Matrix morphology and fibre pull-out strength of T700/PPS and T700/PET thermoplastic composites

The main objective of this fundamental study was to investigate effects of processing conditions and resulting matrix morphology on interfacial bond strength of fibre reinforced thermoplastic composites. Using a hot stage microscope, single fibre pull-out samples were produced with T700S high strength carbon fibre and two semicrystalline thermoplastic matrices, polyphenylene sulphide (PPS) and polyethylene terephthalate (PET), respectively. Processing temperatures and cooling histories were the major variables in sample preparation. The T700S fibre had no clear effect on the surrounding PPS and PET matrix morphology, as long as direct cooling at constant rates was selected. A transcrystalline phase around the fibres could be induced in the T700S/PPS system, if isothermal crystallization was carried out at 227°C. Fibre pull-out tests were conducted at room temperature and two basic failure paths were observed, i.e. debonding at the fibre-matrix interface and cohesive failure of the matrix close to the fibre surface. The results indicate that slow cooling rate and a resulting coarse spherulitic morphology around the fibres correlate with high interfacial shear strength. In fact somewhat higher strength values were obtained for samples with transcrystalline layers around the fibres.     

Calendar maintenance of arbitrarily structured systems

A semi-Markov model is constructed that describes an arbitrarily structured multicomponent technological system and takes into account its calendar maintenance. Using an aggregation algorithm, approximate values of stationary reliability characteristics and an optimal term of maintenance work are determined for the system. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 2, pp. 69–86, March–April 2006.     

同心筒发射中旁泄流影响的数值研究

同心筒是一种先进的新型的舰载导弹垂直发射装置。文中采用动网格技术模拟了导弹在同心式发射筒内发射的瞬态过程。探讨了发射过程中旁泄流的产生与消失原因。通过设计内外筒的合理大小可以有效减弱旁泄流的影响。通过大量的数值实验,给出了避免外筒发生雍塞的代数关系式。     

隔壁精馏塔分离芳烃混合物的模拟研究

采用隔壁精馏塔分离苯-甲苯-对二甲苯物系,用Aspen Plus软件模拟了隔壁精馏塔内温度分布及液相组成分布,考察了汽相和液相分配比对产品纯度的影响。对隔壁精馏塔模拟得到的优化操作条件为:隔壁精馏塔的理论板数为30块,侧线采出在第14块理论板,进料段为15块理论板,在进料段的第7块理论板进料,进料组成n(苯)∶n(甲苯)∶n(对二甲苯)为1∶3∶1,回流比为8.8,液相分配比为2.96,汽相分配比为0.83。在此条件下,各组分的摩尔分数大于98.5%,与实验结果基本吻合。当进料组成n(苯)∶n(甲苯)∶n(对二甲苯)为1∶3∶1时,采用隔壁精馏塔可比常规两塔流程节能27.18%。     

Fluorescence Anisotropy of Cellular NADH as a Tool to Study Different Metabolic Properties of Human Melanocytes and Melanoma Cells

In this study, we wanted to see if fluorescence anisotropy could be used to detect changes in metabolism in cells with significant light scattering and absorption properties. Fluorescence anisotropy measurements of nicotinamide adenine dinucleotide (NADH) were performed with human melanocytes and melanoma cell lines. To demonstrate the feasibility of using fluorescence anisotropy for detecting metabolic changes, the electron transport chain was blocked using rotenone, inducing an accumulation of intracellular NADH. Total fluorescence increased in all cells as a result of rotenone treatment. Fluorescence anisotropy decreased in the rotenone-treated cells relative to the controls, suggesting an increased ratio of free to protein-bound NADH in the treated cells. In general, the fluorescence anisotropy of the melanocytes was significantly higher than that of the melanoma cell lines. Reflectance spectroscopy showed that the differences in fluorescence anisotropy between the cell types were not due to differences in scattering and absorption properties. Intrinsic cellular NADH fluorescence was experimentally extracted by ratioing polarized fluorescence to polarized reflectance. NADH binding, measured as the ratio of fluorescence intensity at 430 and 465 nm, showed more protein-bound NADH in the melanocytes than in the melanoma cells, consistent with the fluorescence anisotropy measurements.     

皂河闸小水电存在问题及改造探讨

针对皂河闸水电站因长期运行造成的机电设备老化、机组效率较低等问题,对3号机进行技术改造。经过调研分析,提出改造方案,并对改造前后的经济效益进行对比分析。表3个。     

Silicon power MOSFET at low temperatures: A two-dimensional computer simulation study

Understanding how the structure of the unit-cell affects the cryogenic performance of a Si power Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is an important step toward optimizing of the device for cryogenic operations. In this paper, numerical simulations of the Si power Double Diffused MOSFET’ (DMOS) are performed at room temperature and cryogenic temperatures. Physically based models for temperature dependent silicon properties are employed in the simulations. The performances of power DMOS’ with various unit-cell structures are compared at both room temperature and low temperatures. The effect of the cell structure on the on-resistance and breakdown voltage of the device are analyzed. The simulation results suggest that the device optimized for room temperature operation can be further optimized at cryogenic temperatures.     

Direct evaluation of singular integrals in elastoplastic analysis by the boundary element method

This paper presents a new method for the direct and accurate evaluation of strongly singular integrals in the sense of Cauchy principal values and weakly singular integrals over quadratic boundary elements in three-dimensional stress analysis and quadratic internal cells in two-dimensional elastoplastic analysis by the boundary element method. A quadratic triangle polar co-ordinate transformation technique is applied to reduce the order of singularity of the singular integrals. Next, a form of Stokes' theorem is introduced in order to remove the singularity in the Cauchy principal value integrals; therefore, the evaluation of these integrals can be carried out by standard Gaussian quadrature. Numerical examples of 2-D elastoplastic problems and a 3-D elastic problem show the effectiveness and efficiency of the method.     

β放射性气体浓度计的新分度方法

本文介绍β放射性气体浓度计的一种新的分度方法——泄漏元件排气法。其特点是一只元件可分度放射性气体浓度计的许多读出数(甚至是几个量程),操作方便。     

Improved coupled-mode theory of anisotropic optical waveguides

A coupled-mode equation for anisotropic waveguide systems of arbitrary cross section and general dielectric distribution is derived. Numerical results comparing the exact calculations to those of the method of Hardy et al. (Opt. Lett., vol.11, 742-4, 1986) show that the same accuracy can be obtained not only for TE, but also for TM mode coupling in the case of anisotropic waveguides, and the improved coupled-mode theory is applicable to the situation when moderately strong coupling occurs under the condition where the edge-to-edge separation of two coupled guides D₂ is about 0.1 μm