锂-二氧化碳电池阴极催化剂的研究进展

锂-二氧化碳电池通过捕获、转化二氧化碳为储能物质，既可以减少二氧化碳排放量又可以作为创新的储能装置，引起了研究者们的广泛关注。本文简单介绍了锂-二氧化碳电池的工作机理、发展历程和目前研究存在的难题，通过对研究工作的总结、电池性能的对比，将不同类型的催化剂进行了系统的分类和简单的概括，综述了催化剂的设计理念和研究现状，提出了催化剂目前存在的难题与挑战，并展望了催化剂未来的发展方向。本文主要针对锂-二氧化碳电池阴极催化剂的最新研究进展进行了详细的阐述，指出高效的阴极催化剂是促进锂-二氧化碳电池电化学反应动力学、降低充电平台和过电势的关键所在。     

综放面本煤层预抽瓦斯的治理技术

为了极大限度地提高本煤层预抽效果，以马兰煤矿为研究对象，针对目前马兰煤矿的瓦斯赋存情况和现阶段所采取的抽放措施，从抽放钻孔的孔径、孔深、布置方式、封孔质量和增加煤层透气性等方面进行探索。实践表明，以上方法的运用，能够有效地提高本煤层预抽抽放效果，保证工作面安全生产。     

Valorisation of potato wastes

Potato processing industry has a high degree of discarding, which currently has low added value being used primarily for animal feed. However, potato wastes offer a broad range of interesting components such as antioxidants, starch, protein or fibre with potential applications in the food and non-food industries. The recovery of these high valuable fractions using efficient multistage and multiproduct processes could be of great interest. This short review provides a general overview on the integral valorisation of potato wastes, offering an updated vision of the main residual parts generated during potato harvesting and processing, the high valuable obtained components focusing on the bioactive ones and the potential of the emerging extraction techniques over conventional ones. In addition, innovative applications are discussed to highlight the scientific and applied interest of these underutilised and undervalued fractions and to emphasise the integral valorisation of raw materials.     

Aluminum based reflective nanolens arrays to improve the effectiveness of ultraviolet inactivation of Escherichia coli O157:H7 and Listeria monocytogenes in water and a sucrose solution

Food Science and Biotechnology - Aluminum based reflective nanolens arrays were developed via a series of aluminum electropolishing and anodization steps with subsequent selective dissolution of...     

Ternary Blends of Renewable Fast Pyrolysis Bio-Oil,Advanced Bioethanol,and Marine Gasoil as Potential Marine Biofuel

An alternative for reducing emissions from marine fuel is to blend bio-oil from lignocellulose non-edible feedstocks to diesel fossil fuels. Phase diagrams of the ternary systems were built to represent the transition from heterogeneous regions to homogeneous regions. Four homogeneous blends of bio-oil of eucalyptus-bioethanol-marine gasoil were experimentally characterized with respect to the most important fuel parameters for marine engines: water content, flash point, low heating value, viscosity, and acidity. Blends with closer properties to marine gasoil replacement, lower costs, and environmental impacts should be tested for large engines.     

床温及SNCR脱硝对CFB锅炉NOx和N2O排放影响的试验研究

为了研究循环流化床（CFB）锅炉燃用无烟煤时床温及选择性非催化还原（SNCR）脱硝对于NO和N2O排放的影响，在1 MW CFB试验装置上开展了试验研究。结果表明:床温由880 ℃提高到970 ℃，NO排放质量浓度由119.5 mg/m3上升到226.0 mg/m3，N2O排放质量浓度由216.0 mg/m3降低到102.2 mg/m3；在氨氮摩尔比（NSR）为0~3.7之间，随着NSR的提高，脱硝效率从0上升到50.72%；进一步提高NSR到5.2，脱硝效率升至53.61%，增加较为缓慢；随着NSR从0提高到1.7，N2O排放质量浓度由84.3 mg/m3上升至118.3 mg/m3，增长较为缓慢；进一步提高NSR至2.0，N2O排放质量浓度上升至187.7 mg/m3，增长速度提高；继续提高NSR至5.2，N2O排放质量浓度上升至381.4 mg/m3；CFB锅炉采用以尿素为还原剂的SNCR脱硝工艺时，单纯通过加大NSR来提高脱硝效率不仅效果有限，过量喷入的还原剂会造成N2O排放量的显著提高。     

膜级钛系聚酯与锑系聚酯的成膜性能比较

利用流延膜挤出机、拉膜机分别对锑(Sb)系聚酯和钛(Ti)系聚酯进行挤出、拉伸成膜,考察了两种聚酯的成膜性能,对两种聚酯在加工过程中的热稳定性以及薄膜的热性能、力学性能、光学性能、取向结构进行了表征。结果表明:在挤出、拉伸过程中,Ti系聚酯的黏度降高于Sb系聚酯,Ti系聚酯切片的结晶度明显小于Sb系聚酯,但Ti系聚酯薄膜的结晶度与Sb系聚酯薄膜相当;在相同的成膜工艺下,Ti系聚酯薄膜的弹性模量、光学性能与Sb系聚酯薄膜相当,拉伸强度高于Sb系聚酯薄膜,断裂伸长率低于Sb系聚酯薄膜,双折射率大于Sb系聚酯薄膜。     

应用独立分量分析的激光测风雷达湍流频谱分解

针对大型风力发电机机组中常见的脉动湍流、风机尾流与涡流等湍流信号,研究了利用自然梯度下降的独立分量分析方法的湍流频谱分离效果,以区分中心风速与湍流信号,提高风机机组的综合工作效率。首先分析了风机组中常见湍流信号的后向散射与频谱分布特点,然后依据这些特点设计了对应的独立分量分析模型。在仿真结果符合要求的基础上,进行了双目激光雷达天线的风速采集与实际分离效果检测。实验结果表明,在大气折射率结构常数C2n≤10-14同时广义大气常数α≥4的通常情况下,利用双目信号能够分离出一个湍流中心和一个中心风速。对1 s内两个谱峰的波动范围进行统计,获得(2.59±0.05)MHz的中心风速以及(1.22±0.19)MHz的湍流中心估计,且二者的平均信噪比分别为25.93 dB和31.01 dB,能够在获得稳定的中心风速估计的同时得到一个较为稳定的湍流中心估计。