Intra- and interspecific mineral composition variability of commercial instant coffees and coffee substitutes: Contribution to mineral intake

The present paper reports the amount and estimated daily mineral intake of nine elements (Ca, Mg, K, Na, P, Fe, Mn, Cr and Ni) in commercial instant coffees and coffee substitutes (n = 49). Elements were quantified by high-resolution continuum source flame (HR-CS-FAAS) and graphite furnace (HR-CS-GFAAS) atomic absorption spectrometry, while phosphorous was evaluated by a standard vanadomolybdophosphoric acid colorimetric method.Instant coffees and coffee substitutes are rich in K, Mg and P (>100 mg/100 g dw), contain Na, Ca and Fe in moderate amounts (>1 mg/100 g), and trace levels of Cr and Ni. Among the samples analysed, plain instant coffees are richer in minerals (p < 0.001), except for Na and Cr. Blends of coffee substitutes (barley, malt, chicory and rye) with coffee (20–66%) present intermediate amounts, while lower quantities are found in substitutes without coffee, particularly in barley.From a nutritional point of view the results indicate that the mean ingestion of two instant beverages per day (total of 4 g instant powder), either with or without coffee, cannot be regarded as important sources of minerals to the human diet, although providing a supplementation of some minerals, particularly Mg and Mn in instant coffees. Additionally, and for authentication purposes, the correlations observed between some elements and the coffee percentage in the blends, with particular significance for Mg amounts, provides a potential tool for the estimation of coffee in substitute blends.     

A methodology for screening of microalgae as a decision making tool for energy and green chemical process applications

The increasing interest for biotechnological use of microalgae demands a methodology for selection of species suitable to support the development of technologies based on the use of such non-conventional renewable raw material, i.e., green industrial applications. The vast and expanding collection of experimental data on both cell growth and biomass composition available in the literature can be used to reduce the cost of the experimental investigations required to support process engineering and optimization. Selecting the appropriate organism requires extracting useful information from such data, a cumbersome task since various multidisciplinary factors must be considered. This paper presents a computer-aided methodology for selecting appropriate algal species given an energy or green chemical process application employing microalgae as a renewable raw material. The approach is “system oriented”, based on biomass composition and chemical processing of the biomass downstream of the CO₂ biofixation and harvesting operations. Quantitative performance results are supported by professional process simulation. Besides comparison of a set of species performances, the proposed methodology also allows the discrimination among distinct algal compositions resulting from different growth conditions for a given species. Furthermore, three categories of screening metrics are proposed to be maximized by the decision making procedure in order to elicit the relevant information. To demonstrate the potential of the proposed methodology, a databank of both biochemical and elemental compositions of microalgal biomass was used in three green applications: Assessment of biomass heating value; production of syngas by gasification of the biomass; and production of Bio-H₂. Within the accuracy of the databank employed to illustrate the procedure, the methodology selected Botryococcus braunii and Isochrysis galbana as potential promising candidates, for the three examined applications.     

In situ injection of THF to trigger gas hydrate crystallization: Application to the evaluation of a kinetic hydrate promoter

This paper investigates an original method to efficiently trigger gas hydrate crystallization. This method consists of an in situ injection of a small amount of THF into an aqueous phase in contact with a gas-hydrate-former phase at pressure and temperature conditions inside the hydrate metastable zone. In the presence of a CO₂–CH₄ gas mixture, our results show that the THF injection induces immediate crystallization of a first hydrate containing THF. This triggers the formation of the CO₂–CH₄ binary hydrate as proven by the pressure and temperature reached at equilibrium. This experimental method, which “cancels out” the stochasticity of the hydrate crystallization, was used to evaluate the effect of the anionic surfactant SDS at different concentrations, on the formation kinetics of the CO₂–CH₄ hydrate. The results are discussed and compared with those published in a recent article (Ricaurte et al., 2013), where THF was not injected but present in the aqueous phase from the beginning and at much higher concentrations.     

A review of manufacturing flexibility: systematising the concept

The present work is an attempt to contribute to the conceptual systematisation of the manufacturing flexibility types by synthesising the vast literature available after a systematic review. We classified the papers in two perspectives (hierarchical and strategic), and engaged in a systematic process of standardisation of the definitions and names of various flexibility types leading to a better understanding of them. This process allowed us to clearly show: (a) the existence of a broader consensus in the field than expected; (b) that problems are limited to concrete aspects related to the level of analysis or the scope of certain flexibility types; (c) the possibility of a theoretical integration between the two perspectives which would permit a standardisation of the names and definitions for the flexibility types which make up the manufacturing flexibility construct.     

Solid lubricant behavior of MoS2 and WSe2-based nanocomposite coatings

Abstract

Tribological coatings made of MoS₂ and WSe₂ phases and their corresponding combinations with tungsten carbide (WC) were prepared by non-reactive magnetron sputtering of individual targets of similar composition. A comparative tribological analysis of these multiphase coatings was done in both ambient air (30–40% relative humidity, RH) and dry nitrogen (RH<7%) environments using the same tribometer and testing conditions. A nanostructural study using advanced transmission electron microscopy of the initial coatings and examination of the counterfaces after the friction test using different analytical tools helped to elucidate what governs the tribological behavior for each type of environment. This allowed conclusions to be made about the influence of the coating microstructure and composition on the tribological response. The best performance obtained with a WSe_x film (specific wear rate of 2 × 10^?8 mm³ N^–1m^–1 and a friction coefficient of 0.03–0.05) was compared with that of the well-established MoS₂ lubricant material.     

Separation of Acylglycerides Obtained by Enzymatic Esterification Using Solvent Extraction

New avenues to add value to glycerol are currently being explored. One of them is the synthesis of structured lipids through glycerol esterification. In this work we have analyzed the recovery and purification of dicaprin obtained by esterification of glycerol with capric acid (C) in heptane, mediated by Lipozyme RM IM. This is an intermediate step to obtain lipids MLM. In the first stage, the diglyceride synthesis MGM (being G a central HC–OH) was carried out. When M = C, the diglyceride is CGC. Recovery of the diglyceride CGC is required to carry out the esterification of the sn-2 position with palmitic acid (P), thus obtaining the triglyceride CPC. Different solvents were evaluated using Ecofac 1.0 (a molecular design software solvent) through a theoretical approach to explore the best solvents for the acylglycerides separation. Then, the performance of the selected solvents to separate dicaprin from mono and tricaprin was experimentally studied in a liquid–liquid extraction process. Previously, the remaining fatty acid had been neutralized. With liquid–liquid extraction in three simple steps, using ethanol/water, 94 % of the dicaprin obtained by enzymatic esterification was recovered with a purity of 89 % (wt%). It was also possible to obtain dicaprin with a purity of 97 % but with a yield of 56 %.     

On extremal dependence: some contributions

The usual coefficients of tail dependence are based on exceedances of high values. These extremal events are useful and widely used in literature but an adverse situation may also occur with the upcrossing of a high level. In this context we define upcrossings-tail dependence coefficients and analyze all types of dependence coming out. We will prove that these coefficients are related to multivariate tail dependence coefficients already known in literature. We shall see that the upcrossings-tail dependence coefficients have the interesting feature of congregating both ??temporal?? and ??spatial?? dependence. The coefficients of tail dependence can also be applied to stationary sequences and hence measure the tail dependence in time. Results concerning connections with the extremal index and the upcrossings index as well as with local dependence conditions will be stated. Several illustrative examples will be exploited and a small note on inference will be given by presenting estimators derived from the stated results and respective properties.     

Non-Intensive Care Unit Acquired Pneumonia: A New Clinical Entity?

Hospital-acquired pneumonia (HAP) is a frequent cause of nosocomial infections, responsible for great morbidity and mortality worldwide. The majority of studies on HAP have been conducted in patients hospitalized in the intensive care unit (ICU), as mechanical ventilation represents a major risk factor for nosocomial pneumonia and specifically for ventilator-associated pneumonia. However, epidemiological data seem to be different between patients acquiring HAP in the ICU vs. general wards, suggesting the importance of identifying non ICU-acquired pneumonia (NIAP) as a clinical distinct entity in terms of both etiology and management. Early detection of NIAP, along with an individualized management, is needed to reduce antibiotic use and side effects, bacterial resistance and mortality. The present article reviews the pathophysiology, diagnosis, treatment and prevention of NIAP.