Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at     

Expectations about counseling in Yucatán, Mexico: Toward a "Mexican psychology."

Conducted a study of client expectations of psychological services in Yucatán, Mexico, under the sponsorship of a grant from the Organization of American States. The Expectations about Counseling–Brief form (EAC-B) questionnaire was translated and administered to 488 subjects across age, sex, and experience with psychological services. Subsequent analyses supported the reliability and robustness of the Spanish EAC-B, with factor structure similar to the EAC-B in English. Some relation was found among age, sex, prior counseling experience, and expectations about counseling. Implications of these data for future research and comparison with U.S. subjects are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Synthesis of sliding-mode controllers for nonlinear systems via extended linearization

In this article, a general synthesis method is proposed for the design of discontinuous feedback strategies leading to asymptotically stabilizing sliding regimes. The method is applicable to the class of nonlinear dynamical systems possessing constant equilibrium points. A family of nonlinear stabilizing sliding manifolds, parametrized by generic desired equilibrium point, is specified on the basis of the extended linearization approach. Some examples including simulations are presented for illustrative purposes. Editor: S. Zak     

Antimutagenic activity of phenolic compounds, oligosaccharides and quinolizidinic alkaloids from Lupinus campestris seeds.

There are some foods that contain mutagenic or carcinogenic agents, some of which occur naturally and others that may be formed during preparation or cooking. Several foods such as legumes, also contain natural antimutagens and/or anticarcinogens. Lupine is one such legume that contains high amounts of protein (40%) and oils (14%). About 90 species of lupine have been reported throughout Mexico. However, the use of this crop as a source of food has been limited by the presence of antinutritional agents such as phenolic compounds (PC), carbohydrates (CH) and quinolizidinic alkaloids (Qas). It has also been suggested that consuming these compounds can affect human health and may even reduce the risk of disease. The objective of this work was to determine the effect of PC, CH and Qas, isolated and quantified from Lupinus campestris on the mutagenicity of 1-nitropyrene (1-NP) as a model mutagen and we used the Salmonella typhimurium tester strain YG1024 by the Kado microsuspension method. The results indicate that L. campestris seeds have 11 mg (+)catechin equivalent g(-1) seed coat; 120.3 mg g(-1) seeds and 2.13 mg g(-1) seeds of PC, CH and Qas, respectively. 1-NP mutagenicity was inhibited by 86% for PC, 76% for CH and 75% for Qas at concentrations of 200, 512 and 13.6 microg/tube, respectively.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Molecular weight effect on the obtainment of parallel and perpendicular orientation in thermotropic poly(diethylene glycol <Emphasis Type="Italic">p,p′</Emphasis>-bibenzoate)

Summary The effect of molecular weight on the uniaxial orientation process has been analyzed in two samples of thermotropic poly(diethylene glycol p,p′-bibenzoate), evaluating the influence of that parameter on the type of orientation obtained. Several strain rates and deformation temperatures have been tested in order to map out the conditions for obtaining the two different kinds of orientation. The results show that in the lower molecular weight PDEB sample (M_w=31200) it is rather easy to get exclusively perpendicular “anomalous” orientation, with the molecular axes aligned transversely to the stretching direction. However, it is extremely difficult to obtain 100% parallel “normal” orientation. On the contrary, either type of orientation or a mixture of them can be easily developed for the higher molecular weight PDEB sample (M_w=102900).     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry