Initial Deposition of Colloidal Particles on a Rough Nanofiltration Membrane

The initial rate of colloid deposition onto semi‐permeable membranes is largely controlled by the coupled influence of permeation drag and particle‐membrane colloidal interactions. Recent studies show that the particle‐membrane interactions are subject to immense local variations due to the inherent morphological heterogeneity (roughness) of reverse osmosis (RO) and nanofiltration (NF) membranes. This experimental investigation reports the effect of membrane roughness on the initial deposition of polystyrene latex particles on a rough NF membrane during cross flow membrane filtration under different operating pressures and solution chemistries. Atomic force microscopy was used to characterize the roughness of the membrane and observe the structure of particle deposits. At the initial stages of fouling, the AFM images show that more particles preferentially accumulate near the “peaks” than in the “valleys” of the rough NF membrane surface.     

Modification of non‐Newtonian flow behavior of aqueous solution of poly(vinyl alcohol) by conducting polypyrrole prepared by in situ polymerization of pyrrole

The rheological behavior of an aqueous solution of poly(vinyl alcohol) (PVA) and polypyrrole (PPY) dispersions prepared by ferric chloride (FeCl₃)‐catalyzed polymerization of pyrrole was investigated at 12°C using a coaxial rotational viscometer. The results show that the addition of a low dose of FeCl₃ to the PVA solution greatly influences its rheology. The prominent shear‐thickening (dilatant) nature of PVA turns significantly pseudoplastic (shear thinning) in the presence of FeCl₃. Polypyrrole‐loaded PVA was obtained in a stable, optically clear dispersion by in situ polymerization of pyrrole in an aqueous PVA solution (5%) using FeCl₃ as the oxidative catalyst at 12°C. The PPY dispersions in aqueous PVA systems having a low loading of PPY and low Fe⁺³ content retain the dilatant character of an aqueous PVA solution; however, for an aqueous PVA system having a relatively high PPY loading and also a high Fe⁺³ content, prominent pseudoplastic (shear thinning) behavior is exhibited. The odd novel rheological patterns exhibited by a PVA solution in the absence and presence of FeCl₃ and the PVA–PPY dispersions containing FeCl₃ under different sets of conditions are explained on the basis of the complexation of PVA by Fe⁺³ and related ions and also as a consequence of some degree of H‐bonding and chemical grafting between the support polymer PVA and the PPY formed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3737–3741, 2004     

Synthesis and densification of magnesium aluminate spinel: effect of MgO reactivity

Stoichiometric magnesium aluminate spinel was synthesized by reaction sintering of alumina with caustic and sintered magnesia. The volume expansion of 5–7% during MgAl₂O₄ formation was utilized to identify the starting temperature of spinel formation and densification by high temperature dilatometry. The magnesia reactivity was determined by measurement of crystallite size and specific surface area. Caustic magnesia and sintered magnesia behave differently vis-à-vis phase formation and densification of spinel. Densification of stoichiometric Mag-Al spinel was carried out between 1650 and 1750 °C. Attempts were made to correlate the MgO reactivity with microstructure and densification of spinel.     

The effect of temperature and moisture on the rheology of black coal-oil suspensions

Rheological properties of black coal-KC220 oil suspensions have been investigated using a Contraves rheometer over a temperature and coal volume fraction range of 18–200°C and 0.247-0.385, respectively. The suspensions behaved as Newtonian fluids. Variation of viscosity with temperature does not follow any regular trend and peak viscosity values occur in the temperature range of 80–140°C for dry coal and 70–130°C for moist coal, depending upon the concentrations of coal in the suspension. Freshly prepared suspensions of moist coal exhibit viscosity peaks at a temperature lower than that of the corresponding suspension with dry coal. However, when aged, the suspensions of moist coal exhibit very small peak viscosity and follow an Arrhenius type behavior. For both dry and moist coal, the maximum volume fraction, ?_m, continues to decrease with an increase in temperature.     

Recycling of silicone rubber waste: Effect of ground silicone rubber vulcanizate powder on the properties of silicone rubber

The silicone rubber vulcanizate powder (SVP) obtained from silicone rubber by mechanical grinding exists in a highly aggregated state. The particle size distribution of SVP is broad, ranging from 2 µm to 110 µm with an average particle size of 33 µm. X‐ray Photoelectron Spectroscopy (XPS) and Infrared (IR) Spectroscopy studies show that there is no chemical change on the rubber surface following mechanical grinding of the heat‐aged (200°C/10 days) silicone rubber vulcanizate. Addition of SVP in silicone rubber increases the Mooney viscosity, Mooney scorch time, shear viscosity and activation energy for viscous flow. Measurement of curing characteristics reveals that incorporation of SVP into the virgin silicone rubber causes an increase in minimum torque, but marginal decrease in maximum torque and rate constant of curing. However, the activation energy of curing shows an increasing trend with increasing loading of SVP. Expectedly, incorporation of SVP does not alter the glass‐rubber transition and cold crystallization temperatures of silicone rubber, as observed in the dynamic mechanical spectra. It is further observed that on incorporation of even a high loading of SVP (i.e., 60 phr), the tensile and tear strength of the silicone rubber are decreased by only about 20%, and modulus dropped by 15%, while the hardness, tension set and hysteresis loss undergo marginal changes and compression stress‐relaxation is not significantly changed. Atomic Force Microscopy studies reveal that incorporation of SVP into silicone rubber does not cause significant changes in the surface morphology.     

FRP composites based on different types of glass fibers and matrix resins: A comparative study

Flexural properties, impact energy, heat deflection temperature, and resistance to thermal and hydrothermal degradation of composites based on E-glass and N-glass fibers as the reinforcing agents, and epoxy, unsaturated polyester, phenolic, and epoxy-phenolic resin systems as the matrix materials were studied and compared. As a reinforcing agent E-glass fiber is superior to N-glass fiber, particularly with respect to development of flexural strength and modulus, impact strength, and thermal resistance; N-glass fiber, however, imparts to the composites substantially higher resistance to hydrothermal degradation under boiling conditions in different chemical environments. For use of both E-glass and N-glass fibers as reinforcing agents, the general order of resistance to hydrothermal degradation for the composites based on different matrix resins is epoxy > phenolic > unsaturated polyester resin. Incorporation of a low dose of a rubbery polymer, such as styrene butadiene rubber (0.1–0.2%) and liquid polybutadiene (0.5–0.75%), in unsaturated polyester resin as the matrix resin measurably enhances impact energy of the composite. © 1995 John Wiley & Sons, Inc.     

Modeling of time to corrosion-induced cover cracking in reinforced concrete structures

Service life of the concrete structures depends on the protective action provided by the cover concrete against the susceptibility of the reinforcement to the corrosive environment. Depending on the level of the oxidation of metallic iron, corrosion products may have much greater volume than the original iron that gets consumed by the process of corrosion. This volume expansion is mainly responsible for exerting the expansive radial pressure at the steel-concrete interface and development of hoop tensile stresses in the surrounding concrete resulting ultimately in the through cracking of the cover concrete. This cover cracking would indicate the loss of the service life for the corrosion-affected structures. In the present paper, an attempt has been made to develop analytical models for predicting the time to cover cracking by considering the residual strength of the cracked concrete and the stiffness provided by the combination of the reinforcement and expansive corrosion products. The problem is modeled as a boundary value problem wherein the governing equations are expressed in terms of the radial displacement and the analytical solutions are presented considering a simple 2-zone model for the cover concrete viz. cracked or uncracked. The analytical models are then evaluated through their ability to reproduce available experimental trends and subsequently a sensitivity analysis has also been carried out to show the influence of the various variable parameters of the proposed models with reference to the experimental trends.     

Occurrence of wax esters and 1-O-alkyl-2,3-diacylglycerols in goat epididymal sperm plasma membrane

Two unusual lipid classes were detected by thin-layer chromatography in the neutral lipids derived from goat cauda-epididymal sperm plasma membrane. The lipids were identified as wax esters and 1-O-alkyl-2,3-diacylglycerols based on chromatographic properties, identity of their hydrolysis products, and infrared/¹H nuclear magnetic resonance spectral evidence. The membrane containedca. 3 and 5 μg/mg protein of wax esters and alkyldiacylglycerols, respectively. The relative proportions of wax esters and alkyldiacylglycerols in the total neutral lipids were 1.5% and 2.4%, respectively. The lipids contained fatty acids with chain lengths of C₁₄ to C₂₂. The major fatty acids of the wax esters were 14∶0, 16∶0, 16∶1ω7, 18∶0 and 18∶1ω9. The fatty acids in alkyldiacylglycerol were 16∶0, 18∶0, 22∶5ω3 and 22∶6ω3. Alkyldiacylglycerol was particularly rich in docosahexaenoic acid 22∶6ω3) representing 30% of the total fatty acids. The alcohols of wax ester were all saturated with C₂₀–C₂₉ carbon chains. The deacylated products derived from alkyldiacylglycerols were identified as hexadecyl, octadecyl and octadec-9′-enyl glycerol ethers.     

Analysing the patterns of spatial contrast discontinuities in natural images for robust edge detection

Pattern Analysis and Applications - The pattern of spatial contrast discontinuities in natural images has been analysed in the present work, and based on it, a new adaptive model of the...     

Interpenetrating polymer network/functionalized-reduced graphene oxide nanocomposite: As an advanced functional material

In this report, smart polyurethane-polystyrene interpenetrating polymer network (IPN)-based nanocomposites were fabricated using simultaneous polymerization technique with different doses of functionalized reduced graphene oxide (f-RGO). RGO was functionalized with monoglyceride of sunflower oil in the presence of toluene diisocyanate. Successful functionalization of RGO was supported by Fourier-transform infrared spectroscopy, X-Ray diffraction, and transmission electron microscopy analyses. Most interestingly, the fabricated IPN-based nanocomposites showed significant enhancements in mechanical (tensile strength: 165%; elongation at break: 198%; toughness: 340%) and thermal (thermally stable up to 262°C) properties upon incorporation of 1 weight% of f-RGO. Moreover, the fabricated nanocomposites exhibited outstanding chemical resistance, self-cleaning behavior through surface hydrophobicity (static contact angle: 125.6–136.5°), multi-stimuli responsive shape memory effect (100% recovery within 33–44 s by microwave and 265–308 s by sunlight) and thermally actuated artificial muscle-like behavior. Therefore, the studied smart nanocomposites with the aforementioned properties hold significant potential for possible advanced applications.