Friction-induced ultra-fine and nanocrystalline structures on metal surfaces in dry sliding

Sliding friction tests of pin-on-disc type were carried out for carbon steel, pure iron and pure copper, and the microstructure and hardness near the sliding surfaces were investigated in detail. It was found that patchy transfer layers with ultra-fine (<200 nm) structures were produced on the disc surfaces. Nanocrystalline grains of 30–50 nm were identified for carbon steel, and submicron sized grains of 100–150 nm were observed in pure copper. The thicknesses of the ultra-fine structures were in the range of 10–50 μm, depending on the specimen material, sliding speed and applied load. The hardness near the sliding surface of pure iron was increased compared with the matrix. It was suggested that the hardening was due to the very fine structure formed by severe plastic deformation, but not due to phase transformation caused by thermal effects.     

A method to modify coordinates of detectors in positron emission tomography systems

A new method to modify coordinates of detectors in any positron emission tomography (PET) system using a radioactive point source is developed. This method is based on selecting a centered detector in each detector block of PET and measuring coincidence counts between the two centered detectors in opposite detector blocks to find the coordinates of their LOR (Line of Response). Due to slight misalignment of detector positions, measured LORs may not intersect at a single point. Based on the proposed method, the coordinates of detectors can be measured with very high accuracy and the coordinate of the center of the gantry (which is normally the same as the center of field of view) can be defined correctly. The results of the application of our method to a small animal PET system (FinePET), which was recently developed at Tohoku University, Japan, are shown here. The method is expected to contribute to the design and development of PET systems which can realize a very high spatial resolution of less than 1 mm FWHM.     

Kinetics of CO2 reforming of methane by catalytically activated metallic foam absorber for solar receiver-reactors

Ni–Cr–Al metallic foam absorber with high porosity was catalytically activated using a Ru/γ-Al₂O₃ catalyst, and was subsequently tested with respect to CO₂ reforming of methane in a small-scale volumetric receiver-reactor by using a sun-simulator. A chemical storage efficiency of 37% was obtained for a mean light flux of 325 kW m⁻². Furthermore, the activity and the stability of the metallic foam absorber were compared with those of a SiC foam absorber activated with the same Ru/γ-Al₂O₃ catalyst for 50 h of light irradiation, and it was found that the metallic foam absorber has superior catalytic stability in comparison to the SiC form absorber. In addition, unlike ceramic foams such as SiC, metallic foams feature superior plasticity, which prevents the emergence of cracks caused by mechanical or thermal shock.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

Mass mating method in combination with G418- and aureobasidin A-resistance markers for efficient selection of hybrids from homothallic strains in Saccharomyces cerevisiae

We have developed a mass mating method using the spore suspensions of homothallic yeasts of Saccharomyces cerevisiae in combination with dominant selective drug resistance markers, Tn601(903) against geneticin and AUR1-C against aureobasidin A for the selection of the hybrids. To examine the effectiveness of these markers in the mass mating method, each marker was introduced into a homothallic wine yeast. Using a mixed culture of spore suspensions from the resultant transformants, many hybrids were screened by the drug resistance markers. This method is more practical than the spore-to-spore mating method because it does not require the use of a micromanipulator and many hybrids are obtained at one time. The resultant hybrids could be utilized for industrial brewing because plasmids, which are used to confer resistance markers, are easily eliminated from the hybrids by cultivation in a medium without drugs. We propose that the mass mating method using spore suspensions in combination with dominant selective geneticin- and aureobasidin A-resistance markers is useful for the selection of hybrids from industrial homothallic yeasts.     

An optoelectronic self-oscillatory circuit with an optical fiber delayed feedback and its injection locking technique

An optoelectronic self-oscillatory circuit with a constant time delay and its injection locking have been theoretically and experimentally described. The oscillation circuit incorporates a delayed feedback path by utilizing an optical fiber and is characterized by a differential-difference equation. The oscillation waveform and amplitude have been investigated by computing the equation. It is also shown that a stable frequency locking region exists and expands with an increase in the injection amplitude. By employing a carrier signal, two methods for optoelectronic oscillation, an AM and an FM type, are proposed and have been demonstrated to obtain more stable oscillation.     

Finite element incremental contact analysis with various frictional conditions

The use of contacting components such as gear teeth in mesh and shrink-fitted shafts is very common in engineering practice. This paper deals with the development of a theoretical method which gives a solution for non-linear contact problems with irreversibility resulting from stick-slip phenomenon. The method is based on the finite element method and load incremental theory. The geometrical and the statical boundary conditions on contact surfaces are treated as additional conditions being independent of stiffness equations. As a result, the algorithm of calculation is simplified and only a part of the simultaneous equations related to the contact surfaces is required to be solved instead of the overall stiffness equations at each step. Furthermore, the magnitude of load causing a change in a contact condition of one contact nodepair is taken as a load increment, in analogy with the incremental iterative procedure for elastic-plastic problems. Therefore, the method provides a general and efficient method for analysis and design of such problems. As illustrative examples, the stick-slip behaviour of turbo-alternator end-bells and other problems are discussed. The calculated results show a reasonable agreement with experimental data and other solutions.