Comments on `A Bayes sensitivity analysis when using the betadistribution as a prior'

The commenter makes several critical comments concerning the above-named work of B.S. Duran and J.M. Booker (see ibid., vol.37, p.239-47, June 1988). Duran and Booker present a detailed reply, pointing out, among other things, that the commenter is assuming a much more well-defined problem than theirs     

Adjusting software failure rates that are estimated from test data

Software test environments are often different from field environments. Using test data exclusively to estimate a field failure rate will not usually give a very accurate estimate. In this paper, we extend an empirical calibration methodology for adjusting the failure rate estimate obtained from analysing test data. In addition to scaling the estimated failure rate of a fault, we propose scaling the estimated number of residual faults as well. We also derive likelihood ratio tests to formally determine (from previous releases of the software) if test, and field environments are significantly different. We illustrate our new results with two telecommunications case studies. The combination of the likelihood ratio test, and the calibration methodology offers a practical way to extend the application of software reliability growth models to less formal test environments.     

A Review on Metal‐Free Doped Carbon Materials Used as Oxygen Reduction Catalysts in Solid Electrolyte Proton Exchange Fuel Cells

Within the last decade, metal‐free heteroatom doped carbon nanomaterials have gained attention as effective electrocatalysts for the oxygen reduction reaction (ORR) in many electrochemical systems. Since then, reports have stated that the ORR catalytic activity, onset potential, and H₂O production selectivity of these materials is similar to that of platinum‐based catalysts. These statements rely on cyclic voltammetry (CV) and rotating disc electrode (RDE) measurements in liquid alkaline electrolyte. However, fuel cell researchers aim to replace the costly platinum catalysts in the more prominent acidic solid electrolyte proton exchange fuel cell (PEFC). In this respect, there are only a few reports of unpromising activity, stability, and H₂O production selectivity. In addition, only few reports have been presented on the implementation of such materials in cathode catalyst layers of actual PEFC devices. This mini‐review aims to summarize and evaluate results of these reports. Material synthesis, cell power, open circuit voltage, stability properties, and proposed active sites are reviewed. To date, the highest reported PEFC power densities with guaranteed metal‐free heteroatom doped carbon cathode catalysts have reached up to 321 mW cm⁻²; which although a promising value is substantially short of values obtained for platinum based catalysts.     

Electro ultrasonic remediation of polycyclic aromatic hydrocarbons from contaminated soil

The polycyclic aromatic hydrocarbons (PAHs) with high molecular mass are renown for their high persistence in the soil, hydrophobic and toxicity. Remediation of these pollutants is still an unsolved task and needs more researches to be performed. The coupling of electrokinetics (EK) with ultrasonic energy (US) has advantages on desorbing and migrating PAHs from contaminated soil. US and EK work together to destroy PAHs. The objective of this study was to treat PAHs contaminated soil by using EK and ultrasonication. The contaminated oil contained about 100 mg kg⁻¹ chrysene. Experiments with US, EK and combined EK and ultrasound were conducted in reactors and pans with and without iron anodes. Results indicated that the removal was more effective with lower concentrations of chrysene. The average removal was better in experiment with combined EK and ultrasound using iron anode. This might be due to increase in electroconductivity by iron ions.     

Determination of the heat transfer coefficient from short‐shots studies and precise simulation of microinjection molding

The filling process of a micro‐cavity was analyzed by modeling the compressible filling stage by using pressure‐dependent viscosity and adjusted heat transfer coefficients. Experimental filling studies were carried out at the same time on an accurately controlled microinjection molding machine. On the basis of the relationship between the injection pressure and the filling degree, essential factors for the quality of the simulation can be identified. It can be shown that the flow behavior of the melt in a micro‐cavity with a high aspect ratio is extremely dependent on the melt compressibility in the injection cylinder. This phenomenon needs to be considered in the simulation to predict an accurate flow rate. The heat transfer coefficient between the melt and the mold wall that was determined by the reverse engineering varies significantly even during the filling stage. With increasing injection speed and increasing cavity thickness, the heat transfer coefficient decreases. It is believed that the level of the cavity pressure is responsible for the resulting heat transfer between the polymer and the mold. A pressure‐dependent model for the heat transfer coefficient would be able to significantly improve the quality of the process simulation. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Comparison of particle-phase polycyclic aromatic hydrocarbons and their variability causes in the ambient air in Ho Chi Minh City, Vietnam and in Osaka, Japan, during 2005-2006

