Luminescence from praseodymium doped AlN thin films deposited by RF magnetron sputtering and the effect of material structure and thermal annealing on the luminescence

Thin films of Praseodymium doped AlN are deposited on silicon (111) substrates at 77 K and 950 K by rf magnetron sputtering method. About 500–1000 nm thick films are grown at 100–200 watts RF power and 5–8 mTorr nitrogen, using a metal target of Al with Pr. X-rays diffraction results show that films deposited at 77 K are amorphous and those deposited at 950 K are crystalline. Cathodoluminescence studies are performed at room temperature and luminescence peaks are observed in a wide range from ultraviolet to infrared region. The most intense peak is obtained in green at 526 nm from amorphous films as a result from ³P₁→³H₅ transition. In crystalline films the intense peak was obtain in red at 648 nm as a result from ³P₀→³F₂ transition. Films are thermally activated at 1300 K for half an hour in a nitrogen atmosphere. Thermal activation enhances the intensity of luminescence. Two peaks at 488 nm and 505 nm merged after thermal activation, giving rise to a single peak at 495 nm.     

碾压混凝土抗裂性能的几个影响因素研究

影响碾压混凝土抗裂性能的因素很多，本文主要从水泥矿物成分、石粉含量、掺和料（氧化镁等）、骨料特性（弹性模量）及砂率等方面影响因素开展试验研究，分析各因素对碾压混凝土抗裂性能的影响效果。试验结果表明，砂率和石粉含量均存在碾压混凝土抗裂能力最大的最优含量；掺入适量的氧化镁掺和料和合理增加水泥熟料中的C，S和C4AF两种矿物成分含量，对提高碾压混凝土的抗裂能力非常有利；骨料的弹性模量是影响混凝土弹性模量的重要因素，使用低弹性模量骨料可以大大降低混凝土的弹性模量，增大极限拉伸值，提高混凝土的抗裂能力。     

矩形垂直筛板的流体力学性能研究

在600mm的有机玻璃冷模塔中,用水-空气体系测定矩形垂直筛板的塔板压降、漏液和雾沫夹带等流体力学性能,确定了合理的塔板结构,使其具有较高的气液通量和较宽的操作范围,空塔动能因子最大可达3.0kg1/2(m1/2.s)-1,液流强度可达21.6m3/(m.h)。并对不同气液流量下塔板的流体力学实验数据进行关联和分析,得出了矩形垂直筛板的干板压降计算关联式以及漏液率随液流强度和空塔动能因子的变化关系,为矩形垂直筛板的设计提供了依据。与新垂直筛板相比,矩形垂直筛板具有更低的塔板压降。     

Measurement of the density and surface tension of Ni-based superalloys in the liquid and mushy states

The densities of three Ni-based superalloys have been measured in both liquid and mushy states by both a modified sessile drop method (MSDM) and a modified pycnometric method (MPM) for alloys CMSX-4 and CM186LC, and for CMSX-10 alloy by MSDM only. The surface tensions of liquid CMSX-4, CM186LC, and CMSX-10 superalloys were measured using the sessile drop method. All measurements were carried out in a highly purified argon atmosphere with the oxygen partial pressure of less than 10⁻¹⁹ MPa in the gas outlet. The densities of all superalloys in both liquid and mushy states were found to decrease with increasing temperature. The volume thermal expansion of each superalloy in the mushy state was found to be higher than that in the liquid state. The densities determined by different methods have been critically assessed and recommended values in both liquid and mushy states are given as a linear function of temperature for the three Ni-based superalloys. The surface tension of liquid CMSX-4 superalloy was found to decrease with increasing temperature, while that of liquid CMSX-10 superalloy increases with increasing temperature. The wetting behavior of liquid CM186LC on the alumina substrate was found (1) to differ significantly from that of CMSX-4 and CMSX-10 and (2) to vary with time. A HfO₂-rich layer was found in the contact area of CM186LC with the alumina substrate, which could lead to some uncertainty in the value obtained for the surface tension determined for CM186LC.     

修正热量法计算供热煤耗暨热电联产效益分析

介绍了热电联产成本的两种计算方法,指出了两种计算方法的局限性.对热电联产节能效果进行了量化分析,在按热量法对供热比计算的基础上,提出了修正热量法.此方法体现了热电联产的优越性,为发电企业增加了经济效益.     

60Si2Mn合金钢发蓝泛红的分析研究

本文探讨了60Si2Mn合金钢发蓝原理，针对其膜层泛红问题，分析了热处理、表面前处理、发蓝及浸油等过程对发蓝质量的影响，由此采取了相应的技术措施，生产实践证明发蓝质量稳定，生产效率明显提高。     

有机羧酸钠盐对PET结晶和熔融行为的影响

采用差示扫描量热仪研究了5种具有不同取代基的苯甲酸钠盐作为结晶成核剂对聚对苯二甲酸乙二醇酯（HET）结晶和熔融行为的影响，并同滑石粉进行了对比。结果表明，成核剂的加入能明显改变PET的结晶和熔融行为。苯甲酸钠、对苯二甲酸甲酯单羧酸钠和对羟基苯甲酸钠提高既汀的熔融结晶温度（Tc）分别达22．93、21．7和19．37℃，但使PET降解严重；对苯酚钠甲酸钠能够提高Tc达17．75℃且对PET相对分子质量影响很小；对苯二甲酸二钠成核作用最差。低于滑石粉。此外，成核剂的成核能力越强，PET双熔融峰中的低温峰顶温度就越高。     

Formation mechanism of 21R AlN-polytypoids in aluminothermic reduction and nitridation process

Synthesis of 21R AlN polytypoids was investigated using Al and ultrafine SiO₂ powder in a flowing nitrogen atmosphere by means of thermal gravity (TG), differential scanning calorimeter (DSC), X-ray diffractometer (XRD) and scanning electronic microscope (SEM) linked with energy dispersive spectrometer (EDS). The results showed that the formation mechanism of AlN polytypoids was different from that in reaction sintering process using Si₃N₄, AlN, Al₂O₃ and other sintering additive as raw materials. It was suggested that firstly Al reduce SiO₂ into Si and is also nitrided into AlN, then AlN, Al₂O₃ and SiO₂ dissolve into silicon liquid until the AlN polytypoids precipitate in saturated liquid in a flowing nitrogen atmosphere at lower than 1700 °C.     

世界钻井史上的第一支钻头——圜刃

在人类文明史上,中华民族文明是全球九个独立起源的文明之一(其余八个为古埃及文明、两河流域文明、古印度文明、爱琴-米诺斯文明、南俄文明、奥尔梅克文明、玛雅文明、查文文明)。在世界文化史上,中华民族文化是世界五大文化圈之一(其余四个是西方基督教文化圈、东方东正教文化圈、伊斯兰教文化圈和印度     

地球化学录井技术的发展和应用

简要介绍了国内地化录井技术的发展历程，分析了该技术的特点及在油气勘探开发应用中取得的成效。认为中国地化录井技术在引进、消化、吸收的基础上，扩展了该技术的应用领域和范围，目前该专业的整体技术水平处于国际领先地位。在以统计资料及应用实例报道该技术的应用成果及独特技术优势的同时，也分析了存在的问题，指出了解决问题的主要途径。