可持续理念下的风景园林评价体系研究

随着可持续理念在20多年的发展中被广泛接受和认可,城市风景园林的可持续性也受到广泛关注,各国都在探索可持续理念下的城市景观的建设与发展。对不同国家和中国台湾地区现阶段已经建立的可持续风景园林的评价体系,按照定性、定量及综合评价方法的方式进行分类,分别进行阐述与比较,并提出了中国建立可持续风景园林评价体系的建议。     

Pressureless sintering of boron carbide

The effect of small Al addition on pressureless-sintering and mechanical properties of B₄C ceramic was analyzed. Different amounts of aluminium powder, from 0% to 5 wt%, were added to the base material and pressureless-sintering was conducted at 2050 and 2150 °C under argon atmosphere. Microstructure, crystalline phases, density evolution, fracture strength, elastic modulus, hardness and fracture toughness were analyzed and correlated to Al additions and firing temperature. Density and grain size of sintered samples increased significantly with Al load while the effect of sintering temperature was less evident; 94% dense material was obtained by adding 4 wt% Al. Bending strength, hardness and fracture toughness of sintered B₄C samples were shown to increase for Al content up to 4 wt% while further additions resulted in a decrease of the mechanical resistance. Conversely, elastic modulus showed an increase with Al load especially between 1 and 3 wt%.     

Upgrading of LCO by partial hydrogenation of aromatics and ring opening of naphthenes over bi-functional catalysts

Available options to upgrade LCO to diesel fuel are: i) aromatic saturation (ASAT) ii) mild hydrocracking and iii) aromatic saturation followed by selective ring opening (SRO) of naphthenic structures. Although the above mentioned routes lead to significant product quality enhancement, they suffer from several disadvantages. Hydrocracking leads to significant yields in gasoline-range products, ASAT is characterized by a relatively high consumption of hydrogen with only limited improvement of product quality in terms of density and cetane properties, ASAT + SRO route leads to higher improvements of product quality but it requires a very high hydrogen consumption which strongly affects the economics of the process.An alternative upgrading route consists in partial polyaromatic compound saturation and selective opening of both naphthenic and benzo-naphthenic structures to produce less condensed naphthenic structures and alkyl-benzenes respectively. In this case the hydrogen needed to improve product quality at the same level, of cetane properties and density, is lower in comparison with ASAT.This paper reports the results obtained during a research program aimed at upgrading LCO via selective ring opening. The hydroconversion of a low sulfur hydrotreated LCO has been studied over iridium and platinum loaded on different supports. The results of this study indicate that the properties of products heavily depend on the characteristics of the support and the metal used. The data obtained with the Ir/amorphous silica-alumina (MSA) show the possibility to get a clear increase of CN and decrease of density in comparison with the mere aromatic saturation. The practical consequence of this result is the possibility of producing products with CN and density similar to products obtained by complete dearomatization but still containing a significant percentage of aromatic structures so allowing a consistent saving of hydrogen.     

A spectro-microscopic investigation of Fe-Co bimetallic catalysts supported on MgO for the production of thin carbon nanotubes

Fe-Co bimetallic catalysts supported on MgO were studied for the catalytic chemical vapor deposition growth of carbon nanotubes (CNTs). Different wt.% metal loadings were investigated at various deposition temperatures and times. Characterization of the products involved thermal analysis (DTA-TGA), X-ray diffraction, spectroscopy (Raman, UPS, EELS and STS) and microscopy (SEM, TEM and STM) techniques. It was found that the metal content is critical, not only to the yield and the structural quality of the synthesized carbon nanotubes, but it can be also used to tune the desired type of synthesized nanotubes. Lower (2 wt.%) loadings of Fe-Co catalysts favor the formation of single- and/or double-wall CNTs for deposition time and temperature 30 min and 800 °C, respectively. Thermal analysis and Raman measurements showed that these thin CNTs were synthesized at high amounts (CNT-per-catalyst wt.% of more than 100%), exhibiting high graphitization degree with only traces of by-products (mainly amorphous carbon) among them. Microscopy results revealed the formation of CNTs bundles, consisting of individual nanotubes with less than 2 nm outer diameter, while additional energy loss measurements pointed out that the deposited CNTs are mainly single wall. Higher (10 wt.%) Fe-Co loadings resulted to the formation of multi-wall CNTs.     

In vitro fermentation characteristics of diets with different forage/concentrate ratios: comparison of rumen and faecal inocula

BACKGROUND: The aim of this trial was to evaluate the replacement of rumen fluid with faeces as inoculum in studying the in vitro fermentation characteristics of diets for ruminants using the in vitro gas production technique. Six iso‐protein diets with different forage/concentrate ratios were incubated with rumen fluid (RI) or faeces (FI) collected from sheep. RESULTS: Most of the fermentation parameters were influenced by diet and inoculum (P < 0.01). With both inocula, organic matter degradability (dOM), cumulative gas production (OMCV) and maximum fermentation rate (R_max) increased as the amount of concentrate in the diet increased. R_max was lower with FI vs RI (P < 0.01); dOM was higher with FI vs RI and the diet × inoculum interaction was significant. As expected, with both inocula, R_max increased as the neutral detergent fibre content of the diet decreased. Significant correlations were obtained using both inocula between OMCV/dOM and gas/volatile fatty acid (VFA), while the correlation VFA/dOM was significant only with FI. The microbial biomass yield calculated by stoichiometric analysis for all diets was higher with FI vs RI. With FI the organic matter used for microbial growth showed an overall decreasing trend as the amount of concentrate in the diet increased. CONCLUSION: The results indicate that both faeces and rumen fluid from sheep have the potential to be used as inoculum for the in vitro gas production technique. Copyright © 2011 Society of Chemical Industry