粘性条件下含不同导叶数的液力透平水力损失分析

为了研究粘性条件下含不同导叶数的液力透平内水力损失的分布情况,采用CFD方法以3种不同黏度工质对3种不同导叶数的泵作液力透平进行数值计算,分析工质黏度对含不同导叶数的液力透平水力损失分布的影响规律。结果表明:叶轮内的水力损失在透平总水力损失中所占比重超过50%,是透平内的主要水力损失;相同流量与工质下,叶轮内的水力损失随着导叶数的增加而减小,叶轮内的流动受导叶数影响显著,蜗壳、导叶等其他过流部分内的流动受导叶数影响较小;随着工质黏度的增加,相同导叶数透平各过流部分的水力损失基本呈增大趋势;在透平叶轮前添加合适叶片数的导叶能够改善叶轮内流动的状况,减小叶轮内水力损失。     

我国堆场磷石膏工程特性分析

磷石膏堆场的渗流及稳定性分析结果的可靠度取决于磷石膏物理力学参数的准确性,因此开展磷石膏工程特性研究十分必要。根据我国不同磷石膏堆场的试验数据,分别对磷石膏的物理性质、击实特性、渗透特性、固结特性和强度特性进行了分析。结果表明:磷石膏强度、压缩、渗透特性均与其压实程度密切相关,相同压实程度不同堆场磷石膏的物理力学性质相近;磷石膏渗透特性与其晶体形态有关;磷石膏在荷载作用下具有长期蠕变变形特性,磷石膏堆场封场后仍会发生较大沉降;深部磷石膏破坏时的应变大于浅层磷石膏;磷石膏剪切破坏时产生负孔隙水压力,实际工程中可通过测试孔压的变化了解堆场坝体的安全程度。     

咖啡渣活性炭的制备、表征及其对Cr(Ⅵ)的吸附机制研究

以碘吸附值为评价指标，活化时间、活化温度和浸渍比为影响因素，采用响应面法试验设计对磷酸活化法制备咖啡渣活性炭的工艺条件进行优化，并通过静态吸附试验研究了不同吸附时间、溶液pH值和吸附温度条件下，活性炭对水溶液中Cr（Ⅵ）吸附性能的影响，最后利用Langmuir、Freundlich吸附等温方程、准一级动力学方程、准二级动力学方程和颗粒内部扩散方程进行拟合。试验结果表明，制备咖啡渣活性炭的最佳工艺条件为活化时间1 h、活化温度498℃、浸渍比1.72；在此条件下活性炭得率为30.4%，碘吸附值为（799±16）mg/g，比表面积为1 006 m²/g，孔容为0.779 cm³/g、微孔孔容为0.051 cm³/g、平均孔径为3.088 nm。较低pH值和较高温度能够促进活性炭对Cr（Ⅵ）的吸附；Langmuir等温方程能够更好地描述活性炭对Cr（Ⅵ）的吸附效果；活性炭对Cr（Ⅵ）的吸附分3个阶段：快速吸附阶段、慢速吸附阶段和吸附平衡阶段，10 min内可完成吸附总量的79%，360 min内达到吸附平衡，该吸附过程符合准二级吸附动力学方程。分析表明咖啡渣活性炭对Cr（Ⅵ）的吸附主要为单分子层的化学吸附。     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。     

Novel thermal-sensitive properties of NBT-BZT composite ceramics for high-temperature NTC thermistors

We found for the first time that (1 − x) Na_0.5Bi_0.5TiO₃-xBiZn_0.5Ti_0.5O₃ (NBT–BZT) composite ceramics showed negative temperature coefficient (NTC) at a high temperature. The NBT–BZT nanopowders were successfully prepared by Pechini method. Their ceramics were sintered at 1100°C. The NBT–BZT ceramic exhibited a good linear relationship between logarithm of electrical resistivity (Inρ) and reciprocal of absolute temperature (1000/T) at 250°C–1050°C. The obtained ρ₆₀₀, ρ₉₀₀, and B_600/900 constants of the NBT–ZBT NTC thermistors are approximately 5.92 × 10⁶ to 3.01 × 10⁴ Ω cm, 7.03 × 10³ to 7.60 × 10² Ω cm and 2.3 × 10⁴-1.3 × 10⁴ K, respectively. The electrical characteristics can be tuned to the desired value by changing the Na_0.5Bi_0.5TiO₃ content in the compound. The electrical conductivity in these compounds is due to the electron jumps between Ti³⁺ and Ti⁴⁺ and oxygen-ion conductivity. Results demonstrate a tremendous potential of the studied system for perovskite materials with NTC performance.     

影响煤层气开发效果的地质因素再认识

地质特征认识对煤层气开发效果起着重要作用。在资源特征相差不大的情况下,发现煤层气相邻井的产量差异仍较大。排除工程因素后,通过选取8类地质参数,细致比对了保德区块低产井与邻井的参数特征,筛查出其关键因素为煤层微幅构造与顶板封盖条件,其中以微幅构造为主。据此,重新认识并划分出区块新的次生褶皱背斜单元、向斜单元和斜坡单元,获得了不同次生褶皱构造单元的开发特征。结果表明,高、低产井分布与次生褶皱背斜、向斜相关性高达92%。其中:高产井主要分布在次生褶皱背斜变化较缓、呈隆起状的“平台”,且煤层顶板以泥岩、碳质泥岩为主,封盖性较好;低产井主要分布在次生褶皱向斜,同一井台各井开发效果差异表现为从向斜条带轴部—向斜条带内—向斜条带外的煤层气井平均单井产量不断增加,到向斜轴部的距离大于向斜曲率半径73.5%的范围为主力产气区,小于向斜曲率半径40.0%范围为产水主力区。这对煤层气新井部署、生产管理、开发调整等,具有一定的指导意义。     

含钒废弃物中钒的回收研究现状及展望

金属钒具备一系列优越性质,在许多领域有着广泛的应用。综述了从含钒钢渣、提钒尾渣、失活催化剂以及钒电池失效电解液等含钒废弃物中回收钒的方法,主要阐述了各种方法的原理、优缺点及发展趋势,介绍了回收钒的新工艺并指出提钒工艺的未来发展方向。     

Electrocatalytic Reduction of CO2 to Ethylene by Molecular Cu‐Complex Immobilized on Graphitized Mesoporous Carbon

The electrochemical reduction of carbon dioxide (CO₂) to hydrocarbons is a challenging task because of the issues in controlling the efficiency and selectivity of the products. Among the various transition metals, copper has attracted attention as it yields more reduced and C2 products even while using mononuclear copper center as catalysts. In addition, it is found that reversible formation of copper nanoparticle acts as the real catalytically active site for the conversion of CO₂ to reduced products. Here, it is demonstrated that the dinuclear molecular copper complex immobilized over graphitized mesoporous carbon can act as catalysts for the conversion of CO₂ to hydrocarbons (methane and ethylene) up to 60%. Interestingly, high selectivity toward C2 product (40% faradaic efficiency) is achieved by a molecular complex based hybrid material from CO₂ in 0.1 m KCl. In addition, the role of local pH, porous structure, and carbon support in limiting the mass transport to achieve the highly reduced products is demonstrated. Although the spectroscopic analysis of the catalysts exhibits molecular nature of the complex after 2 h bulk electrolysis, morphological study reveals that the newly generated copper cluster is the real active site during the catalytic reactions.     

Within-class multimodal classification

Multimedia Tools and Applications - In many real-world classification problems there exist multiple subclasses (or clusters) within a class; in other words, the underlying data distribution is...