Investigations of ductile damage during the process chains of toothed functional components manufactured by sheet-bulk metal forming

Sheet-bulk metal forming processes combine conventional sheet forming processes with bulk forming of sheet semi-finished parts. In these processes the sheets undergo complex forming histories. Due to in- and out-of-plane material flow and large accumulated plastic strains, the conventional failure prediction methods for sheet metal forming such as forming limit curve fall short. As a remedy, damage models can be applied to model damage evolution during those processes. In this study, damage evolution during the production of two different toothed components from DC04 steel is investigated. In both setups, a deep drawn cup is upset to form a circumferential gearing. However, the two final products have different dimensions and forming histories. Due to combined deep drawing and upsetting processes, the material flow on the cup walls is three-dimensional and non-proportional. In this study, the numerical and experimental investigations for those parts are presented and compared. Damage evolution in the process chains is simulated with a Lemaitre damage criterion. Microstructural analysis by scanning electron microscopy is performed in the regions with high mechanical loading. It is observed that the evolution of voids in terms of void volume fraction is strongly dependent on the deformation path. The comparison of simulation results with microstructural data shows that the void volume fraction decreases in the upsetting stage after an initial increase in the drawing stage. Moreover, the concurrent numerical and microstructural analysis provides evidence that the void volume fraction decreases during compression in sheet-bulk metal forming.     

Processing and characterization of nanostructured Cu-carbon nanotube composites

Carbon nanotube (CNT) reinforced nanostructured Cu matrix composite with a grain size less than 25 nm has been successfully fabricated via a combination of ball milling and high-pressure torsion. CNTs were found to be homogeneously dispersed into the metal matrix, leading to grain refinement with a narrow grain size distribution and significant increase in hardness.     

The Effect of Gradual Fluorination on the Properties of FnZnPc Thin Films and FnZnPc/C60 Bilayer Photovoltaic Cells

Motivated by the possibility of modifying energy levels of a molecule without substantially changing its band gap, the impact of gradual fluorination on the optical and structural properties of zinc phthalocyanine (F_nZnPc) thin films and the electronic characteristics of F_nZnPc/C₆₀ (n = 0, 4, 8, 16) bilayer cells is investigated. UV–vis measurements reveal similar Q‐ and B‐band absorption of F_nZnPc thin films with n = 0, 4, 8, whereas for F₁₆ZnPc a different absorption pattern is detected. A correlation between structure and electronic transport is deduced. For F₄ZnPc/C₆₀ cells, the enhanced long range order supports fill factors of 55% and an increase of the short circuit current density by 18%, compared to ZnPc/C₆₀. As a parameter being sensitive to the organic/organic interface energetics, the open circuit voltage is analyzed. An enhancement of this quantity by 27% and 50% is detected for F₄ZnPc‐ and F₈ZnPc‐based devices, respectively, and is attributed to an increase of the quasi‐Fermi level splitting at the donor/acceptor interface. In contrast, for F₁₆ZnPc/C₆₀ a decrease of the open circuit voltage is observed. Complementary photoelectron spectroscopy, external quantum efficiency, and photoluminescence measurements reveal a different working principle, which is ascribed to the particular energy level alignment at the interface of the photoactive materials.     

Multicriteria optimization as enabler for Sustainable Ceramic Matrix Composites

Over the past 40 years, development of Ceramic Matrix Composites (CMCs) has focused mainly on the improvement of material performance and optimization of cost-efficient production routes. Recently, more fields of application have opened up for CMCs, in which environmental impacts are relevant. These impacts have barely been investigated so far but receive growing interest due to increasing awareness of the environmental consequences. Our innovative approach frames material properties in relation to environmental impacts (e.g., global warming potential in CO₂ emission) by varying process parameters to balance optimum performance against environmental considerations. First, the process of wet filament winding has been investigated up to the Carbon Fiber Reinforced Plastic (CFRP) state by changing both the curing and tempering temperatures. During the production of CFRP plates, mass and energy flows were tracked in each step. Three point-bending and interlaminar shear tests have been performed on the resulting samples to identify basic mechanical properties. The environmental impacts are determined by a cradle-to-gate Life Cycle Assessment (LCA), using the software SimaPro. The resulting tradeoffs between mechanical properties and environmental impacts show nonlinear behavior, thus revealing optimum points above which improved mechanical properties are associated with significantly higher CO₂ emissions.     

Microstructure of the HMX‐Based PBX KS32 after Mechanical Loading

Non‐destructive X‐ray diffraction techniques were applied in order to monitor the influence of mechanical and shock‐loading on the microstructure of the plastic‐bonded high explosive KS32. The investigations uncovered damage to embedded coarse HMX crystals and to the binder system HTPB‐IPDI. Damage to the crystals occurred already during the kneading process in terms of deformation twinning. On higher loading between 400 MPa (static) and 480 MPa (dynamic) also crystal fracture was observed. The change in the binder structure was found after both static and dynamic loading, but not in the cured, differently kneaded samples. Moreover, the change in binder structure after dynamic loading was verified by dynamic mechanical analysis, and interpreted as a partial damage of the binder rubber shell around the explosive particles. The results are compared to literature data from imaging techniques.     

Efficient Engineering and Production Concepts for Products in Regulated Environments – Dream or Nightmare?

Manufacturing of chemical‐pharmaceutical products is moving increasingly fast on a global scale. Therefore, developing and starting up production facilities fast, with high quality, and at reasonable costs has become extremely challenging. Engineering concepts like modularization, standardization and simultaneous/parallel engineering are discussed as methods for speeding up process design and filing for regulatory approval. Transfer from batch to continuous operation mode of production is pointed out as the key‐issue in such strategies.