自然循环工况下离心泵阻力特性的实验研究与数值模拟

停转后泵的阻力特性对自然循环流量影响明显。为研究低流量自然循环工况下离心泵的阻力特性，设计了实验台架，对离心泵的正向压降、反向压降和损失系数进行了测量，实验雷诺数为2.0×10⁴～1.5×10⁵。实验表明：相同雷诺数下，反向压降明显高于正向压降；雷诺数大于8×10⁴时，损失系数基本保持不变，而低雷诺数下损失系数随雷诺数的降低有增大的趋势；基于实验得到了损失系数的经验关系式。采用CFD方法对离心泵的内部流场进行了模拟，计算表明：CFD方法能较好地预测损失系数，RNG k-ε模型与实验值的相对误差不超过10%；离心泵的压力损失主要集中在叶轮、导叶等结构的交界区域；正向与反向流动的流场分布存在显著区别；低雷诺数下局部流动更加不稳定。     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.     

Distortion visualization techniques for 3D coherent sets: A case study of 3D building property units

In the fields of 3D cadastre and 3D property management system, numerous building property objects are adjacent as primary property units assemble into a 3D coherent set. During visualization process of the coherent set, occlusion, obscure, mazy spatial relationships and relative location relationships among the units of the coherent set cause difficulty in observing and understanding the set and its units. Common 3D objects viewing method, such as rotation and navigation obtaining desired visualization effects through adjusting the view angle and position of the camera's field of view, provides weak interactive experience and orientation control for the coherent set because of the neighbour relationships of the 3D objects inside the set. In this paper, a novel method is proposed to solve the prior problems with two basic distortion methods based on “focus + context” theory. The coherent set is first discretized into individual objects and changed them locations according to linear or orthogonal function, while keeping their relative location and dual topological relationships. To maintain both global context awareness (topology and locations) of 3D coherent set and highlight effect of the focus 3D building property object, three evaluation indexes are adopted to assess the corresponding distortion results. A case study based on the real clustered 3D property in Shenzhen was conducted to evaluate the performance of distortion functions, the result shows that the method proposed in this article can not only expand the visual area of focused object and create a clear line of sight (LOS) to the focal object previously obscured, but also maintain verticality and proximity in some degree to facilitate understand the spatial occupation and distribution of whole coherent objects.     

Fabrication and properties of Si3N4 based ceramics using combustion synthesized powders

Silicon nitride (Si₃N₄) based ceramics were fabricated with β-SiAlON and Si₃N₄ powders synthesized by combustion synthesis method via power injection molding (PIM). In the PIM process, the solids loading for each material was first determined from the results of the torque rheometer experiment. The mixing process was repeated to produce the homogeneous feedstock, and homogeneity of feedstocks was evaluated by observing the shear viscosity with time at a constant shear rate. The rheological behavior of feedstocks was investigated using capillary rheometer. It found that both feedstocks have no problem in injection molding. The binder decomposition behavior was also investigated, and a wax-polymer binder system was nearly removed by the optimized solvent and thermal debinding processes. Thereafter, the debound samples were sintered at 1750 and 1800 °C for 4 h in nitrogen atmosphere. Regardless of sintering temperature, the relative density of higher than about 96% was achieved. When comparing mechanical properties including bending strength, Vickers hardness and fracture toughness, Si₃N₄ with 2 wt% Y₂O₃ and 5 wt% Al₂O₃ (Si₃N₄+2Y5A) had higher values than β-SiAlON with 4 wt% Y₂O₃ (β-SiAlON+4Y) regardless of sintering temperature. It was supported by observing the microstructures of the plasma-etched samples.     

基于三相感应电机的小型化超低频发射天线研究

针对低频电磁传输中天线尺寸过大的问题，设计了一种基于三相感应电机的小型化超低频发射天线.电机工作时产生了时变低频电磁场，可作为超低频发射天线.为有效分析其电磁场分布，文章建立旋转磁偶极子数学模型以等效电机内部旋转时产生的磁场.首先，对电机内部磁场和旋转磁偶极子的关系进行阐述，利用麦克斯韦方程组，得到旋转磁偶极子的电磁场分布.其次，通过电磁仿真软件验证旋转磁偶极子的近场分布特性和远场辐射特性.最后，通过实验对电机近场的磁场分布进行验证.仿真和实测结果表明，三相感应电机具有超低频天线的辐射特性.     

Two-level intelligent modeling method for the rate of penetration in complex geological drilling process

The rate of penetration (ROP) model is of great importance in achieving a high efficiency in the complex geological drilling process. In this paper, a novel two-level intelligent modeling method is proposed for the ROP considering the drilling characteristics of data incompleteness, couplings, and strong nonlinearities. Firstly, a piecewise cubic Hermite interpolation method is introduced to complete the lost drilling data. Then, a formation drillability (FD) fusion submodel is established by using Nadaboost extreme learning machine (Nadaboost-ELM) algorithm, and the mutual information method is used to obtain the parameters, strongly correlated with the ROP. Finally, a ROP submodel is established by a neural network with radial basis function optimized by the improved particle swarm optimization (RBFNN-IPSO). This two-level ROP model is applied to a real drilling process and the proposed method shows the best performance in ROP prediction as compared with conventional methods. The proposed ROP model provides the basis for intelligent optimization and control in the complex geological drilling process.     

Traffic identification method based on multiple probabilistic neural network model

Neural Computing and Applications - Traffic identification is currently an important challenge for network management and security. In this paper, we propose a novel application identification...     

Torsional statics of two-dimensionally functionally graded microtubes

A size-dependent governing equation is derived to investigate the torsional static behaviors of two-dimensionally functionally graded microtubes based on the modified couple stress theory. The shear modulus is assumed to vary along the tube’s length direction according to an exponential distribute function, and varies along the tube’s radius direction according to a power-law function. A generalized differential quadrature method is developed to determine the rotational angle and shear stresses. Some illustrative examples are given to investigate the effects of applied torques, the length scale parameter and various material compositions on the torsional angle and shear stresses.     

Fabrication of BSCF-based mixed ionic-electronic conducting membrane by electrophoretic deposition for oxygen separation application

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF), which exhibits a high mixed oxide ionic-electronic conduction, was used for the fabrication of an oxygen separation membrane. An asymmetric structure, which was a thin and dense BSCF membrane layer supported on a porous BSCF substrate, was fabricated by the electrophoretic deposition method (EPD). Porous BSCF supports were prepared by the uniaxial pressing method using a powder mixture with BSCF and starch as the pore-forming agent (0–50 wt.%). The sintering behaviors of the porous support and the thin layer were separately characterized by dilatometry to determine the co-fired temperature at which cracking did not occur. A crack-free and thin dense membrane layer, which had about a 15 μm thickness and >95% relative density, was obtained after optimizing the processes of EPD and sintering. The dense/porous interface was well-bonded and the oxygen permeation flux was 2.5 ml (STP) min⁻¹ cm^-2 at 850 °C.     

高碘酸盐的活化及降解水体有机污染物研究进展

根据高碘酸盐活化方式、活化机理和相关自由基种类等方面,叙述了国内外高碘酸盐高级氧化体系降解水体有机污染物方面的工作。基于氧化剂为高碘酸盐的高级氧化技术氧化能力强,能在较宽的pH范围内高效降解包括抗氧化能力极强的全氟辛酸(PFOA)在内的多种有机污染物,在水处理领域具有较好的应用潜力。依据目前的研究现状,结合实际需求,认为进行废水处理的小试或者中试、优化活化理论研究,以及明确各活性物质对有机物选择性降解的机理,是将来需要关注的问题以及研究方向。