A comparative study of polycyclic aromatic hydrocarbons (PAHs) associated with particulate matter (TSP) in the ambient air in an urban area in Ho Chi Minh City, Vietnam and in Osaka, Japan was carried out from 2005 to 2006. The objective of this study was to investigate the environmental levels, emission sources, seasonal variations and health risk of eleven PAHs in the two cities, especially Ho Chi Minh City where air pollution is becoming a serious concern. The results showed that the concentrations of TSP and total PAHs were significantly higher in Ho Chi Minh City than levels in Osaka. The concentrations of 5- and 6-ring PAHs (BeP, BbF, BkF, BaP, BghiP and InP) were much higher in TSP samples in Ho Chi Minh City than in Osaka, accounting for 82% and 51% of total PAHs, respectively. These PAHs are known to be highly carcinogenic and mutagenic in humans. Vehicular emission is suggested as one of the main pollution sources of PAHs in both cities. Motorcycles and gasoline automobiles are suggested as the main emission sources of PAHs in Ho Chi Minh City, whereas diesel automobiles are the primary source in Osaka. Seasonal variations of PAHs were observed in this study; higher concentrations of PAHs were found in the rainy season (May-December) and lower concentrations corresponded to the dry season (February-April) in Ho Chi Minh City, while higher concentrations of PAHs were observed in the winter (November-January) in Osaka. The number of sunshine hours was an important meteorological factor affecting seasonal variations of PAHs in Ho Chi Minh City, while the temperature was a main factor causing the variations of PAHs in Osaka. The high BaP equivalent concentration of 5- and 6-ring PAHs even in the ambient air is an alarming signal for harmfulness to human health and environmental quality in Ho Chi Minh City.     

Hydrogen Generation from CO2 Reforming of Biomass-Derived Methanol on Ni/SiO2 Catalyst

Topics in Catalysis - CO2 reforming of methanol for producing hydrogen was experimentally carried out in a fixed-bed reactor on 10%Ni/SiO2. The 10%Ni/SiO2 was completely reduced during H2...     

Antioxidant Properties of Genistein in a Model Edible Oil System

ABSTRACT:  Antioxidant properties of genistein were tested during the low temperature oxidation of linseed oil. Four linseed oil solutions were prepared: linseed oil, linseed oil containing 2 μmol added genistein/g oil, linseed oil containing 4 μmol added genistein/g oil, and linseed oil containing 200 ppm butylated hydroxyanisole (BHA). Dimethyl sulfoxide (DMSO) (1.7%) was added to all solutions to allow for the solubilization of genistein. Antioxidant activities were analyzed using 2 techniques: (i) the oven stability test carried out at 60 °C with periodic determination of peroxide values (PV); and (ii) oxidation on a heated (60 °C) FTIR-ATR crystal with periodic scanning and collection of infrared spectra. Induction points (IP) for each solution were determined. A strong correlation ( r = 0.91) was noted between the 2 analytical methods used. Three significantly ( P < 0.10) different levels of IP were generally observed. The shortest IP (17 h for PV, 36.9 h for FTIR) was found for the linseed oil. Intermediate IP's were obtained for the 2 μmol added genistein/g oil (32.4 h for PV, 43.5 h for FTIR) and 4 μmol added genistein/g oil (33.9 h for PV, 44.2 h for FTIR) samples. The longest IP (39.9 h for PV, 54.2 h for FTIR) was obtained for the 200 ppm BHA containing solution. Although genestein was not as effective as BHT in retarding oxidation, the results clearly demonstrate that it is able to act as an antioxidant in a bulk oil system.     

Moisture sorption isotherm of fresh lean beef and external beef fat

The moisture sorption isotherm (MSI) of lean beef and fat beef was experimentally determined. The experimental procedure used was that of the COST 90 project with some modifications to accelerate equilibration. The procedure was validated with the standard reference material microcrystalline cellulose. The MSI of the beef at the highest humidity range was obtained by accelerating equilibration with changes of salts, using a low water activity salt for some time. This procedure was reliable for beef samples but not for the fat samples. No significant changes were found for lean beef in the temperature range 5–40 °C. Three models, GAB, Peleg and Lewicki, were used to fit the experimental data. The best fit was obtained with the GAB equation. The fat MSI was determined at 5, 15 and 25 °C and it was best fitted with the Lewicki model.