments. The theory is utilized to design a circularly polarized (CP) DRA and a wide-band linearly polarized (LP) DRA. In the former, the CP frequency and axial ratio (AR) can easily be controlled by the patch location and patch size, respectively, with the impedance matched by varying the slot length and microstrip stub length. It is important that the AR will not be affected when the input impedance is tuned, and the CP design is therefore greatly facilitated. For the wide-band LP antenna, a maximum bandwidth of 22% can be obtained, which is much wider than the previous bandwidth of 7.5% with no parasitic patches. Finally, the frequency-tuning characteristics of the proposed antenna are discussed. Since the parasitic patch can be applied to any DRAs, the method will find applications in practical DRA designs.     

A kinetic study on isothermal crystallization of palm oil by solid fat content measurements

Isothermal crystallization of plam oil was studied by means of differential scanning calorimetry (DSC) as well as by nuclear magnetic resonance spectrometry to monitor its solid fat content (SFC). The temperature of crystallization (Tc) varied from 0 to 30°C, depending on the method used. The plot of %SFC vs. time at 25°C was sigmoidal in shape. However, at lower temperatures, two consecutive curves were clearly visible. Results from DSC experiments showed the following interesting features. At each Tc, the crystals produced were of different compositions. From 0 to 8°C, the thermogram showed three peaks, with the first two peaks (I and II) sharp, and the third (III) rather broad. At elevated temperatures up to 20°C, peak II disappeared totally while peak III tended to shift toward peak I. Above 20°C, both peaks shifted downward to longer times. Peak I continued to be broadened, and then suddenly disappeared at Tc above 24°C. The melting thermograms of the crystals obtained above and below this cut-off point were distinctly different. Kinetic studies on isothermal crystallization based on the data of SFC measurements showed that the data fit well into the Avrami-Erofeev equation with n=3 over the first 70% of the crystallization.     

Motivated attention and prepulse inhibition of startle in rats: Using conditioned reinforcers as prepulses.

In humans, prepulse inhibition (PPI) of startle is greater during attended prestimuli than it is during ignored prestimuli, whereas in rats, most work has focused on passive PPI, which does not require attention. In the work described in this article, researchers developed a paradigm to assess attentional modification of PPI in rats using motivationally salient prepulses. Water-deprived rats were either conditioned to attend to a conditioned stimulus (CS; 1-s, 7-dB increase in white noise) paired with water (CS+ group), or they received uncorrelated presentations of white noise and water (CSo group). After 10 conditioning sessions, startle probes (50 ms, 115 dB) were introduced, with the CS serving as a continuous prepulse. Three experiments examined PPI across a range of prepulse intensities (4-10 dB) and stimulus onset asynchronies (SOAs; 30-960 ms). PPI was consistently reduced in the CS+ group, particularly with a 10-dB prepulse and a 60-ms SOA. Thus, PPI in rats differed between attended and ignored prestimuli, but the effect was reversed in the results of research with humans. A fourth study eliminated the group difference by reversing the CS-water contingency. Methodological and motivational hypotheses regarding the current findings are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Minimizing total weighted completion time when scheduling orders in a flexible environment with uniform machines

We consider the scheduling of orders in an environment with m uniform machines in parallel. Each order requests certain amounts of k different product types. Each product type can be produced by any one of the m machines. No setup is required if a machine switches over from one product type to another. Different product types intended for the same order can be produced at the same time (concurrently) on different machines. Each order is released at time zero and has a positive weight. Preemptions are allowed. The completion time of an order is the finish time of the product type that is completed last for that order. The objective is to minimize the total weighted completion time. We propose heuristics for the non-preemptive as well as the preemptive case and obtain worst case bounds that are a function of the number of machines as well as the differences in the speeds of the machines. Even though the worst-case bounds we showed for the two heuristics are not very tight, our experimental results show that they yield solutions that are very close to optimal.