Examination of the role of oxygen in the photografting of methacrylic acid on a polyethylene film with a mixed solvent consisting of water and organic solvents

The photografting of methacrylic acid (MAA) on a linear low‐density polyethylene film (thickness = 30 μm) under air and nitrogen atmospheres was investigated at 60°C in mixed solvents consisting of water and an organic solvent, with xanthone as a photoinitiator. The organic solvents used were acetone, methanol, tetrahydrofuran, and dioxane. A maximum percentage of grafting occurred at a certain concentration of the organic solvent in the mixed solvent. This was observed for the systems under both air and nitrogen. The grafting reaction under air exhibited an induction period, but the rate of grafting after the period was greater than that under nitrogen. The formation of poly(ethylene peroxide)s by photoirradiation seemed to be a factor for the accelerated photografting under air. On the basis of attenuated total reflection infrared spectroscopy and scanning electron microscopy of the grafted film, the MAA‐grafted chains of the sample prepared under air tended to penetrate more deeply inside the film than those of the sample prepared under nitrogen. The resulting grafted films exhibited a pH‐responsive character: the grafted films shrank in an acidic medium but swelled in alkaline medium. This was evaluated from measurements of dimensional changes in the grafted films. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 992–998, 2003     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

ESD phenomena in GMR heads in the manufacturing process of HDD and GMR heads

It is well known that giant magnetoresistive (GMR) heads used for hard disk drives (HDD) are very sensitive to electrostatic discharge (ESD). In this paper, we describe a method of categorizing ESD damage modes from a standpoint of magnetic influences on the heads as observed by quasi-static test (QST) characteristics as well as electromagnetic characteristics like off-track profiles. In addition, we report an example of GMR stack interlayer diffusion which is one type of hard ESD damage. We also present an example of ESD damage that happened in an actual production process and its preventive measures as guidelines.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Thiamine pyrophosphatase activity in the Golgi apparatus of calcitonin-treated osteoclasts.

The thiamine pyrophosphatase (TPPase) activity described by Novikoff and Goldfisher was examined in osteoclasts affected by calcitonin in order to elucidate whether the morphological and functional changes of the osteoclasts have an influence over the secretion function of their Golgi apparatus. The Golgi apparatus of osteoclasts of which the ruffled border had disappeared and bone resorption discontinued as the result of treatment with calcitonin showed a slight TPPase activity. The reaction products of the enzyme in these inactive osteoclasts were distinctly fewer than that of control osteoclasts, which were not affected by calcitonin. From these results, it is suggested that there may be a connection between the morphological and functional changes of osteoclasts and the secretion function of the Golgi apparatus.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Polarimetric Characteristics of sea ice in the sea of Okhotsk observed by airborne L-band SAR

The Phased-Array L-Band SAR (PALSAR) aboard the Advanced Land Observing Satellite (ALOS) is capable of globally acquiring fully polarimetric data. In order to confirm the ability of L-band polarimetric synthetic aperture radar (SAR) to investigate sea ice before the ALOS launch, we conducted a field experiment using an airborne Polarimetric and Interferometric SAR (Pi-SAR) in the Sea of Okhotsk in 1999. This paper presents the analyzed results of data acquired in that experiment. The extracted polarimetric parameters of several ice types suggested that polarimetric coherences and phase differences between right-right (RR) and left-left (LL) are good candidates for discriminating ice types. The polarimetric anisotropy as well as the beta angle of the first eigenvector calculated in the polarimetric decomposition procedure are alternative parameters that are sensitive to ice type differences. Due to the low depolarization characteristics of open water, it could be discriminated from sea ice by scattering entropy in all incidence angle ranges. From the relation between ice thickness and the polarimetric parameters, we found that backscattering coefficients and vertical (VV) to horizontal (HH) backscattering ratio are highly correlated with ice thickness. Since the ratio is sensitive to ice surface dielectric constants, a simple simulation using the integral equation method surface model was conducted by using the physical parameters of typical sea ice. A two-dimensional ice thickness map was derived from an empirical relation between the VV-to-HH backscattering ratio and ice thickness.     

The cause of the uneven carbonization process in wet coal charging in coke oven chamber

In the case of the wet coal charging process in coke oven chamber, it is known that the coking process is uneven and a local carbonization delay occurs. The reason was investigated through a laboratory-scale experiment and a quantitative estimation. A partial carbonization test in a test coke oven replicated the uneven plastic layer and local carbonization delay. It was revealed that most of the gas generated in the uncarbonized coal layer results from the evaporation of condensed water and that steam can break through the plastic layer in a test coke oven. Moreover, the order estimation implied that steam that generates in the uncarbonized coal layer and breaks through the plastic layer has sufficient heat capacity to cool the heating wall and delay the carbonization. It was also shown that the steam pressure peak measured in a commercial coke oven is much lower than the estimated steam pressure in this study assuming steam not breaking through the plastic layer. The above-mentioned results and quantitative investigation strongly support the ‘steam breaking through the plastic layer’ theory proposed by Dr. Rohde that an uneven carbonization process is caused by vaporized coal moisture breaking through the plastic layer at definite, unforeseeable points, which results in cooling of the wall by the steam flow.