DCS分布式冷却系统在通信基站的应用研究

针对基站柜式空调耗电量大的问题,创造性地使用基站分布式冷却的方式,达到精确送风,节能高效的目的.在应用实践中检验了分布式冷却系统实际节能量和应用效果,总结出分布式冷却系统应用场景和范围,为更大范围推广应用DCS分布式冷却系统提供实践依据.     

THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

Rectangular Section Control Technology for Silicon Steel Rolling

Rectangular section control technology(RSCT)was introduced to achieve high-precision profile control during silicon steel rolling.The RSCT principle and method were designed,and the whole RSCT control strategy was developed.Specifically,RSCT included roll contour design,rolling technology optimization,and control strategy development,aiming at both hot strip mills(HSMs)and cold strip mills(CSMs).Firstly,through the high-performance variable crown(HVC)work roll optimization design in the upper-stream stands and the limited shifting technology for schedule-free rolling in the downstream stands of HSMs,a hot strip with a stable crown and limited wedge,local spot,and single wave was obtained,which was suitable for cold rolling.Secondly,an approximately rectangular section was obtained by edge varying contact(EVC)work roll contour design,edge-drop setting control,and closed loop control in the upper-stream stands of CSMs.Moreover,complex-mode flatness control was realized by coordinating multiple shape-control methods in the downstream stands of CSMs.In addition,the RSCT approach was applied in several silicon-steel production plants,where an outstanding performance and remarkable economic benefits were observed.     

仙游抽水蓄能电站尾水系统充排水试验

为检查工程质量,查找输水系统可能存在的问题并消除隐患,保障电站安全运行,福建仙游抽水蓄能电站在投产发电前,要对输水发电系统进行充水试验与放空排水试验,在试验过程中监测输水系统的应力、应变与渗漏水情况。本文以尾水系统为例,介绍了试验所应具备的工程条件、工作程序及技术要求、试验成果分析和存在问题处理等。试验表明,仙游抽水蓄能电站尾水系统设计合理,施工质量优良,结构可靠,可供同类工程参考与借鉴。     

双馈风机低电压穿越的改进技术

为提高电压跌落条件下双馈风电机组的运行稳定性,介绍了crowbar与chopper共同配合作用的低电压穿越技术,并从提高crowbar阻值整定上限这一角度通过理论分析与仿真验证说明了crowbar与chopper配合作用的优势。提出低电压穿越过程中机侧变流器的无扰切换控制方法,通过仿真验证了这种方法可以大大减少crowbar投切次数与低穿过渡时间,且控制简单可行。     

500 kV 开关弹簧机构支架螺栓断裂的原因分析及处理

HPL500B2型弹簧机构支架(BA)螺栓断裂可能导致开关分合闸失败,对其原因进行分析,发现BA螺栓由于预紧固力矩过大,接近其扭断力矩,使得作用在BA螺栓上的力偏高,BA螺栓安全系数仅为12%,安全系数较低。列出BA螺栓更换步骤及注意事项,并详细介绍分闸、合闸弹簧调整步骤,为类似事件的处理提供参考。     

不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

浅谈大型水电站继电保护信息管理系统设计及运用

某大型水电站继电保护信息管理系统结构与网络配置设计,成功解决了保护及安全自动装置与故障录波设施种类繁多、装置的通讯方式和通讯规约不尽相同、上送的数据量大等难题,不但可以将子站所有继电保护及安全自动装置、故障录波装置采集的信息上送主站,还可以通过Web服务在办公网络发布,并形成数据库和报表,实现数据统一管理,电厂信息化和智能化管理,非常适用于人员配置少、设备布置分散、自动化设备众多的大型水电站。     

脉冲电沉积镍-铜合金

采用脉冲电沉积技术在304不锈钢表面制备Ni-Cu合金镀层,镀液组成和工艺条件为:NiSO4ꞏ6H2O 200g/L,CuSO4ꞏ5H2O 10 g/L,十二烷基硫酸钠0.2 g/L,柠檬酸钠80 g/L,糖精0.2 g/L,pH 4.0,温度25°C,搅拌速率30 r/min,平均电流密度40~120 mA/cm2,脉冲频率0~100 Hz,占空比20%~90%,时间30 min。研究了平均电流密度、脉冲频率和占空比对Ni-Cu合金镀层的元素组成、表面形貌和显微硬度的影响,得到较优的工艺参数为:平均电流密度40 mA/cm2,脉冲频率50 Hz,占空比60%。该条件下所得Ni-Cu合金镀层由质量分数分别为56.53%和43.47%的Ni和Cu组成,呈“菜花”状形貌,结晶细致、均匀,显微硬度为614.4 HV。